Reply With QuoteUnderstanding that different guns accept different loads. I started at 92grs and worked up!
97 grs of H 4831 under the 225 Accubond shoots 2" at 500 yards so have never changed the load in my 19" barrel Striker.
Neal
What is your favorite 338 Edge Load?
Just wondering?
Getting ready to load some up!
[B][SIZE=3]Dennis[/SIZE][/B]
Understanding that different guns accept different loads. I started at 92grs and worked up!
97 grs of H 4831 under the 225 Accubond shoots 2" at 500 yards so have never changed the load in my 19" barrel Striker.
Neal
Im still working up mine up to 90 grains H1000 behind 300 SMK @ 3.780 OAL every thing looks fine had trouble with Chrono last time out not enough light but have not got any pressure signs yet but they group nice only got 25 rounds throught barrel but it is working out to be real nice rifle so far
I'm using 94-95g of H1000 behind a 300SMK with no pressure signs.
I think I'm using the older slower lot of H1000. When I start a new batch of powder, I'll drop back down and work up a new load.
"Muzzle velocity is a depreciating asset, not unlike a new car, but BC, like diamonds, is forever."-German A. Salazar
Anybody have a suggestion for Nossler 250gr Accu-Bonds?
[B][SIZE=3]Dennis[/SIZE][/B]
I know this is the wrong section for this, but what action are you guys building these .338's on
Long and short. It's a lot of work to get them to work as a repeater and they work great as a single shot. So, any action with a magnum bolt head will work.Originally Posted by Samdweezel05
"Muzzle velocity is a depreciating asset, not unlike a new car, but BC, like diamonds, is forever."-German A. Salazar
Excelent, thank you. I just want a single shot .338RUM and was going to start with a stevens 200 in .300 Win Mag.Long and short. It's a lot of work to get them to work as a repeater and they work great as a single shot. So, any action with a magnum bolt head will work.
That will work nicely.
Vietnam Vet, Jun 66 - Dec 67
My McGowan barrel using 300grn Bergers are touching the lands @ 4.030 consistantly!
Bergers in all of my other guns usually shoot best on the lands or jammed .010.
I havn't found anybody using Bergers and listing their OAL.
Has anyone tried or heard of anyone shooting a 338 Edge using Berger 300grns on the lands or jammed?
[B][SIZE=3]Dennis[/SIZE][/B]
Are the Bergers in your other guns VLD's?
Remember, the Berger 338 isn't a VLD, it's a hybrid. They shouldn't be jump/jam sensitive like the VLD's.
"Muzzle velocity is a depreciating asset, not unlike a new car, but BC, like diamonds, is forever."-German A. Salazar
Yes, all of my others are VLD'sAre the Bergers in your other guns VLD's?
What is the difference between VLD's and Hybirds?
Otherwise, all info I have found on the 338 Edge loads state their COAL is around .050 off the lands, again your thoughts?
[B][SIZE=3]Dennis[/SIZE][/B]
Most simply.
The secant ogive is the long sleek taper that VLD's are known for. They leave a shorter bearing surface and use the lands to help get the bullet started and aligned as it starts to travel down the barrel.
The tangent ogive is a little more abrupt, like on Accubonds, SMK's and the like. They leave a longer bearing surface and don't need the lands for alignment.
The hybrid uses a tangent next to the where the lands engage the bullet and then a secant to the bullet tip. This gives a good compromise between stability and higher BC form factor.
I use the 300g SMK seated about .250" away from the lands.
"Muzzle velocity is a depreciating asset, not unlike a new car, but BC, like diamonds, is forever."-German A. Salazar
I am going to load up a few starting .030 out and move in using the same H1000 load! Will keep everbody posted. In fact, all my SMk's loads are good on the lands. I just don't wont to over pressure thegun.
[B][SIZE=3]Dennis[/SIZE][/B]
geargrinder, it also helps that your barrel was dialed into .0002" to the bore when the chamber was cut haha
I use the 300g SMK seated about .250" away from the lands.
Impressive!it also helps that your barrel was dialed into .0002" to the bore when the chamber was cut
[B][SIZE=3]Dennis[/SIZE][/B]
Unless I am working on a blank that I can not get lined up that good (cheapy blanks) all of my barrels are dialed into that spec. The little extra goes a long way especially when you are shooting 1000+ yrds
No doubt.
It also helps that the bearing surface on the SMK is so long that even after the .250" jump, there is still more than .250" bearing surface in the neck.
I think that's the reason that SMK's and Berger Hybrid's just aren't sensitive to jump/jam. I don't recall hearing about anyone with an Edge that doesn't shoot.
"Muzzle velocity is a depreciating asset, not unlike a new car, but BC, like diamonds, is forever."-German A. Salazar
Posting Permissions
Bookmarks