pipe wrenches, but they leave marks
what part of the country are you in, maybe some one near that can help.
I don't really have the money to get a proper tool right now, and I really don't want to pay a smith to put my new barrel on. Is there any other tools that I may have laying around the house or I can pick up at Lowes to do the job of loosening and tightening the barrel nut?
Tank
pipe wrenches, but they leave marks
what part of the country are you in, maybe some one near that can help.
.223 Rem AI, .22-250 AI, .220 Swift AI .243 Win AI, .6mm Rem AI, .257 Rob AI, .25-06 AI, 6.5x300wsm .30-06 AI, .270 STW, 7mm STW, 28 nosler, .416 Taylor
Live in central PA. I have access to a couple of different gunsmiths, but really didn't want to have to a pay a smith either.
Tank
Sharp Shooters Supply sells a very good barrel nut wrench for about $40 and Midway has an adequate one for $30. You can improvise a barrel vise with a bench vise and some inletted hardwood blocks.
A gunsmith will probably charge that or more than the proper wrench. I suppose a pipe wrench will do the job but you won't like the way the rifle looks after you are through. Do it with the correct tool.
there are quite a few members in Pa, you might post a town nearby& see if anyone else is nearOriginally Posted by liltank
Whenever the legislators endeavor to take away and destroy the property of the people, or to reduce them to slavery under arbitrary power, they put themselves into a state of war with the people, who are thereupon absolved from any further obedience
I've used this method on other things that I didn't want scratched, marred or damaged.. Use something soft between the barrel nut and pipe wrench. Good cheap item is a copper tubing fitting that you sweat onto the pipe. Get a coupling close to the diameter of the barrel nut. Cut with a hacksaw to cover the barrel nut then cut a slit in it allowing it to expand or contract depending on original size. I would make sure to use Kroil penatrating fluid on the threads before attempting anything.. My experience is most nuts are not overly tight but my first one was one from hell. You could do the same with the action and another copper coupling clamping it in a vise with 1/4-28 bolt in the front action hole preventing it from turning in the vise. If you proceed slowly and watch what your doing I believe you could successfully loosen the barrel nut.
Installing a new barrel isn't where you really need the tool, getting a factory nut loose is a different story. Don't mean to sound negative but if you can afford the barrel, headspace gage, and to shoot the new barrel in what is a $40 tool?
Well I kinda blew my budget on the barrel and a few other things. I will more than likely just take it to the one smith. He said it would be $50 or $60 to set the head spacing and put the new barrel on. I wanted to see if I could get away with a generic way of doing so. Guess I will have to bight the bullet for now. I plan on getting the proper tools eventually so that I can switch calibers.Originally Posted by leather5to1
Tank
P.S. Don't own the head spacing gauges either. Would have to purchase those as well. Was going to set off a sized piece of brass.
All it takes is and 1 1/4 box end wrench and some drill bits, put the wrench on and fit 4 bits into the slots on the nut till it's tight enough to lock on the nut and turn it. Worked very well till I got the right tool!! Might have been a 1 1/8th after thinking about it. ::)
no comment!!.....jesus
http://www.midwayusa.com/viewProduct...tnumber=288765
where in central PA and what caliber?
All it takes is and 1 1/4 box end wrench and some drill bits Never thought of that, now that is ingenuity :D
Another short cut is to use the pipe wrench to get the old nut off and then replace the nut with a new or used one. Lots of guys did that with the smooth nut that had the hole for the pin spanner.
Originally Posted by liltank
The wrench Jim has at NSS is $25, nice well made wrench too.
If your a tool guy you must have a STRAP WRENCH laying around, use the pipe wrench to take off the nut (unless you don,t have another nut) then use the box wrench and then use the strap wrench to put the nut on
Sorry to high-jack the thread :) I've got plenty of the tools, just don't have the funds for the barrel's :'(
It was shameless idea steeling, works great without damaging the nut like a pipe wrench and I have extra long wrenches so I don't have to beat on things, the harder you pull the tighter the drill bits cam, found it to be stronger than the Wheeler wrench, now use the SSS wrench for the most part but if I hit a had one I use the wrench and drill bits, haven't ruined a nut yet, knock on wood! Haven't ran up against the new nut yet ???Originally Posted by possum1
What size drill bits? I like the concept.
uj
Thanks for the help guys. A couple guys stepped up and giving me proper wrench opportunities.
Thanks,
Tank
Bookmarks