ss has a good trigger replacement save your old one and replace it if you sell the rifle later.
bob
Hoping to find some help in lowering the pull weight on my 112BVSS with acutrigger. Best I can get is 2.375 lbs. Doing long range work and really need to get to 1lb or less. I know there are many aftermarket options but am trying to save a buck here. Thanks, smoker
ss has a good trigger replacement save your old one and replace it if you sell the rifle later.
bob
Thanks Bob, looking for something used.
Yup dont think it is going to happen, if you want a trigger lighter than 1 lbs you need to go the aftermarket route.Originally Posted by smoker
Look at rifle basix, I have the SAV-1 trigger at its lowest setting (around 1lbs) and it is the most crisp trigger I have ever used, I have it perfectly adjusted with no creep or overtravel and it is perfectly safe.
Kind of a shot in the dark. Dropped a bundle on the rifle and optics. Trigger sure shows up ~20X
If you don't wish to spend the money on an aftermarket trigger, try pulling the trigger apart and then shim and/or polish (as appropriate) all the moving contact surfaces. You may not change the actual pull weight very much, but the "feel" of the trigger can be improved a great deal.
In a good trigger, pull weight is only one of several factors.
Trigger is actually very nice...very smooth, little to no creep, breaks clean with no overtravel, couldn't ask for more, but like I said at 20 power as you apply pressure you can watch the crosshairs walk right off the bulls eye. Guess I'll have to bite the bullet and go for a rifle basix or similar. Thanks for your input. smoker
Pull the spring for the trigger and replace it with one from the target trigger version. Or just pull your current spring and cut very small increments off until it is light enough.
More shooting, less typing.
Great Jamie!!! Thats what I was looking for. The target spring would be the best approach but I can cut 1/4 to 1/2 of a coil at a time....right? I have a trigger pull gauge so checking will be easy. Thanks much smoker
Well there is a couple of small problems with this. First Savage will not sell springs, so the only place that I know of that sells them is SSS, and that is IF they have gotten any parts from Savage. Second the target accu-trigger uses the SAME silver spring as your varminter gun, (BVSS) so you will not gain a thing. The lower trigger weight comes from a special sear, that is identified by a small dimple under the flag. Savage will not sell anyone a target accu-trigger sear, including SSS.Originally Posted by smoker
Cutting coils can be fine, but watch how much you take there has been a few on this site that cut too much, and rendered themselfs with a useless gun. Remember I said savage will not sell springs? Guess what these foaks had to do, either buy a new spring from SSS, or ship their rifle back to Savage and pay them to put a new spring in.
Thanks for the advice 82boy. Well I guess if I take too any oils off then I'll have to go for a new trigger, which I was just about to do when I read Jamie's post. I'll let you know how I make out. smoker
Down to 1.250 lbs....think I'll quit. Toke ~ 1.5 coils 1/4 coil at a time. Repeats +/- 1/8 lbs. I had it out of the stock to begin with .....having it shortened, so a perfect time to monkey with it. Thanks again to all. smoker
My target trigger came set to 1 pound 4 oz. It is all I want so far. I heard it will take a set all the way down to .5 pounds. Any body know if that is true?Originally Posted by smoker
Does anybody know what Savage would charge to install the "Target" sear for him?
Thanks,
John
The target accu-trigger is advertise to go down to 6oz, but I have yet to see one that will go that low, and 2 function at weights under 1 lbs.
No Savage will not install the target accu-trigger on guns. They put the big warning on the target accu-trigger guns, for liability reasons, and they will not put one on anything that doesn't have their warning.
I got my factory triggers down to around six oz just playing with them, it can be done
Patrick,Originally Posted by 82boy
Thank you for the info. You have been a lot of help to many of us.
John
Shtr,Originally Posted by lrpv-shooter
You experience seems more reasonable and is what I would expect. Taking no issue with Patrick, understand.
Can you share how you "played" with your triggers. I expect I would like to lower mine in the future.
I really like the "safety trigger" on my Savage. At first I thought it gimmicky but I have seen the light. The thing simply can't "bump" or "slam" fire. That has always been a source of heartburn with me when setting up a trigger.
Must be a really good reason why people with known good sense are removing their Accutriggers and replacing them with spendy aftermarket items.
Thanks,
John
I think someone should check their target spring with a magnet and some calipers. Post the material, wire diameter, inside, outside and overall length and the coils per inch. then someone could go to a place like this...
http://www.leespring.com/compression...forWhat=Search
or
http://www.springsfast.com/compression-springs.php
and buy a minimum of like dimensions.
OAL can be fudged...preload for one that is close can be dealt with. To go lighter within a wire diameter and OD/ID specs just increase the coils per inch....heavier is fewer coils per inch.
Then all can have a light spring for around 5 bucks with shipping.
Originally Posted by stangfishOriginally Posted by 82boy
Thanks I read that the other day and forgot about it. So the latter part of my post addresses a lighter spring.....is that an option? I dont have a dog in this hunt as I have no Accutrigger.Originally Posted by 82boy
[quote=stangfish So the latter part of my post addresses a lighter spring.....is that an option? [/quote]
A lighter spring can be abtained, with good results, but the target accu-trigger uses the same spring as the varmint spring. (Silver.) The reduced weight comes from the special sear. A custom spring is easier than you think, just look at you ink pen.
I need pikters!
This one is a ?
http://www.gunblast.com/images/Savage-12F/DSC01286.jpg
Probably copywrited so I linked to it.
That is a target accu-trigger with a silver spring, if you look on the other side of the sear you will see a small dimple identifing it as a target accu-trigger sear.
When you manipulate a savage trigger a little goes a long way so if you cut the spring I would cut a 1/4 coil till you get close then I went 1/8 coil till it was what I wanted plus I noticed the trigger pull changed from out of stock to in stock so I removed and reinstalled the stock a couple of times. My triggers have been as low as 3.5 oz but that's to light I think...
I will try and post some pics soon
Bookmarks