Recrowning Savage barrels

[Newtosavage]

Possibly that’s just how I read those statements. I’m glad things are working out well for you in the accuracy department.

Thanks. I was never claiming that hand crowning was the answer. Only sharing my experience. I would say however that anyone considering chopping their own factory Savage barrel, shouldn't be afraid to give it a go.

[Shortbox4x4]

Hmmmm? Where do I start? I’ll keep this short.

Regardless of brand of barrel. Factory or custom.

I’ve seen crowns that where poorly done and actually shoot pretty good. I’ll say this is more luck than anything else. Also damage to the muzzles crown from improper cleaning. Some seem to effect accuracy and some not as much.

I’ve seen crowns and have fixed muzzle crowns where you couldn’t even see the damage with the naked eye where the edge of the crown on one land and one groove had a nick to it and the rifle wouldn’t shoot any better than 1 1/4” groups at a 100 yards. Properly recrown the barrel and the gun would go to shooting 1/3moa groups or less.

Last comment....the muzzle crown is the last thing the bullet sees/touches when leaving the barrel. Any damage to the crown can and usually does have a negative impact on accuracy.

First question you need to ask yourself is....”What is my accuracy requirement?”

Later, Frank
Bartlein Barrels

[Newtosavage]

ast comment....the muzzle crown is the last thing the bullet sees/touches when leaving the barrel. Any damage to the crown can and usually does have a negative impact on accuracy.

Good to know that somehow, with absolutely no training, I can't damage a crown any worse than the factory has.

[Whynot]

I have really only damaged one barrel crown- bad enough that it could be easily seen. I cleaned it up the best i could and went and shot it. I was expecting it to not shoot as good but it didn't have any measurable effect on groups. I figured I had gotten lucky and kind of forgot about it. The next time I shot the rifle I used my other load (one was for varmint hunting and the other was a heavier target bullet) and my groups were pretty poor. The rifle had shot both groups very good before- so the damaged crown bothered one bullet but not the other. I had the crown re-cut and it went back to normal- so it definitely can be a issue. I'm still not to the point that i worry about a brush getting pulled back into the barrel every so often....

In my case the barrel still shot flat base bullets excellent but the boat-tailed bullets shot poor. I don't know if it was the gas escaping around them that did it- or the way the bullet shape had it last contacting the barrel. Have you shot different bullet shapes through yours after you re-crowned it?

[Newtosavage]

I have really only damaged one barrel crown- bad enough that it could be easily seen. I cleaned it up the best i could and went and shot it. I was expecting it to not shoot as good but it didn't have any measurable effect on groups. I figured I had gotten lucky and kind of forgot about it. The next time I shot the rifle I used my other load (one was for varmint hunting and the other was a heavier target bullet) and my groups were pretty poor. The rifle had shot both groups very good before- so the damaged crown bothered one bullet but not the other. I had the crown re-cut and it went back to normal- so it definitely can be a issue. I'm still not to the point that i worry about a brush getting pulled back into the barrel every so often....

In my case the barrel still shot flat base bullets excellent but the boat-tailed bullets shot poor. I don't know if it was the gas escaping around them that did it- or the way the bullet shape had it last contacting the barrel. Have you shot different bullet shapes through yours after you re-crowned it?

No, I can't say I've tried that.

[Shortbox4x4]

I have really only damaged one barrel crown- bad enough that it could be easily seen. I cleaned it up the best i could and went and shot it. I was expecting it to not shoot as good but it didn't have any measurable effect on groups. I figured I had gotten lucky and kind of forgot about it. The next time I shot the rifle I used my other load (one was for varmint hunting and the other was a heavier target bullet) and my groups were pretty poor. The rifle had shot both groups very good before- so the damaged crown bothered one bullet but not the other. I had the crown re-cut and it went back to normal- so it definitely can be a issue. I'm still not to the point that i worry about a brush getting pulled back into the barrel every so often....

In my case the barrel still shot flat base bullets excellent but the boat-tailed bullets shot poor. I don't know if it was the gas escaping around them that did it- or the way the bullet shape had it last contacting the barrel. Have you shot different bullet shapes through yours after you re-crowned it?

It’s not just the brush but the hard carbon particles that can lay in the bristles of the brush. The hard carbon particles will scratch the bore more so than the brush. That being said if I use a brush I never pull it back over the crown.

Also you get a gas cutting effect when the bullet leaves the barrel. This alone after X amount of rounds can wear the crown. This is why I don’t like a flat/sharp crown edge. We cut a 60 degree chamfer on the edge of the bore. Feel this helps the crown hold up better overall. Ever look at a M1 Garand barrel? 1903? M14 and even on the Gov’t test barrel drawings they all call out a chamfer on the edge of the bore. Some where at some point in time someone figured out something here years ago!

Flat base bullets I’ll say are more forgiving then boat tails are but boat tail helps b.c.

[gbflyer]

It’s not just the brush but the hard carbon particles that can lay in the bristles of the brush. The hard carbon particles will scratch the bore more so than the brush. That being said if I use a brush I never pull it back over the crown.

Also you get a gas cutting effect when the bullet leaves the barrel. This alone after X amount of rounds can wear the crown. This is why I don’t like a flat/sharp crown edge. We cut a 60 degree chamfer on the edge of the bore. Feel this helps the crown hold up better overall. Ever look at a M1 Garand barrel? 1903? M14 and even on the Gov’t test barrel drawings they all call out a chamfer on the edge of the bore. Some where at some point in time someone figured out something here years ago!

Flat base bullets I’ll say are more forgiving then boat tails are but boat tail helps b.c.

Agree. Plus, it takes literally seconds when that piloted 60 degree center tool goes in and the setup is a snap.

[JeepsAndGuns]

If you want to know if it is your crown job or the shortening of the barrel that is making the accuracy improvements, take a factory barrel and only trim off like 1/4 inch or so then recrown like you have been.
If accuracy improves, then you might be on to something. If nothing changes, then it is the barrel being shorter and stiffer that helped them.

[Shortbox4x4]

Good to know that somehow, with absolutely no training, I can't damage a crown any worse than the factory has.

Most factory type rifles/guns as a good ball park number.....the cost for them to make the barrel and this includes the cost of the steel, contouring, chamber, threading, crowning etc...I’ll throw a number of $60-$100. Some makers do put a little more time and effort into the barrels and will have more cost into them.

I don’t know how to post pictures here (think I have to pay a fee) but I have pictures of factory barrels where the centerline of the bore of the barrel isn’t even in the center of the barrel blank. It’s not a Savage either but is a factory barrel.