So....really no discernible difference.
I thought I should share this. This is a model 12 LRPV in .233 caliber with a factory precision stock that has been bedded.
These are 3 shot groups at 100 yards with 80 gr Nosler CC.
The top row is all three bolts to the same torque in inch pounds from 10-60 left to right.
The middle row is the front two bolts torqued to 30 and the back bolt started at 5 going up to 40 inch pounds on the bottom row left. On the far bottom right is a group with 60-5-60
So....really no discernible difference.
Eh. You only had 100yds listed. Should post the 300yd groups as well.
30-30-5 looks good.
Never got caught up in torque screw tuning. Yes you can change group
sizes by (pardon my pun) screwing around but, tighten it donwn and get
on with some real load development. Don't let the action become a variable.
If anything, go to the other end and add a tuner. You have a few nice groups
showing that probably only needs a slight charge change, neck tension change,
or seating change.....Just my experience on the 3 PTA's I shoot and two of
them in competition both short course and long. When I mount up it's 50/45/35
and other then recheck torque after settling in, the screws no longer come into
play.
Keeping my bad Karma intact since 1952
I assumed that what he did, that’s what I did.
I wont argue with that group. I go to a deer match once a month that's shot at 400.
that group would earn you some prize money against some of the custom guns. If your
rifle is factory, you could win every month.....I see the bullet and powder, but where is
your seating at ?? Are you anywhere near the lands, or have a good jump ??
Keeping my bad Karma intact since 1952
Seating depth is bit of a sore thumb. When I received this gun back in May it came with the wrong twist. It was supposed to have a 1:7 twist but had a 1:12 twist. I just got it back from Savage last month and it has the correct twist but the throat is still fairly short. Jammed ogive is 1.926 with OAL of 2.482. That group was shot with an ogive of 1.858 and OAL of 2.411. I need a little more throat so IÂ’ve ordered a uni reamer from Pacific Tool. Ultimately I would like to have my ogive at the 1.926 at touch.
I know I shouldnÂ’t mess with it but I want to be able to shoot 90 gr bullets and right now I canÂ’t.
That is among the BEST 223 groups at 400yds I’ve ever seen, REGARDLESS of the rifle. And as Fuj said, being stock makes it even MORE impressive! One of kind, or diamond in the rough even! I wouldn’t even worry about shooting 90gr.
In any case, the PTG Uni-Throater works well. I recently used one on my Shilen barrel. I actually rented it from 4D reamer rentals. Great experience, & I’ll use them again. Think it was like $48 shipped to me. And like $12 to ship it back. If you are only planning to use it once, might want to check it out. https://4drentals.com/product/6mm-precision-throater/
You do seem to have your numbers down, and where you want to go.
As Dave mentioned, you can throat it yourself if you feel capable, or just
spin off the barrel an have a local smith do it. The way it's shooting it
looks like it has a tight throat. I like to test ream into a different piece
of stock then do a casting to check numbers.
Keeping my bad Karma intact since 1952
It’s easy. Just take your time. Don’t try to rush it. And check after each cut. Do you have a Comparator? I’m guessing you do. If not get one.
Exactly! I made up a little phrase I would constantly say to those I was instructing in basic pistol & even more advanced. It was for always checking for empty chamber as the first point, but same thing applies. “Triple check your Double check”, I’d say. Then I would rack the slide twice while looking at the chamber, then rack it three more times. And I would repeat that to students over & over again. It’s cool when I hear my son say it now.
This actually works very well on a Savage as well as many rifles or other makes. https://www.accurateshooter.com/tech...torque-tuning/
I have used it many times at the range while helping out a fellow shooter, and recently at a match when buddy's model 10 starting throwing shots. He was able to finish very well after tuning the rear screw.
Works on two screw as well as three screw actions. I have 5 Savage rifles, both small and large shank and never try to shoot without performing this tuning step.
Banning a gun will not solve what is a mental health crisis inflamed by incendiary rhetoric on social and television media. The first amendment in this case is less precious and more likely the causal factor than the second amendment.
Bob Greenleaf (retired Savage engineer and long time benchrest shooter) did similar testing back in the day when Savage first came up with the 3-screw idea. Long story short is he found the middle screw did nothing to improve accuracy, and in fact tended to make the gun more fickle when it came to screw torque. He provided his detailed results to Savage, but they opted to stick with the idea as it was something they could brag about in their marketing even if it offered no benefit. Bob's advice was just to ditch the middle screw and call it good.
"Life' is tough. It's even tougher if you're stupid." ~ John Wayne
“Under certain circumstances, urgent circumstances, desperate circumstances, profanity provides a relief denied even to prayer.” —Mark Twain
That's funny you mentioned that because that was going to be my next test But that is going to have to wait until after my throat reamer arrives. I received some 90 gr. SMK the other day and it looks like I'm going to have to ream out .064 to be able to have an OAL of 2.555 and an ogive of1.970. I'm curious to see if the 80 gr. SMK will still preform with that much jump.
I figured that without even being an 11-TEENTH degree Gun Engimi-neer. It just seems counter productive. And I really do like removable magazines. Even in my Bolt guns.
Bookmarks