More pictures! More story!
I take 9.3x66 case and run it thru my homemade belting dies and..........I end up with a 405 belted case that can be loaded with 405 dies
I also rebate the rim to .473".
Waiting on a Shilen Barrel.......and I also need to grind a reamer.
The case holds 78 grains of water.
I like the cut off 260 grain X bullet, but with deeper free bore I can load the 300 to a length of 2.530"
The ole Axis test gun is getting a work out!
Also working on a 444 Belted using a 9.3x62 case.
Last edited by Underhammer; 07-14-2019 at 10:30 PM. Reason: more info
More pictures! More story!
The Dunning-Kruger effect is alive and well.
The 405B mag is long enough to let me seat a 300 X out another band, making plenty of room for powder.
I just need to throat the bore deeper. Not sure about that, yet.
Shown with a 268X.
And,
The Shilen .411 barrel is being shipped, now I have to make the reamer.
The finish and die reamers are ground round. Just need to relieve the cutting flutes.
And either buy or make the pilot bushing. .252 pilot.
I did not make the belt step, I will cut that separate.
8 degree taper, .100 freebore ].313] and 1.1/2 degree throat. It is like having .200 freebore.
While I had the taper set, I decided to cut the die reamer also.
And the best part is, you can also shoot belted 06 brass.
This is so very cool! You are a DIY’er to look up to my friend!
More please!
[ UPDATE ]
Just ran a starting load thru the new chamber. Hodgdon calls for 55.0 of Varget at 2079 fps. with a 24" barrel. [starting load ]
I made a 23" barrel and got 2039 fps for my first test shot. [ Hornady 300 FP ]
So I am right on par with 405 Winchester load data.
Plastic stock and steel one pc. base weigh in at an even 7#s.
So what do belting dies look like.
I have wanted something like the .450 Marlin but fitting a std bolt face. Looks like these are close enough.
Just shot a case full of Benchmark and a 270 Barnes TSX..............2569 fps.........just shy of 4000 ft #s of energy!
The factory plastic stock is still doing fine, but keeping an eye on it.
Now to mount a scope and do some group testing.
Should have the brake installed next week.
They are just tapered dies that reduce diameter .010 each [.007-.008]. Takes 2 dies, then the third one has a sharp edge to help seat in the belt.
Third die is used in an arbor press.
Then I finish them in a lathe.
All home made stuff.
CH4D use to make these, might contact them.
targets?
The Dunning-Kruger effect is alive and well.
https://photos.app.goo.gl/iZHNXHW7aJ8NmHVr5
2570fps.
Can't get the photo to load, hope the link works.
https://photos.app.goo.gl/oQmH3wnQtAFHZWbB7
The lower shot was a scope adjustment, then fired the next three. 2545 FPS....300 TSX.
Both the 210 TSX and turned down Monoflex 208gr, will hit 3000 FPS!
That is a point blank range of 300 yds.
link to chart:
https://photos.app.goo.gl/kp4LSPyvJ12PqCcE9
I have a high scope at 2".
Picture of the rifle. Factory stock is doing OK.
https://photos.app.goo.gl/qrpTqBMBMbmDjgqf8
Bookmarks