Page 1 of 2 12 LastLast
Results 1 to 25 of 37

Thread: Problems cutting, threading, and recrowning a barrel.

  1. #1
    Basic Member
    Join Date
    Jan 2016
    Location
    Indiana
    Age
    45
    Posts
    68

    Problems cutting, threading, and recrowning a barrel.


    A barrel crown and lands at the end of the barrel really do matter. I cut a 308 barrel down to 18 1/4” and used an annular cutting jig to rethread the barrel. After I finished crowning, I took the rifle out and shot it. Cold bore shots were dead on, but as I continued shooting the bullets would drift left.
    After messing with different bullet weights and powder charges I finally discovered that I had messed up the lands at the end of the barrel because I used the bore guide wrong on the annular cutter.
    I swapped barrels to a barrel I know is good and I’m back to consistent groups.


    Sent from my iPhone using Tapatalk

  2. #2
    New Member
    Join Date
    Oct 2007
    Location
    Philadelphia Pa
    Age
    78
    Posts
    1,185
    Unless you are an owner of a gun lathe and know how to use it let a good gun smith do it for you

  3. #3
    Basic Member
    Join Date
    Oct 2011
    Posts
    443
    You're conflating different operations.
    A piloted annular cutter, followed by a similarly piloted threading die can deliver "acceptable" results for such things as slant brakes on AK's where it's not possible to remove the barrel nor a traditional lathe operation (been there, done that). I'd never use one where very tight tolerances are needed.

    Crowning is different tooling. You need an 11 degree, or flat piloted reamer. What did you use?

    The problem with annular cutter pilots is two-fold, they're solid- and don't come in half-thou sizes at minimum to get a precise fit in the bore; one that's too tight will score/damage the lands, too loose will result in chatter, threads that aren't concentric to the bore.

    Crowning "by hand" can be done with the correct tooling, Manson offers a couple of kits that will do this.

  4. #4
    Banned
    Join Date
    Jan 2015
    Posts
    539
    educations cost money, how much did this cost, and what did you learn ?
    crown angle can be anything. most of my rifles a FLAT.

  5. #5
    Basic Member big honkin jeep's Avatar
    Join Date
    Mar 2007
    Location
    Metro Atlanta Georgia.
    Posts
    2,546
    I've cut and crowned with a hacksaw, a file and a round headed brass screw with lapping compound chucked up in a drill, I've also crowned with a Lee case length gauge and cutter. Never any problem with the results.
    A good wife and a steady job has ruined many a great hunter.

  6. #6
    Banned
    Join Date
    Jan 2015
    Posts
    539
    i guess all lathe makers and gunsmith should quit.....
    or
    we don't all have the same quality standards.

    Quote Originally Posted by big honkin jeep View Post
    I've cut and crowned with a hacksaw, a file and a round headed brass screw with lapping compound chucked up in a drill, I've also crowned with a Lee case length gauge and cutter. Never any problem with the results.

  7. #7
    Basic Member
    Join Date
    Dec 2006
    Posts
    3,356
    I was told by a very prominent gunsmith years ago that you never use a piloted cutter on a crown.
    "As long as there's lead in the air....there's still hope.."

  8. #8
    Basic Member
    Join Date
    Oct 2011
    Posts
    443
    Quote Originally Posted by sharpshooter View Post
    I was told by a very prominent gunsmith years ago that you never use a piloted cutter on a crown.
    Uh huh....

    To each their own.
    Perhaps he could explain to you why it's fine to use piloted reamers to cut a chamber, but not a piloted cutter to do a crown?

    Both PTG and Manson manufacture piloted HSS, 11-degree cutters for a reason. Much faster than re-setting my compound to 11 degrees and cutting with a turning tool.

  9. #9
    Banned
    Join Date
    Jan 2015
    Posts
    539
    most precision rifle makers DO NOT USE PILOTS on reamers.
    the bore is taper bored to match the reamer.
    all done where the throat is dialed in.
    piloted reamers for the masses...NOT FOR PRECISION WORK.
    its been probably 15 years or more since i used a pilot to cut a chamber.
    this is a savage forum, so yes it probably works at this level.

    Quote Originally Posted by tobnpr View Post
    Uh huh....

    To each their own.
    Perhaps he could explain to you why it's fine to use piloted reamers to cut a chamber, but not a piloted cutter to do a crown?

    Both PTG and Manson manufacture piloted HSS, 11-degree cutters for a reason. Much faster than re-setting my compound to 11 degrees and cutting with a turning tool.

  10. #10
    Basic Member
    Join Date
    Jan 2016
    Location
    Indiana
    Age
    45
    Posts
    68
    Thanks for feedback. I have a lathe and am comfortable with the normal methods. And I’ve also used a hacksaw and file before as well. I had never tried an annular cutter, so I gave it a shot. As tobnpr stated, the pilots were too tight and didn’t float as freely as needed. My plan for the barrel is to put it on my lathe and cut it back past the damaged lands. Lesson learned.
    I learn by experimenting, which is why I have savage rifles - they are easy to experiment with. What I really enjoy doing is finding ways for average people to take cheap rifles, perform garage shop work, and make them shoot very accurately. I have more time than money, and I continue to learn along the way.
    I really appreciate everyone’s feedback.

