Can you post a picture?
My father-in-law gave me his old Stevens rifle in .308 a few days ago. The barrel only reads "Stevens". I'm not sure if this is a 200; how can I tell? Also, I'm looking for tips on how to re-finish the metal. Basically, I'm looking for the most efficient way to achieve a flat black look. Also, will the bolt handles for the Savage 110 fit this one?
Last edited by concepthomes1; 07-17-2013 at 09:18 PM.
Can you post a picture?
I've never seen a Stevens bolt action that wasn't a 200
I think that's the only model they make
may be a Stevens barrel on a Savage though.....
krylon comes in flat black
finish -blue the metal 1st
110 bolt handles will fit
welcome to SS
Last edited by Willoughby; 07-17-2013 at 07:02 PM.
The gun has been in its current configuration since the mid 1980's. The barrel is stamped Stevens then it says Series K just above the caliber .308 WIN
Sent from my over-rated Motorola cell phone with a poorly serviced AT&T plan.
There are no restrictions for you to post pictures. Send the photos to me and I will post them.
Is it a bolt gun?
Read this, then try to post your own pictures. http://www.savageshooters.com/showth...man-can-do-it!
Maybe try posting a pic of the entire gun, could help.
Full gun pic up
Sent from my Xoom using Tapatalk 2
http://www.youtube.com/results?searc...c..11.youtube.
You have a mod 200 with a wood monte carlo stock. That's better than a new mod 200. Check youtube for instructions on bluing.
Last edited by Mach2; 07-18-2013 at 01:08 AM.
That is not a Steven 200. It is a Stevens 110 series K made in the 80's. I'll bet it has a E prefix on the serial#. I can tell the age by the bolt handle and bas.
For all practical purposes, it is a long action stagger feed, same as a lot of Stevens 200's. Stevens 200 never came with a wood stock.
"As long as there's lead in the air....there's still hope.."
The only way to be sure is measure the action screw spacing. It's either 4.522" (first generation short action) or 5.062" ,depending on when it was made.
"As long as there's lead in the air....there's still hope.."
How's the trigger? Was it ever worked on? I'd be curious what the pull is from an 80s Stevens. Whuts the barrel length?
I took my Stevens 200 in .270 and put a monte carlo wood stock on it with riflebasix trigger. Shes pretty.
Thanks for the thread. Id never seen the older Stevens before. If you get a chance I hope youll post some closeups.
Looks like the iron sighted Savage Hog Hunter.
Barrel length is 22". Action screw spacing is 4.5" so Short Action. Trigger has never been worked on to my knowledge and it doesn't appear to have been. Not sure of poundage on trigger break but it is extremely smooth and has ZERO creep. I just apply some light pressure and it breaks clean.
Last edited by concepthomes1; 07-20-2013 at 03:20 PM.
Thanks for the fototour. I suppose the most obvious difference in the 80s Stevens is the flat rear receiver top. There re some minor differences in the trigger spring mechanism. The wood stevens stock is a nice advantage of the older rifles. You can't just go out and buy that wood stock today. It makes your Stevens unique in a way.
You may have a pre lawyer trigger since you have a nice low pull.
One of my fav tools is a trigger gauge. I use it not just to set a low trigger pull but to set all my triggers at the same pull. Knowing the pull weight is like knowing the 1/4 mile time on a sports car.
You have one of the nice old multi-screw triggers, which has quite a bit of adjustment capability for both trigger pull and sear adjustment (I think there is a discussion about this in the Tech section). An easy mod is to replace the "heavy" trigger spring with lighter wire; send my your info and I will send you a piece if you are interested.
Bump
If youre still there. Have you tested the rifle to see how it groups? I can see in the foto that the stock has no pillars. I was curious how well pre pillared wood stocks grouped. The pillar bedding was a simple but major advancement that most all manufacturers utilize now. Pillar bedding is so effective that it has basically rendered moot most bondo and epoxy bedding methods.
Still here. I've got a few threads showing my progress. Next step is the Duracoat on the action and barrel. Also going to refinish the stock before reassemble. My plan is to have the rifle ready to shoot by Oct 1, then sight in for hunting season on Nov 15.
Sent from my Xoom using Tapatalk 2
Bookmarks