Help! 22 hornet in savage mod 40

**henry1** · 01-31-2014, 08:38 AM

plinkin, boots and froggy, thanks for the input guys! I ended up having to work late last night and by the time i was off true value had closed! lol so hopefully today i will be able to stop by. fighting a cold as well. but TGIF! haha thanks again guys!
ill keep you updated!
Henry.

**bootsmcguire** · 01-31-2014, 10:38 AM

Originally Posted by plinkin

Irwin & Hanson are both owned by American Tool as is Vice Grip and they make tools for Snap On as well as Mac, Matco, Cornwell, SK etc.

I knew Irwin made Vice-Grip but didn't know about the others. Thanks, good to know.

**plinkin** · 01-31-2014, 02:13 PM

I used to have a mobile tool route between 1999-2004.

**henry1** · 01-31-2014, 08:58 PM

so so far i have bought a master mechanic no 3 and no 5 (which i have no problem owning, these things always come in handy) but True Value is currently out of no 4! Which it turns out is most likely the one i need! Ha! To town tomorrow again to see if ace has one....

**bootsmcguire** · 01-31-2014, 09:51 PM

Originally Posted by henry1

so so far i have bought a master mechanic no 3 and no 5 (which i have no problem owning, these things always come in handy) but True Value is currently out of no 4! Which it turns out is most likely the one i need! Ha! To town tomorrow again to see if ace has one....

Always the way ain't it. I had to get some 1/2 NPT galvanize pipe nipples and a 90* end to install my new shower/tub spigot this week. Experience has taught me that at about $1.50 each its cheaper to buy several lengths of varying lengths rather than pay the gas to go back when you "thought" you had the right one. Nothing you can do when they are out of that one size you need, no matter what it is. Good luck.

**henry1** · 02-01-2014, 06:31 PM

thats the truth! I messed around with it for a while today, used the smaller one, cut it down so that it wouldnt protrude into the bore, then couldnt find a socket that would fit it! GRRR! its in between a 5 and a 6 mm.... and in between a 1/4 and a 7/32 any sugestions? i dont have any 12pt sockets avail right now otherwise i would try that! haha, havn't tried to go to town yet either!

**henry1** · 02-01-2014, 09:32 PM

update! I got the sticky son of a gun out! ended up over at a buddies house tacked a socket on the ez out with his wire feed and it came right out! So happy! Now to find someone to ackley it for me! Thanks again guys! I appreciate all of your input and help! glad i got it!
Henry.

**plinkin** · 02-02-2014, 12:32 AM

Originally Posted by henry1

update! I got the sticky son of a gun out! ended up over at a buddies house tacked a socket on the ez out with his wire feed and it came right out! So happy! Now to find someone to ackley it for me! Thanks again guys! I appreciate all of your input and help! glad i got it!
Henry.

Is going to a 22AH what you really want or were you just frustrated with the Hornet case being stuck?

**henry1** · 02-02-2014, 12:27 PM

um no, i have always wanted to ackley it, it helps especially with the little hornet case. I wont ever push the hornet hard just because its so fragile of a case, some brass i have now is on its 2-3 firing and its coming apart. I might be able to double my case life when its ackleyd. its also my cheapest rifle to shoot, even cheaper than buying 22 ammo well almost. I can roughly, get at least 800 rounds out of a lb of powder. However i haven't loaded that many yet in my lifetime! haha.

**short round** · 02-06-2014, 04:35 AM

Congrats on getting the brass out. One thing to do to prevent case seperation is to make a

Congrats on fixing your problem. One thing to do on hornet brass, is to make an L shaped pick, use it to feel around on the inside of the case, near the bottom, if you feel a groove that brass is about to separate.