  11. #11
    Basic Member
    Join Date
    Oct 2011
    Posts
    443
    Quote Originally Posted by mikeinco View Post
    most precision rifle makers DO NOT USE PILOTS on reamers.
    the bore is taper bored to match the reamer.
    all done where the throat is dialed in.
    piloted reamers for the masses...NOT FOR PRECISION WORK.
    its been probably 15 years or more since i used a pilot to cut a chamber.
    this is a savage forum, so yes it probably works at this level.

    Sure thing, boss.
    I'm in absolute awe of your expertise.
    Now, you can go brag to someone who gives a sh**.

    I pre-bore, and use a flush system.
    I still prefer a snug-fitting pilot to eliminate chatter.
    Despite your opinion, MOST professionals still use piloted reamers unless they're chambering with a specific CNC setup.

    I mean, jeez...
    What HACKS they are at McMillan Rifles... I'm sure you've got it all over those guys, they have no clue what they're doing.
    Can you BELIEVE they're chambering barrels between centers, with a PILOTED reamer- you'd better call 'em up and tell them the RIGHT way to do it!

    https://www.youtube.com/watch?v=Adsz...&index=35&t=3s

    You're nothing but a effing blowhard shi*head.

  12. #12
    Basic Member hamiltonkiler's Avatar
    Join Date
    Oct 2018
    Location
    Central NC
    Age
    37
    Posts
    456
    Quote Originally Posted by tobnpr View Post
    Sure thing, boss.
    I'm in absolute awe of your expertise.
    Now, you can go brag to someone who gives a sh**.

    I pre-bore, and use a flush system.
    I still prefer a snug-fitting pilot to eliminate chatter.
    Despite your opinion, MOST professionals still use piloted reamers unless they're chambering with a specific CNC setup.

    I mean, jeez...
    What HACKS they are at McMillan Rifles... I'm sure you've got it all over those guys, they have no clue what they're doing.
    Can you BELIEVE they're chambering barrels between centers, with a PILOTED reamer- you'd better call 'em up and tell them the RIGHT way to do it!

    https://www.youtube.com/watch?v=Adsz...&index=35&t=3s

    You're nothing but a effing blowhard shi*head.
    I ignore him


    Sent from my iPhone using Tapatalk

  13. #13
    Banned
    Join Date
    Jan 2015
    Posts
    539
    i have no chatter with no pilot...
    maybe you are doing something wrong,
    i did not say ALL gunsmiths, I DID SAY PRECISION RIFLE MAKERS.
    not all gunsmiths fall into the precision catagory
    i am a national champion with a rifle i built myself WITHOUT A PILOT.


    Quote Originally Posted by tobnpr View Post
    Sure thing, boss.
    I'm in absolute awe of your expertise.
    Now, you can go brag to someone who gives a sh**.

    I pre-bore, and use a flush system.
    I still prefer a snug-fitting pilot to eliminate chatter.
    Despite your opinion, MOST professionals still use piloted reamers unless they're chambering with a specific CNC setup.

    I mean, jeez...
    What HACKS they are at McMillan Rifles... I'm sure you've got it all over those guys, they have no clue what they're doing.
    Can you BELIEVE they're chambering barrels between centers, with a PILOTED reamer- you'd better call 'em up and tell them the RIGHT way to do it!

    https://www.youtube.com/watch?v=Adsz...&index=35&t=3s

    You're nothing but a effing blowhard shi*head.

  14. #14
    Banned
    Join Date
    Jan 2015
    Posts
    539
    i know you have an issue with big words so i'll spell it out for you
    precision rifles are a step above tactical and hunting rifles.
    competition rifles that shoot at small targets not large steel plates.
    read mc m own ad:
    "McMillan Firearms is a 32-year-old manufacturer of hunting and tactical bolt-action rifles."
    your version of precision and mine are very different, and i don't have to call you names to get my point across.


    Quote Originally Posted by tobnpr View Post
    .

    I mean, jeez...
    What HACKS they are at McMillan Rifles... I'm sure you've got it all over those guys, they have no clue what they're doing.
    Can you BELIEVE they're chambering barrels between centers, with a PILOTED reamer- you'd better call 'em up and tell them the RIGHT way to do it!

    https://www.youtube.com/watch?v=Adsz...&index=35&t=3s

    You're nothing but a effing blowhard shi*head.

