PDA

View Full Version : BAD BAD BAD BAD BAD ****UPDATE***



Pages : [1] 2

dwa
06-09-2011, 08:59 PM
FIRST AND FOREMOST I THINK THAT MY STOCK HAS ALOT OF TENSION IN IT. I DONT KNOW HOW BUT IT JUST SEEMS LIKE IT DOES AFTER I GOT IT BACK FROM BEDDING. TODAY I WAS MESSING WITH THE DAMN CENTERFEED MAG IN MY RIFLE. I CANT TIGHTEN THE REAR SCREW DOWN TO THE PROPERLY WITHOUT THE BOLT CYCLING EXTREMLY HARD. SO I TOOK THE STOCK OFF WENT TO WORK. I GOT THE MAG DOWN WHERE I THOUGHT IT NEEDED TO BE AND SLAPPED IT BACK TOGETHER. I WAS TRYING TO TIGHTEN THEM A LITTLE BACK AND FORTH AND TRYING TO KEEP THE BOLT CYCLING CLEAN. WELL SOME HOW I TIGHTENED THE FRONT SCREW SO THAT NOW THE BOLT WONT OPEN. NOT ONLY THAT THE HEAD STRIPPED WHEN TRYING TO BACK IT OUT.

SO WHAT DAMAGE COULD I HAVE DONE?
WHAT SIZE SCREWS DO I NEED TO CHANGE THESE CHEAP BASTARDS OUT?
HOW CAN I TELL IF THE STOCK IS UNDERSTRESS?
IF IT IS SHORT OF THROWING THIS THING OFF A CLIFF HOW DO I FIX IT?

r29l20
06-09-2011, 09:21 PM
Yes your action is under stress. You should be able to tighten the screws down tight and not change how the action sets in the stock. The screw size is 1/4-28. Did you loosen the rear screw first, that might help you get the front screw loose. Also make sure the front screw isn't to long, and binding on the bolt lug. Just steep back and take a deep breath, you didn't do anything that hasn't been done before. Who did the bedding? Maybe they bedded it without the L clip. Try putting it back together without it.You are among friends we'll try and get you through this. Good luck.

dwa
06-09-2011, 09:28 PM
A LOCAL GUY DID THE BEDDING. THE MAG WAS SHIMMED IN WITHOUT THE L CLIP. I TOOK THE REAR SCREW OUT AND THE FRONT STILL WONT BUDGE. I WILL HAVE TO TAP THE SRCEW AND REVERSE THREAD IT OUT I GUESS.

r29l20
06-09-2011, 09:38 PM
Give this a try, find a flat blade screw driver tip the quick change kind, that fits tight in the stripped out hole, tap the tip in so it sticks, then tap and turn at the same time. This has saved me countless times.

bootsmcguire
06-09-2011, 09:42 PM
If that doesn't work give this a try...

Use a dremel and a small diamond type stone and remove the head, then the stripped action screw's shank will be left and you can lift the barreled action out of the stock and just grab the screw's shank with vice grips and remove it. Takes some patience but it will work. I have removed quite a few bolts and screws that way.

Just an idea. May be easier depending on what tools you have available and may be less chance of stock and action damage?

dwa
06-09-2011, 09:54 PM
OK THANKS GUYS HEADED OUT TO THE BENCH.

dwa
06-09-2011, 10:37 PM
ALRIGHT GOT IT OFF. I HAD TO GO A DIFFERENT ROUTE THAT I DONT WANT TO TALK ABOUT. AS FAR AS THE SCREWS IS THAT BOTH AT THE SAME SIZE.

bootsmcguire
06-09-2011, 10:44 PM
Glad you got it out. Both are 1/4-28 I believe.

GaCop
06-10-2011, 06:46 AM
Correct, front is about 1 1/4" and the rear 1 1/2" I use the bolts from True Value or Ace Hardware. They're stronger than the factory bolts. I just had a rear factory action bolt shear the head at the shank last weekend. Now replaced with a good one from T.V.

dwa
06-10-2011, 07:44 AM
DO I NEED TO JUST TAKE THE RIFLE TO A DIFFERENT SMITH AND GET IT PILLAR BEDDED?

Blue Avenger
06-10-2011, 11:29 AM
http://img.photobucket.com/albums/v675/gcidso123/funny%20pic/capslock.png

dwa
06-10-2011, 12:16 PM
OR MR. GLOBAL MOD WITH YOUR "PHENOMENAL COSMIC POWERS" COULD ADD SOMETHING WORTH WHILE.

