Good Thumb Hole Target Stock

[RC20]

The stock got its first workout today. Overall I like it a lot.

One issue is my ear muffs bump into the far side cheek riser. The BTH on the other gun is thinner there. I will think about having my brother mill it down, see what he says, not sure I want to risk the finish and I can and did adjust.

The two Thumbhold are shooting neck and neck, says a lot for the Boyds that came on the 111as that is not pillared.

The 111 Boyds has the less capable scope, maybe e better barrel. the 12FV has both the more capable scope and stock (not just pillared, its heavier and more solid)

I like them both. I can tell when I am shooting better as both respond. Definitely a the right move.

I certainly endorse the EABH stock. If there is any question the pillars are a plus, good pad on back, well formed and better than the 111 BTH (Boyds may have better stocks than what came on it, but again its doing real well too)

[RC20]

I will add some more into this.

I am getting some wild shots, so the first step was to greased the bottom of the receiver and make sure it was free floating. Contact in a lot of places, so milled down with the old dremel tool.

I am not saying that's the issue but it removes on possibility, erratic enough that it was that or the scope (rest is good).

I would prefer a bit more wood removal than less for a Pillar bed type stock but not all that bad to get done and not a lot removal needed. About 6 times in and out.

It has to be tough to get it all right.

[RC20]

I have done the grease and remove and mill down, I think I have it fully free floating.

One bugger was as I got it milled down, the trigger started to act up (lock up)

That was traced to contact at the very rear of the trigger by the adjustment screw with the stock.

A bit more milling and back to normal.

Count on a bit of work to get it right. Very nice stock, not perfect as is though. Takes some wood work to get it right.

My BTH111 has had none of those problems but its the original stock and may have better setup from the factory for Savage and to their specs.

[jpx2rk]

Mind listing what tools are needed/suggested to get either the Boyd's or the EAB stocks to fit the FV12's. I've got twins in 223 & 204R, so I'm thinking something like this could be a good winter project for me to try. One of the Boyd's and one of the EAB's so I could tell the twins apart without having to look at the barrel to see the caliber I'm dealing with.

[RC20]

I don't mind a bit.

First: I was in a hurry so I ordered the Varmint contour which is available vs the Bull which is a can get but there is a wait time. If I had the time (or was patient) I would have ordered it for the bull profile as that what is on it now. Not a big deal but you have to sand out the barrel channel and widen it a bit (I used sand paper warped and taped to a dowel , and went with heavy sand paper as it takes some elbow breast, used a gun vice to hold it. ) More better to be patient though I did a pencil barrel stock from that to Bull profile as well doing it the same way, no choice there as used and I knew I would have to.

I like the dowel as I can move it up and down the channel easily and where needed.

Other than that we have a Dremel tool and I used the various type of sanders and reamers to work on the areas that were in contact. Wood scrape may work but I don't have those. and m

For grease I used Honady neck lube. Put it on the Action, put action in stock, tighten down screw's, remove - wipe the excess grease off the stock and the wood shows a dark spot. Sand or mill it and then repeat until clear.

The only one I missed is not the tank but the back of the trigger itself rested on the ledge and it took me a while to find out where it was binding.

Trigger got erratic and ok when rear loosened but did not think they would not have that cut out good as its a zero support area and more is better and hurts nothing.

[Texas10]

The EAB comes with pillars installed. You'll need a new trigger guard as the 12FV trigger guard will not fit the stock. Stocky's I think sells the them, as well as Boyds. You can get it from Savage too, usually cheaper, but you'll need to know the part number. Unfortunately I don't have it off the top of my head, but it's the same as my 12BVSS only black instead of SS.

I bedded mine with Devcon 10110 and that helped a bit with consistency. Also free floating the rear tang. It should not touch the stock.

And finally, torque tuning the rear action screw will help tighten your groups.

To open a barrel channel I use deep sockets from my tool box. Find one that is the right size and wrap some 80 grit around it, work my way to 220 grit. About 20 minutes work is all. When done, rub some stock finish on the raw wood.

[RC20]

I add in what I hope is the last cfhapter on this.

I felt some movment and on checking, the whole assembly was rocking off the rar screw. ????????

re greased it and miner contact but not enough to epalin, make sure lug was clae.

Finaly got it down to the front acion screw, turned it upsudie down and the pillar in the stock was moving up and donw!

I put a washer on the top, still moving up and down.

I built a shim out of a .045 washer and put it in first then the pillar through it, now its solid.

Miner grease contact to clean up but again nothing major.

still trying to wrap my mind around it. I can see the thread and pillar bottoming out, but the washer on top should have done it, moved it up but sill flexed the same.

Will take it but annoyed. Shouldn't;t have to screw with it that much. Boyds is better and its a cheaper stock.

[Robinhood]

Intriguing and fascinating at the same time.

[Texas10]

If I am reading correctly, the action, pillar and screw were tight to each other but moving within the stock. If the pillars in your stock are like mine, they have a shoulder and it seems the stock was counter-bored too deep for the shoulder on the pillar.

To fix this ( I had the same problem on my Richards Microfit, but planned on it) coat the action, screw and pillar with mold release, and put a bit of epoxy under the shoulder of the pillar and then install it and screw everything down tight and strap the action/barrel tightly to the stock. Once cured, you'll have custom fitted it to the stock. The pillar can still be removed if needed, but there'll be no more slop.

Washer on top would not eliminate the excess room under the shoulder, and that's why the shim under the pillar did work.

I hope this helps.

[RC20]

Thank you. I am still chewing on your answer, I have to try to get the visual picture.

From my take, when I tightened up the front action screw, the pillar contacted the receiver and the screw pillar were solid. The recess in the stock was too deep and it just floated. So the screw and pillar were tight to the receiver, but there was motion if you gripped the stock and barrel and did a hand grip thing pulling them together. I about ^&%$ when I saw the pillar moving up and down.

What I am still trying to get straight is the geometry aspect. I put the shim in, pulled the front down doing what supposed to tighten the front first. but that would seem to created a bind with the rear as its clear of the stock. No major contact even with shim in place. So its like it rotates in place, not on the same level plain.

On the other hand it did not feel like it, rear screw did not have any of the "give " feel. Just plain weird. Mental geometry is not my forte. I did good in it in high school so not hopelessly inept.

I am also still pretty pissed at EABCO. There are two aspects that should not be an issue, none of the parts should touch the stock on a pilar mount (unless you bed it) , period. I had contact all ujp and down the receiver that I removed. Excess clearance from factory is fine, not enough removed is not.

Add in the rear trigger mechanism touching and the issues that caused and its really poor quality control.

I don't know of Boyd's straight from them is better but it can't be worse. I have not done the whole drill on my BTH that came on the used Savage, but its solid and shoots good.

At this point I would say really nice quality stock and the fit sucks and be prepared to do some work if that's SOP from them.

I will probably have my brother bed the receiver now its setup correctly, he likes messing with that stuff

[RC20]

No free lunch, the throw out showed up where I was not looking for it, barrel hit the channel on the receiver end (two wood larger rings, one far out and one up close to the nut)

Geometry explained, felt solid cause the barrel was in solid contact with wood.

Found out at the range, huh. Ok, can't sand it down, need a shim, no metal stock and my one piece of plastic shattered

So I wound up with 3 pi3eces of 22 cardboard box stacked and that corrected it (for a while). Crushed of course and then went out

Worked long enough to get a couple of good groups with two different loads.

Just have to get metal shim and it should be good.