  15. #15
    Team Savage GaCop's Avatar
    Join Date
    Mar 2007
    Location
    Warner Robins, Ga
    Age
    77
    Posts
    4,983
    Quote Originally Posted by mikeinco View Post
    i know you have an issue with big words so i'll spell it out for you
    precision rifles are a step above tactical and hunting rifles.
    competition rifles that shoot at small targets not large steel plates.
    read mc m own ad:
    "McMillan Firearms is a 32-year-old manufacturer of hunting and tactical bolt-action rifles."
    your version of precision and mine are very different, and i don't have to call you names to get my point across.
    It's the superior way you come across to people that elicits that type of reaction. It should tell you something but, it doesn't.
    Vietnam Vet, Jun 66 - Dec 67

  16. #16
    Basic Member Fuj''s Avatar
    Join Date
    Dec 2019
    Location
    Erie, Pa. U.S.A.
    Age
    71
    Posts
    789
    Quote Originally Posted by tobnpr View Post
    Sure thing, boss.
    I'm in absolute awe of your expertise.
    Now, you can go brag to someone who gives a sh**.

    I pre-bore, and use a flush system.
    I still prefer a snug-fitting pilot to eliminate chatter.
    Despite your opinion, MOST professionals still use piloted reamers unless they're chambering with a specific CNC setup.

    I mean, jeez...
    What HACKS they are at McMillan Rifles... I'm sure you've got it all over those guys, they have no clue what they're doing.
    Can you BELIEVE they're chambering barrels between centers, with a PILOTED reamer- you'd better call 'em up and tell them the RIGHT way to do it!

    https://www.youtube.com/watch?v=Adsz...&index=35&t=3s

    You're nothing but a effing blowhard shi*head.
    Tell em' how you really feel !!
    Keeping my bad Karma intact since 1952

  17. #17
    Basic Member Fuj''s Avatar
    Join Date
    Dec 2019
    Location
    Erie, Pa. U.S.A.
    Age
    71
    Posts
    789
    Quote Originally Posted by mikeinco View Post
    this is a savage forum, so yes it probably works at this level.
    Maybe an apology would be in order. Or better yet.....Take a hike and let
    the door hit you in the azz.
    Keeping my bad Karma intact since 1952

  18. #18
    Banned
    Join Date
    Jan 2015
    Posts
    539
    just because this is a savage site , does not mean the world revolves around it. closing your eyes to facts does not change them.


    Quote Originally Posted by Fuj' View Post
    Maybe an apology would be in order. Or better yet.....Take a hike and let
    the door hit you in the azz.

  19. #19
    Basic Member
    Join Date
    Sep 2019
    Location
    Virginia
    Posts
    384
    I had a factory 308 barrel that was tight 3” back from the muzzle, I used the “big honkin Jeep” method to go back to clean lands, and it came out just fine.

  20. #20
    Basic Member
    Join Date
    Jan 2015
    Posts
    503
    Quote Originally Posted by mikeinco View Post
    i have no chatter with no pilot...
    maybe you are doing something wrong,
    i did not say ALL gunsmiths, I DID SAY PRECISION RIFLE MAKERS.
    not all gunsmiths fall into the precision catagory
    i am a national champion with a rifle i built myself WITHOUT A PILOT.
    That’s cool. What did you build the action and barrel out of?

  21. #21
    Banned
    Join Date
    Jan 2015
    Posts
    539
    from a truck axle and a chevy block.
    pretty poor question..
    i said i BUILT the rifle,
    i did NOT say i MANUFACTURED the parts.

    Quote Originally Posted by gbflyer View Post
    That’s cool. What did you build the action and barrel out of?

  22. #22
    Basic Member
    Join Date
    Dec 2006
    Location
    Waukesha County, WI
    Posts
    368
    Man, I haven't seen this level of back and forth here for a long time :)

  23. #23
    Basic Member
    Join Date
    Jan 2015
    Posts
    503
    Quote Originally Posted by mikeinco View Post
    from a truck axle and a chevy block.
    pretty poor question..
    i said i BUILT the rifle,
    i did NOT say i MANUFACTURED the parts.
    Hahahaha. Good one. I thought maybe you were one of those folks who has the stuff to do it all. Thanks for setting me straight

  24. #24
    Basic Member
    Join Date
    Jul 2012
    Location
    Northern MN
    Age
    72
    Posts
    673
    Quote Originally Posted by mikeinco View Post
    just because this is a savage site , does not mean the world revolves around it. closing your eyes to facts does not change them.
    Don't confuse "facts" with opinions. Seems your opinions are not supported by actual facts or science.

  25. #25
    Banned
    Join Date
    Jan 2015
    Posts
    539
    lets see you prove me wrong
    precision rifles not hunting tactical rifles

    Quote Originally Posted by mnbogboy2 View Post
    Don't confuse "facts" with opinions. Seems your opinions are not supported by actual facts or science.

Page 1 of 2 12 LastLast

Similar Threads

  1. Cutting your own barrel down...
    By celltech in forum 110-Series Rifles
    Replies: 11
    Last Post: 01-14-2018, 09:58 PM
  2. cutting the barrel on my 12FV
    By waumpuscat in forum 110-Series Rifles
    Replies: 6
    Last Post: 04-07-2016, 07:05 PM
  3. Replies: 5
    Last Post: 12-07-2011, 11:32 AM
  4. cutting a fluted barrel
    By bigbada in forum 110-Series Rifles
    Replies: 18
    Last Post: 10-10-2010, 11:40 PM
  5. Replies: 7
    Last Post: 09-24-2010, 05:33 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •