.308Win. Starter reloading kits.

[LoneWolf]

Would like to know what reloading starter kits are good to start with for reloading 308Win.

Was looking at some of the kits on amazon, I'm not even sure which ones have everything that's required.

Would like some input from the experienced reloaded on what they started with.

Thanks in advance gentlemen.

Sent from my HTCEVOV4G using Tapatalk 2

[stangfish]

What is your price range? Some kits have good stuff in them some are pretty cheap after the press. If you have a number in mind you can forgo a kit and get what you need, possibly even used or sans all the throw away stuff.

The Items you will need for certain(Not to mention powder, primers and boolits):

Press
Dies
Scale
Powder scoops/spoons
Powder Funnel
Powder Trickler
Reloading Tray
Priming Tool(hand press)
Reloading Manual


At some point in the near future:
Dial Calipers
Case Trimmer
Powder Throw
ID/OD Chamfer Tooling
Primer Pocket Uniformer
Flash Hole Debur Tool
Headspace Gauge
Stoney point or Ogive Dimension Inspection Tool

[fgw_in_fla]

I started with one of these back when they only cost $79. Over the years I've added better scales, another press (Lee Turret), all kinds of goodies.
Welcome to your next addiction. After you own at least 3 Savage rifles & reload you'll be what's known as Savage Addict / Reloading OCD. Meetings are held every Thusday. Stang usually moderates since he has a degree in addiction treatment.
http://www.natchezss.com/product.cfm?contentID=productDetail&brand=LE&prodID=LEE90030&prodTitle=Lee Breech Lock Challenger Press Kit

[fgw_in_fla]

Oh, and a word on calipers. Digital is nice but analog will never run out of batteries....

[LoneWolf]

The Lee kit was one I was viewing. I don't like to be real cheap, but a good starter kit to get the hang of things and figure out how far I want to go down this rabbit hole. I'll most likely get sucked right down it though lol.

Sent from my HTCEVOV4G using Tapatalk 2

[stangfish]

You never said your budget.

As far as Lee goes, the classic cast is good to go.As good as anyone elses or close to it. Some of the other component are ify. Bottom line is that if you go the dirt cheap lee kit there is the possibility you will replace everything within a year.

[big honkin jeep]

The Lee anniversary kit has about everything you'll need except caliber specific items like dies and a case length gauge. Their equipment though less expensive than most is quite good and loads some really good ammo.
I would also recommend Modern reloading by Richard Lee as a very good manual to start with. If you read it all from the beginning up to the load data you will have a pretty good grasp of the fundamentals and should be ready to start reloading. I would also recommend their deluxe die set. It comes with a neck sizing die that sure makes things easy as case lube is not required when using it.

[missed]

I bought one of the lee breech lock kits. I really like the breech lock feature. There powder dispenser for it being kinda cheap works pretty well.

The scale sucks. I do have a old ohaus 10 10 and my ohaus digital.

Good calipers make it nice. I have mitutoyo analog and a digital. And I use comparators that I made.

I am using lee dies, with no complaints

I use the lee zip trim that goes into the press and it works great.

[LoneWolf]

Sounds good for the Lee kit, now if I jump into the higher price category of some like the RCBS rock chucker supreme master reloading kit. Is it going to be that much of a higher quality and how does the higher quality ease the process?

Sent from my HTCEVOV4G using Tapatalk 2

[MacDR]

Lee kit is an inexpensive start and you will keep most of it. Deluxe dies and case length gauge and cutter and you are good to go as mentioned above. Calpers, digital or manual are needed. The Lee book is a good read and will steer you in a safe direction. Lyman and Hornady also publish good manuals. I am not familar with others so can't comment on them.

[masterblaster]

I' ve used Lee for almost 30 years now and am just starting to get fancy (lazy), I got the WFT trimmer, RCBS Chargemaster and the lock n load bushing set from Hornady as it fits in my old lee classic single stage press. Read the loading manuals, use youtube and the forum when you have a question.

[big honkin jeep]

Sounds good for the Lee kit, now if I jump into the higher price category of some like the RCBS rock chucker supreme master reloading kit. Is it going to be that much of a higher quality and how does the higher quality ease the process?

Sent from my HTCEVOV4G using Tapatalk 2

In my opinion... It wont.
Nothing against RCBS or any of the others but just not enough difference in performance to justify the added expense for a starter or hobbyist reloader..

[thermaler]

I just started hand-loading just over a year ago, and the Lee kit is a good starter one--especially since when starting out I didn't have a clue what all the stuff was needed. You can always use other folk's higher quality dies and then get a better press. The main thing about the Lee is that it's rather slow--but it does get the job done. 308 is the perfect caliber to start with too IMO.

[LoneWolf]

That's why I chambered for a round with decades of data! Looks like I'll be investing in the Lee kit in a little while. Love the honest insight from this forum.

Sent from my HTCEVOV4G using Tapatalk 2

[stangfish]

Is it going to be that much of a higher quality and how does the higher quality ease the process?


Knowledge and tools ease the process of accuracy. To go from factory ammo to reloading opens your eyes. It becomes one or the other of necessary evil or constant quest for perfection.

[bootsmcguire]

The Lee anniversary kit has about everything you'll need except caliber specific items like dies and a case length gauge. Their equipment though less expensive than most is quite good and loads some really good ammo.
I would also recommend Modern reloading by Richard Lee as a very good manual to start with. If you read it all from the beginning up to the load data you will have a pretty good grasp of the fundamentals and should be ready to start reloading. I would also recommend their deluxe die set. It comes with a neck sizing die that sure makes things easy as case lube is not required when using it.

+1 with all of that. To add to what big honkin jeep said, using the Neck sizing die (called the Lee Collet Die) will also help extend your brass life and adds accuracy in my experience over Full Length sizing each loading.

Something you may want to consider is going with one of the Lee kits that includes a Turret Press rather than a single stage press. I started with a Lee single stage kit and later on upgraded to a Lee turret press. You can run the press as a single stage or progressively if you wish, and as you add calibers to your reloading inventory you can use the interchangeable turret heads to ease your switch from one caliber to another.

I started with Lee and have had no regrets with the brand choice. I only wish I would have started with the turret press. It would have saved me money having to upgrade later, and that's money I could have used to buy more boolits, powder, and primers.

[Sitting Duck]

Don't be afraid to pursue a used setup. All of the big names work well, it seams. It doesn't get simpler than a single stage press, beam scales, and almost anybodies dies. Most of this equipment, even used, will outlast you. Leaves money for powder, bullets, primers, and fancy cartridge headspace guages, etc.

[LoneWolf]

I'm not afraid to buy used I just don't want to try and piece together a kit from random used gear. I kind of have to jump into things from the get go.

I learned that lesson a long time ago when I wanted to play guitar and my mom said I had to learn piano first. Piano wasn't interesting enough and I got bored quit and never learned how to play guitar.

With most of these types of things it's best to start off with all the right tools (even if they aren't the best) to avoid the frustration of missing something required to get the job done properly.

Sent from my HTCEVOV4G using Tapatalk 2

[LHitchcox]

The Lee kit works really well. I will say that the powder measure is great with stick powder, but binds with ball powder (at least mine does). The scale is a bit odd compared to most, but it works well. As said above a dial or digital caliper is a necessary add on. Lots of folks seem to overlook case trimming. The Lee system when chucked into a cordless drill works really well. Buy the pilot and shell holder combo and you are good to go.

[thermaler]

The best part is--you no longer have to go to the store and say "****it, no more ammo available!" (instead, you get to say "****it, no powder/bullets/cases available!"). Your worst enemy when stalking supplies is other reloaders. : )