The top action is a Savage target action. The bottom action is a Savage model 12 F-T/R action. Both have target triggers and have large shanks. What's the difference between them other than mounting bolt spacing? And, if that's the only difference, why would Savage do that?
Dave
You DO know you can drill and tap the holes in different positions? Just make sure the action screws don't get in the way of the bolt head or body.
Oz never gave nothing to the Tin Man, that he didn't already have.
Yes, I did figure that part out. I just need to find a LGS who won't charge me more than what I paid for the action.Originally Posted by Nor Cal Mikie
Is one a LA and the other a SA ?
The one on the bottom allows for a longer front screw
The Dunning-Kruger effect is alive and well.
I'm not so sure about that. It still needs to allow the bolt head to pass by.
Longer screw cut to fit with no bolt contact.
Oz never gave nothing to the Tin Man, that he didn't already have.
No difference what-so-ever other than the screw spacing. As to why Savage would do that, that's the $10,000,000 question many of us have been asking since Savage came out with them in 2008.
"Life' is tough. It's even tougher if you're stupid." ~ John Wayne
“Under certain circumstances, urgent circumstances, desperate circumstances, profanity provides a relief denied even to prayer.” —Mark Twain
It's a non-issue, as the screw goes up thru the lug abutment, not just the thin part of the receiver wall. It'd have to be one *long* damn screw to reach the bolt in that location - if it's even a thru hole; don't have one in front of me ATM.
Sent from my SM-G960U using Tapatalk
The bolt head is not in battery when passing by the screw that is farther back.
Oops the above post says the same thing only better.
Sorry
I emailed Savage asking what they would charge to redrill and tap my receiver. Here's the reply:
Hi Dave,
No, we do not offer that service.
thank you,
Debbi
Sometimes, Savage just blows me away!
Both are SA.
It's simple.....the reason Savage changed the hole spacing was to gain more thread engagement on the front screw, and to eliminate the notch in the rear pillar. If you notice the rear hole (untapped) is still in the same place. That is because that's what is used as a reference for all other machining operations. The "new" rear hole was strategically placed to use the model 40 trigger guard. When this was first implemented, the plan was to eventually change all of the single shot target actions to this spacing, once the supply of the 4.4 stocks were exhausted. Then a brainiac engineer decided to come up with a repeater version of the LRPV, and that threw a monkey wrench in the gears. The original models that were to utilize this new spacing were the Model 12 Dual port Benchrest rifle, and the Model 12 Palma rifle, all others used the 4.4 spacing.
Over the last several years, the 3.44 spacing has shown up on models and target actions that were never intended to be that way, and vice versa on the 4.4, because of mix ups in the machining operations and misplaced macro's (sub programs) that resulted in bastardized receivers. To remedy the problem on finished rifles, an appropriate stock was used. For Precision Target actions, the correct trigger guard was included (most of the time) and the problem was left to the gun builder. This only created a lot of confusion when the stock was ordered, and that's why it is so important to measure the hole spacing, and not assume. This was especially problematic when someone would order a stock before they received their action and actually measured it. The easiest way to correct that dilemma is to re-drill and tap the receiver, it's lots easier than trying to move pillars. It doesn't hurt anything, but Savage does not condone this practice since they have no control over it.
One observation I have is that the shorter screw spacing seems to be more bedding sensitive than the longer one. Every 6BR Dual port that I have played with benefited greatly from a bedding job. To prove a point, I re-drilled one and shot it using 2 bench rest stocks that had the 2 different screw spacing's. Both stocks had pillars but were not bedded. The difference in groups were night and day, with the 4.4 spacing having the advantage. I then bedded in the 3.44 stock with Devcon and brought the accuracy up the same level as the 4.4 stock. It's evident to me that the 4.4 screw spacing is less finicky and has an advantage over the shorter 3.44 set-up .
"As long as there's lead in the air....there's still hope.."
Posting Permissions
The sole purpose of this site is to provide an online community for those who wish to interact with other Savage firearm enthusiasts.
The information and opinions expressed within this site are those of its contributors, and in no way should be viewed as the opinions or recommendations of Savage Arms.
This site utilizes affiliate programs to generate revenue and as such purchasing a product reached by clicking on a link on this site may earn us a small commission on that sale.
Reply With Quote
Bookmarks