I AM A DRAFTER SO MY CAPS STAY ON ALL DAY AND LOOKS NORMAL TO ME. IT THEN BECOMES A HABIT. I HAVE TO CATCH MYSELF.....................to turn them off.

now do I need to pillar bed to relieve the stress in the action?

jpdown
06-10-2011, 12:27 PM
Sounds like after the bedding job the actions screws were just too long. Get some new 1/4 x 28 (fine thread) button head or socket head screws from the hardware store and attach the action screws until snug with the bolt removed. You can then see if/how far the action screws are protruding into the action. Remove action screws and trim till flush with bottom of action. That should fix the problem if the bedding job is sound. Pillar bedding will only help if there are signs the action screw heads are cutting into the wood/composite from the bottom side of the stock which might explain how they lengthened over time.

tammons
06-10-2011, 12:51 PM
Architect here and it took me a long time to adjust. Now it screws up my cad drafting as I am always
hitting the sHIFT kEY at the first of a sentence when working in cAD.

Mod he means no harm, besides I remember when typing in all caps was not considered rude.

Its stupid really. Caps are just caps. I spent 6 years in architectural school writing in caps before computers.



OR MR. GLOBAL MOD WITH YOUR "PHENOMENAL COSMIC POWERS" COULD ADD SOMETHING WORTH WHILE.

I AM A DRAFTER SO MY CAPS STAY ON ALL DAY AND LOOKS NORMAL TO ME. IT THEN BECOMES A HABIT. I HAVE TO CATCH MYSELF.....................to turn them off.

now do I need to pillar bed to relieve the stress in the action?

tammons
06-10-2011, 12:53 PM
Oh, back to the topic.

Your bolts are probably too long.
Also can happen when you change trigger guards.

memilanuk
06-10-2011, 01:34 PM
Some of the older Savage actions have the front action screw further forward than later models, and there isn't a whole lot of 'meat' in the receiver wall at that point for threads. After bedding (depending on how it was done) the 'smith may have found that the old screws were barely getting any 'bite' and made new ones. Or if he inletted things a little deeper than original when doing the bedding, it could even happen with the original stock bolts. At any rate, yes, its not un-common to either make new ones or if you have a grinder and a tap/die set, trim the old ones to fit.

Similar things can happen with scope base screws being too long and acting like a set-screw when you try and remove a barrel... DAMHIKT!

As for the capslock... thats been basic Netiquette 101 for a *long* time. When AOL users started migrating onto the WWW way back when, that was usually one of the give-aways that they were from AOL - chat/email there didn't care about caps lock - the rest of the world thought otherwise. Nowadays its usually older people who find the larger letters easier to read. I can see how someone who works in block-print all-capitals all day would find it tough to switch over. I gotta say... that picture is *dang* funny, IMO. Copied and saved and uploaded to my Photobucket account for use as needed!

Monte

dwa
06-10-2011, 02:11 PM
I got it figured out now. its the centerfeed mag. I was able to get it out since there wasnt much holding it in besides some shims. I put the new screws in and tightened the crap out of them and everything worked great. I must need to relieve the mag cut out in the stock. so when i tighten them the mag doesnt touch the bolt.

r29l20
06-10-2011, 03:34 PM
Good job pard, See I knew we'd get through it.

marcus40
06-10-2011, 06:36 PM
I have a recently purchased Savage Model 16 and it has 5/16" hex head screws, the manual calls for 40 inch-lbs of torque. I recently purchased a 1/4" Inch-Pound Torque wrench since I have a bad habit of over tightening stuff.
Just my 2 cents worth,
Marcus :)

Salvo
06-12-2011, 01:01 AM
Your bolts are probably too long.


That's what she said, last night.

When my front action screw got stuck and stripped out the screw head, I used a cutoff disk on a Moto-Tool to create a slot on the screw head. - Then I used a big slotted head screwdriver to remove the action screw.

I was going to replace the action screw once I got it out, but upon reflection, I decided that my home-made slotted-head screw was a lot better deal. - It's easier to tighten and to loosen, so why cough up extra bux for the same thing that failed in the first place?

Yes, I am cheap too, besides being the kind of guy who would strip out the head on an action screw.

My take on this is that Savage needs to pay a bit more attention to the action screws. Apparently I'm not the only fellow who got bit because the screw was a few silly millimeters too long.