A proper crowning tool is not that expensive and saves a lot of time
On Friday, I cut a Savage factory 22" barrel down to 20" for the third time. Two of those were .308 barrels and this one was a 6.5 CM - all sporter profiles.
I am cutting and crowning these barrels with common hand tools. Hacksaw - Dremel rotary stone - File - Sandpaper - Large brass screw chucked in hand drill - Birchwood Casey cold blue pen.
In all three cases, the "garage" crown job produced better groups than the factory crown.
Has anyone else had this experience?
A proper crowning tool is not that expensive and saves a lot of time
I have cut several barrels down and crowned with a shell deburring tool. They all shoot 1/2 moa. I read an article once where they tried to mangle a crown and could not get the groups to open up. A couple of shots smoothed out any damage they did.
It’s probably a shorter stiffer barrel resulting in better accuracy. Not likely the crown.
Hmm, You mean my iscar and the 11 degree crown I have been doing is a waste?
The Dunning-Kruger effect is alive and well.
If you read Pope's work you will find one part where he sliced the muzzle at something like 20 deg and it only changed poi slightly, no group change. And that was with cast bullets.
It would be interesting to see what those same experiments would do at longer ranges.
The Dunning-Kruger effect is alive and well.
I hacksawed a barrel once then faced it off with a flat file and lightly touched the bore with a coned shape dremmel. It shot as good or better than the factory crown job.
Dave
Yup.
This is all the barrel did today...
Keep in mind, this is a 7 lb. rifle with a 2-7x scope on it.
Attachment 5915
I remember reading an overview of the experiences gained in "The Secrets of the Houston Warehouse" by David Scott
https://precisionrifleblog.com/2013/...ifle-accuracy/
where Virgil King stated that for a 6ppc, the barrel "must be 21 3/4 inches long for maximum accuracy".
Since barrel length has everything to do with harmonics, and some of us use harmonic tuners just for that reason, it's not inconceivable that you hit upon a better harmonic than the factory length barrel by cutting and crowning your barrels. In the end, I am a firm believer that anything you do to improve your confidence in yourself or equipment is probably well worth the effort expended and will benefit and add to your shooting skills.
For entire article go here: http://www.angelfire.com/ma3/max357/houston.html
Edit: I just re-read the above full article and would like to correct the 21 3/4" reference. That length of barrel did not apply just to the 22PPC, it applied to all the calibers he tested, .22, 6mm, and 30 cal.
Every barrel he had made was cut to 21 3/4 inch and target crowned. Didn't matter what contour, it had to be 21 3/4 inch, and setting back a barrel to gain some life ruined the length requirement and would never shoot as well.
Banning a gun will not solve what is a mental health crisis inflamed by incendiary rhetoric on social and television media. The first amendment in this case is less precious and more likely the causal factor than the second amendment.
This^
And even though 3/3 have improved, statistically speaking, it’s not enough to categorically claim it’s the road to a more accurate firearm. I’m using that term “accurate” in a very generic definition. With precision vs accuracy being two independent characteristicss.
But if it works, I would keep on keeping on.
Hmmmm? Where do I start? I’ll keep this short.
Regardless of brand of barrel. Factory or custom.
I’ve seen crowns that where poorly done and actually shoot pretty good. I’ll say this is more luck than anything else. Also damage to the muzzles crown from improper cleaning. Some seem to effect accuracy and some not as much.
I’ve seen crowns and have fixed muzzle crowns where you couldn’t even see the damage with the naked eye where the edge of the crown on one land and one groove had a nick to it and the rifle wouldn’t shoot any better than 1 1/4” groups at a 100 yards. Properly recrown the barrel and the gun would go to shooting 1/3moa groups or less.
Last comment....the muzzle crown is the last thing the bullet sees/touches when leaving the barrel. Any damage to the crown can and usually does have a negative impact on accuracy.
First question you need to ask yourself is....”What is my accuracy requirement?”
Later, Frank
Bartlein Barrels
Good to know that somehow, with absolutely no training, I can't damage a crown any worse than the factory has.ast comment....the muzzle crown is the last thing the bullet sees/touches when leaving the barrel. Any damage to the crown can and usually does have a negative impact on accuracy.
I have really only damaged one barrel crown- bad enough that it could be easily seen. I cleaned it up the best i could and went and shot it. I was expecting it to not shoot as good but it didn't have any measurable effect on groups. I figured I had gotten lucky and kind of forgot about it. The next time I shot the rifle I used my other load (one was for varmint hunting and the other was a heavier target bullet) and my groups were pretty poor. The rifle had shot both groups very good before- so the damaged crown bothered one bullet but not the other. I had the crown re-cut and it went back to normal- so it definitely can be a issue. I'm still not to the point that i worry about a brush getting pulled back into the barrel every so often....
In my case the barrel still shot flat base bullets excellent but the boat-tailed bullets shot poor. I don't know if it was the gas escaping around them that did it- or the way the bullet shape had it last contacting the barrel. Have you shot different bullet shapes through yours after you re-crowned it?
It’s not just the brush but the hard carbon particles that can lay in the bristles of the brush. The hard carbon particles will scratch the bore more so than the brush. That being said if I use a brush I never pull it back over the crown.
Also you get a gas cutting effect when the bullet leaves the barrel. This alone after X amount of rounds can wear the crown. This is why I don’t like a flat/sharp crown edge. We cut a 60 degree chamfer on the edge of the bore. Feel this helps the crown hold up better overall. Ever look at a M1 Garand barrel? 1903? M14 and even on the Gov’t test barrel drawings they all call out a chamfer on the edge of the bore. Some where at some point in time someone figured out something here years ago!
Flat base bullets I’ll say are more forgiving then boat tails are but boat tail helps b.c.
Bookmarks