you can rework it yourself.
Ive used my RCBS brass reamer/chamfer to clean up a 22 crown, ive also used wooden cone shaped blocks and sand paper on muzzle loader crowns.
Just be careful and go slow.
Good luck
Is there an easy way to dress a barrel crown?
My son's .270 has accuracy issues. The end of the barrel has a few bad dings in it & I'm quite sure it has to affect accuracy. He has no idea how it got damaged . (I swear the kid takes after his mother, rest her soul). I was thinking I might use a spherical shaped very fine grinding stone. the kind one would use on a Dremel and such. I have them in different diameters. Can I take one that matches the crown radius / curvature & hand dress it or do I need to take out a mortgage, send it out & have it reworked?
Any input is most appreciated.
'Scuse me while I whip this out...!
you can rework it yourself.
Ive used my RCBS brass reamer/chamfer to clean up a 22 crown, ive also used wooden cone shaped blocks and sand paper on muzzle loader crowns.
Just be careful and go slow.
Good luck
The purpose of the crown is so that when the bullet leaves the barrel, the entire base of the bullet exits the muzzle at the same time so there is no gas blowing on one side of the bullet while the other side is still in contact with the barrel.
In order to do this, you would need a tool that has a spud to keep the tool in proper alignment with the bore. Otherwise you will simply be compounding the problem.
I have the tools and do my own recrowning. You might first start by asking around your shooting friends or at your range and see if someone will help you. Gunsmiths typically do not charge much for crowning unless they have to chuck it up on a lathe.
I'm headed to the range right now, before the wind picks up & the rain (if applicable) starts. I know a few 600 yard guys that shoot there pretty regular. Past discussions I've heard them say they do most of their own work. I wonder if any of them need any electrical work to trade for a barrel crown dressing?
Most appreciate the input.
Thanx, again.
'Scuse me while I whip this out...!
I do it for free for my friends. Or I let them do it while I supervise, in case they dont like what they get.
I had my 30 year old 30-06 re-crowned a few years ago and I think it cost me $50 if that.
I strongly suggest having it professionaly done. Well worth the small expense. Also check that the barrel and tang are free floated, the action screws are tight (35-45 in lbs) and accuracy may improve. If this rifle has been shot quite a bit check to see if the barrel needs to be de-coppered. Adding pillars for the mounting screws may help. There are many reasons why accuracy falls off but those I mentioned are ones you can do yourelf except for the barrel crown. Savager barrels shoot better dirty except for excess copper which can happen in new Savage barrels until they smooth out. Good luck.
El Lobo
Hey I love that! I wonder why other barrels dont shoot good dirty? Is it just Savage?Originally Posted by ellobo
HotBrass, it has something to do with the button broached rifling which most makers are using on thier facotry installed barrels. In days gone by barrels were cut broached which was much smoother. I imagine it does it to other makes as well. I only have a Mauser commercial actioned rifle, a Winchester model 88 that is 60+ yrs old to go along with my Savages so cant answer to other makers barrels. The Mauser has a cut rifled barrel and is silky smooth and sub MOA. The gold and silver inlays dont hurt either :). The model 88 is Minute of Deer accurate.
El Lobo.
Do a search for "brass screw" "lapping compound" crown, came up with the following.
Originally Posted by shelbyfan
Whenever the legislators endeavor to take away and destroy the property of the people, or to reduce them to slavery under arbitrary power, they put themselves into a state of war with the people, who are thereupon absolved from any further obedience
Insane. Not on my guns!Originally Posted by sha-ul
Done this many times. But only to barrels that needed a crown job. If it dosn't work I take it to a smith for a professional job. Most times "it works"Originally Posted by hotbrass
I guess he doesn't realize that the Savage repair shop uses this technique too.Originally Posted by Ray Gunter
Whenever the legislators endeavor to take away and destroy the property of the people, or to reduce them to slavery under arbitrary power, they put themselves into a state of war with the people, who are thereupon absolved from any further obedience
Here ya go.......
http://www.youtube.com/user/MidwayUS.../1/x3ELBpqYCQc
you can use brass screws as well (watch the video...you will understand).
Be careful of what you wish for, and always be mindful of what others are trying to accomplish
A brass screw for a crown job? I like to hear that from Savage.Originally Posted by sha-ul
I dont think brass is gonna hurt it regardless. You stick brass in the other end.lol
Not thinking about brass hurting it. My concern is how are you going to polish off a high spot freehand
without also polishing off the low parts of the crown. That is why you need a spud or bore guide to keep the polishing at the correct angle in line with the bore.
if you use a round brass button no matter how you hold it its gonna polish at the same angle
Yes, and it will polish the low side as well as the high side, so what have you accomplished?
The high bit will polish down faster than the surrounding areas, as they will have less pressure on them, until the surface is uniform all around. just like lapping in a valve.Originally Posted by hotbrass
Whenever the legislators endeavor to take away and destroy the property of the people, or to reduce them to slavery under arbitrary power, they put themselves into a state of war with the people, who are thereupon absolved from any further obedience
the ball will ride on the high points until it creates the perfect cradle to ride in. Once the hole is round, then it will be even pressure on the edges of the entire circle
+1 - here is Brownell's version for the pros - http://www.brownells.com/.aspx/pid=8...E-CROWNING-LAPOriginally Posted by sha-ul
I have used both the Brownells product and a nice round head brass screw - both work fine but if you are nervous about it a smith should only charge about $40-60 to crown a barrel for you (be advised he will probably be using some version of the brass lap to finish things up!).
Uh, not really but it you think you can control it that well. Have at it.Originally Posted by keeki
Yes looks just like mine. But it is used after you cut the crown. If you just go after a bad crown with it , you will end up with another bad crown, but it will be nice and polished.Originally Posted by Eric in NC
Thanks to all for all of the really cool ideas. I ended up doing it the el cheapo way. I have a bunch of polishing stones in every size / shape imaginable. Many of them are very fine stones so, I used a 5/8 inch diameter sphere & hand polished the crown. Worked like a charm. The range test revealed that was the problem. It started to shoot to the high left and very scattered. This was using ammo that was typically on the money accurate. When I got it, the crown was clearly chipped / gouged with no explanation from my son on how it happened. It almost looked like somebody had used a nail or something and was picking at the muzzle / crown. Maybe I'll beat it out of him....
Anyway, the stone sphere I used was very fine & left a nice shine to it. Now, all I need to worry about is rusting.
Thanks again to all for your input.
'Scuse me while I whip this out...!
Bookmarks