Neck tension can do that.
Dean
So I just started reloading, and went out this morning to test out some loads and try to find my max load. I guess I will list out the components I am using and the processes I used to load them.
Winchester once fired brass
CCI 250 Primer, only primers I could find and my friend checked his Speer book and they called for a magnum primer for 2520
Accurate 2520 powder
Sierra 165 Grain Game King Soft Point Boat Tail
Full length resized and deprimed using Hornady spray lube
Trimmed to 2.006", Chamferred and deburred
Tumbled in crushed walnut and nu polish and a touch of mineral spirits
Charged to exact by hand with a scale and a trickler
Bullets seated to .020" off the lands, No crimp
So I went and shot some this morning and got flattening primers way before I expected. I am using the Lee 2nd edition book, and they show a minimum load of 42.9 grains and a max of 47.7, so I started at 43 and increased in .5 grain increments. 43 grains shows no primer deformation, 43.5 I could tell the primer changed a bit but just barely, and 44 grains I got a flattened out primer...
43 Grains
43.5 Grains, Inconsistent flattening
44 Grains, flat...
I don't have any ejector indenting or stiff bolt lift, the only other thing I can see is a mark where the ejector appears to scrape on the head maybe when lifting the bolt? Picture #3 kinda shows it. Is this something I need to watch for as well?
So at what point do you start backing off? I felt like the 43.5 grain is probably the max. It just seems weird that I am getting pressure signs a half grain above minimum. I will probably load up 10 rounds each of some lower charges to try for accuracy but then I will be under the book minimum... I have since found some CCI 200 primers, should I try them and see how it goes? Just looking for ideas, again I am totally new to this so I just want to make sure I am being safe and gonna get the best BANG for my efforts. Thanks in advance for your guys' consideration.
Neck tension can do that.
Dean
RUMs are like woman in Stiletto heals, you know they are going to put you in the poor house, but that has never stopped anyone from pursuing them.
I should have mentioned. I am using lee dies and getting about .002" neck tension.
Also is it they original barrel or has it been swapped.
Dean
RUMs are like woman in Stiletto heals, you know they are going to put you in the poor house, but that has never stopped anyone from pursuing them.
Again, sorry for leaving stuff out.
Stephens 200 in .308 Win
Original barrel
Pretty much a new gun. Never been messed with.
Dean - Couldn't too much head space also cause this?
Another tidbit of info, factory ammo didn't seem to flatten them out. And I shot one round through my friends savage 11 and it showed up about the same if not a little worse. His left an ejector mark. He just looked in his Speer manual and they show a starting load of 41 grains and a max of 45... Maybe lee's book is a bit hot?
Accurate lists AA2520 with 165 SIE SBT Min 42.9 and Max 47.7 exactly the same as Lee.
Sierra manual #V-- 6th printing lists Min. 36.3 to a max of 42.7 with that bullet and AA2520.
Doesn't look "too flat" to me at all. Also I don't see any marks on the head of the brass from hard extraction.
If there is plenty of space left in the cartridge, you should probably try a slower powder. Hodgdon Varget is working good for me. AA 2520 lists as #96 on the powder burn rate table and Varget is #99 so they "should" not be that far apart. But I am shooting a heavier bullet and "needed" a slower powder....
The Varget load is listed as 42-46C gr at 2582 - 2773fps with a 65gr bullet
The fastest load listed is with CFE 223 at 45.4 to 48.3gr and 2649 - 2839 fps
This is on the Hodgdon reloading website which of course does not list other powders...
I would love to load up some varget. But there is someone that hits our local Walmart everytime they get a shipment and buys all of it. I was in there a couple weeks ago and they actually had some powder. The clerk and I were shooting the breeze and he mentions that they got in 12 lbs of varget that same day. He says its like the guy knows their shipments. They don't even know when it will come in, but this guy shows up 15 minutes after a shipment comes in and buys all the varget, one other powder, and he brings friends and wipes out the 9mm and 223 ammo... I couldn't believe they had 12 lbs at 2 o clock and when I got there after work they were out. I guess he was there at 2:15 and wiped it all out... So frustrating.
Last edited by thomae; 01-02-2014 at 10:27 AM. Reason: just making it family friendly
So it sounds like the lee book is on the high end of the spectrum. I know Sierra can be a bit conservative, but at least I won't be under a book minimum.
So I guess I will load some up in the 41-43.5 grain range and see how they group.
I hope to get a chronograph some day to see how fast I am actually shooting but for now I will have to shoot my drops and calculate it off of that.
RUMs are like woman in Stiletto heals, you know they are going to put you in the poor house, but that has never stopped anyone from pursuing them.
I would say that 44gr is where I would have some concern.
Would go with standard LR primers. IMR 4064, Varget, Reloader seem to be some of the best powders for the .308
Last edited by wbm; 07-29-2013 at 02:38 PM.
I have been told that some primers have harder cups than others. I know from personal experience that at least one lot of primers was too hard for my S&W Model 64, so I accept the information as likely to be valid.
A primer brand softer cups will show signs of flattening earlier than other other brands with harder cups.
Ok. I am not gonna give up on what I have already started but I got some info on another forum. The earlier Accurate data indicated 45 grains as a max load, and take away a grain or so for the magnum primer and that sounds about right.
But on your recommendation I put together some loads with Accurate 4064 that I have. With CCI 200 primers. I also have some IMR 4895 that I may try if I dont get results. I would love to try Varget. Just need to find some...
Got some Accurate 4064 last month. Have never used it before but the from the load data it looks to be just a wee bit faster than the IMR but that could just be from lot variations. Reloader 15 is also one you might give a go. Anyway hope you get it shooting like you want.
to my eyes....the primer doesnt show the firing pin indentation to be blown out at all..or at least not enuff to red flag the load charge.
chrono,s gonna tell the story.
Life is tuff.....its even tuffer when your stupid
{John Wayne}
http://www.reloadbench.com/burn.html
From looking at this, AA2520 comes in slower than 4064 powders. But Reloader 15 is a few steps slower, again, I would love to find some... I have 3 pounds of H1000 that I bought for my friends but 3 months later none of them have bought dies or brass or bullets so I am gonna try to trade some locally for some Varget or Reloader 15.
Life is tuff.....its even tuffer when your stupid
{John Wayne}
I think so too. H1000 seems to be just as hard to find as Varget. I just got lucky one day. But I don't own a magnum and none of my friends wanna get of their arse to get their act together so if I can trade it I will. They can go hunt up their own powder. I can't wait to get a load figured out so I can start playing. I am not terribly patient and this process is proving difficult for me. I just wanna go take a poke at the 1000 yard target on the hill. But it'll have to wait til I find a good load and get some drop data formulated.
Life is tuff.....its even tuffer when your stupid
{John Wayne}
Bookmarks