Activity Stream - Savage Shooters

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles

Yesterday, 09:43 PM

PatrickBruce replied to a thread Adjusting safety screw after installing a lighter return spring in Axis Series Rifles

Both in and out. Same result. I thought maybe it was a stock issue since I have it in a Boyd's. But the results are...

5 replies | 100 view(s)

Yesterday, 08:20 PM

bearcatrp replied to a thread Extractor kit for my savage 110 FCP in 110-Series Rifles

Did have a primer blow out. It was from a loose primer pocket on a 4th time shot brass. I changed to a new bolt I...

14 replies | 480 view(s)

Yesterday, 08:20 PM

Robinhood replied to a thread Extractor kit for my savage 110 FCP in 110-Series Rifles

And lots of holes in the face from peirced primers. This is a Savagesmith issue. Nothing personal Bearcatrp, have...

14 replies | 480 view(s)

Yesterday, 08:04 PM

Robinhood replied to a thread Adjusting safety screw after installing a lighter return spring in Axis Series Rifles

The factory trigger return spring is adjustable. The Mcarbo is not. After watching Mcarbos vid on your kit. If your...

5 replies | 100 view(s)

Yesterday, 07:40 PM

sharpshooter replied to a thread Adjusting safety screw after installing a lighter return spring in Axis Series Rifles

Did you do all this testing out of the stock?

5 replies | 100 view(s)

Yesterday, 07:37 PM

sharpshooter replied to a thread Accutrigger adjustment problem on a Savage 11 in 110-Series Rifles

That trigger bracket is a transitional bracket. If you will notice there are 2 holes in the bracket to accept the old...

6 replies | 210 view(s)

Yesterday, 05:43 PM

PatrickBruce replied to a thread Adjusting safety screw after installing a lighter return spring in Axis Series Rifles

Ok. Thank you for the reply. One question though. The kit I installed has an over travel screw that the spring sits...

5 replies | 100 view(s)

Yesterday, 05:32 PM

charlie b replied to a thread Extractor kit for my savage 110 FCP in 110-Series Rifles

Do you mean the pin that retains the ejector? It can only come out one way. If punched hard the wrong way it might be...

14 replies | 480 view(s)

Yesterday, 05:29 PM

Robinhood replied to a thread Accutrigger adjustment problem on a Savage 11 in 110-Series Rifles

If you have the wrong hanger, the safety is an issue. The safety, pre accutrigger had a part that looks like a barbell...

6 replies | 210 view(s)

Yesterday, 05:14 PM

Robinhood replied to a thread Adjusting safety screw after installing a lighter return spring in Axis Series Rifles

It has been forever since I played with an Axis but here is my philosophy with the safety and trigge spring adjustment....

5 replies | 100 view(s)

Yesterday, 03:34 PM

J A XSP replied to a thread 400 Legend, anyone ? in Single-Shot Carbines, Rifles & Shotguns

Gerald, I've been curious, as well. I still haven't tried the 350 Legend and that's where I'd probably start. The only...

2 replies | 155 view(s)

Yesterday, 03:24 PM

J A XSP replied to a thread Contender 30-30 in Single-Shot Carbines, Rifles & Shotguns

I shoot the AI version but 125s are all I've used on deer. Central Texas deer tend to be small-bodied and I take does...

8 replies | 238 view(s)

Yesterday, 12:53 PM

PatrickBruce started a thread Adjusting safety screw after installing a lighter return spring in Axis Series Rifles

I have installed a MCarbo trigger kit recently and have run into a fun problem. I installed the 2.5lb spring and one of...

5 replies | 100 view(s)