Page 1 of 2 12 LastLast
Results 1 to 25 of 38

Thread: Trying the Oryx chassis on the 12 FV 6.5mm Creedmoor

  1. #1
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802

    Trying the Oryx chassis on the 12 FV 6.5mm Creedmoor


    I bought an Oryx chassis for the 12 FV .223 so I could eliminate the hidden magazine that made loading a chore. But the Oryx chassis allows a Savage short action to drop right into the frame without any further adjustments, so I figured that I would pull the Oryx chassis off my 12 FV .223 and try in on the 12 FV 6.5mm Creedmoor.

    The 12 FV 6.5mm Creedmoor has a NightForce 8-32X56mm Benchrest scope with a 30mm tube mounted on it and the large front objective required high rings to let the front objective clear the barrel. I figured it was worth a test to see if that configuration would work with the no-drop Oryx chassis. I had to lower the cheek rest on the Oryx chssis to the minimum setting to be comfortable getting my eye on the optical plane.

    I loaded 4 different bullets, all with loads that worked well with the factory stock and figured that a comparison of the results would allow me to decide:

    1. Whether the Oryx stock would eliminate the stock flexing I was feeling with the factory plastic stock.
    2. Provide a comfortable platform that allows a consistent set up.
    3. Improves the accuracy over the factory plastic stock.


    The following are the results shot in Northern Virginia on Monday afternoon, July 8th at 100 yards. Temperatures were from 74 to 76 degrees with winds from 5 to 8 mph with moderate to heavy rain for most of the afternoon. Altitude of the range is 250 feet above sea level.

    I was serving as range safety officer for the afternoon and normally I would not shoot when there were any shooters on the range, but the weather was rainy and everyone stayed away. With the range all to myself, I got out the 12 FV 6.5mm Creedmoor and shot 100 rounds with the Oryx chassis with 4 different loads using 4 different bullets.

    All rounds were shot using Lapua brass and CCI BR-4 primers.

    All loads were set up to match the 12th reflection time of 1.360 msec. for the 26-inch barrel with a 0.040 recessed crown. The action screws were torqued to 60 in.-lbs. per the Oryx directions prior to this session.

    The load description field shows the powder and charge, the O.A.L., the trim length, and the bullet exit time from the 26-inch barrel.

    # Grps Load Description Bullet Weight Velocity Average Median St Dev 1 2 3 4
    4 IMR4451 38.9 gr 2.845 1.903 wf 1.360 * 79/74 deg. F. 60 in.-lbs. Oryx CCI BR-4 Sierra TMK #7430 130 2701 0.331 0.345 0.031 0.244 0.343 0.346 0.350
    4 IMR44451 38.8 gr 2.823 1.909 wf 1.360 * 75/76 deg. F. 60 in.-lbs. Oryx CCI BR-4 Hornady ELD-M #26331 140 2666 0.337 0.334 0.052 0.284 0.301 0.357 0.394
    4 IMR4451 39.0 gr 2.835 1.912 wf 1.359 * 72/74 deg. F. 60 in.-lbs. Oryx CCI BR-4 Sierra SMK #1742 142 2665 0.339 0.359 0.061 0.254 0.337 0.380 0.386
    4 IMR4451 38.8 gr 2.358 1.906 wf 1.359 * 77/75 deg. F. 60 in.-lbs. Oryx CCI BR-4 Hornady ELD-X #2635 143 2658 0.335 0.327 .038 0.297 0.324 0.329 0.388
    16 0.335 0.340 0.042











    Comparison of Factory Stock with Oryx Chassis
    Factory Oryx Chassis
    Bullets Weight Avg. Median St Dev # Grps. Avg. Median St Dev # Grps.
    Sierra TMK #7430 130 0.357 0.352 0.056 31 0.331 0.345 0.031 4
    Hornady Match # 26331 140 0.373 0.355 0.081 35 0.337 0.334 0.052 4
    Sierra SMK #1742 142 0.304 0.306 0.045 11 0.339 0.359 0.061 4
    Hornady ELD-X #2635 143 0.375
    0.369
    0.069
    39
    0.335
    0.327
    0.038
    4
    0.363 0.345 0.062 116 0.335 0.340 0.042 16

    The average of the results with the Oryx stock shows a 7.6% improvement over the factory stock with the same bullets.

    However, I have a tendency to take a session or two to get accustomed to a new configuration before I get the most out of it, so I think it may take more than one session to see the benefits of the Oryx chassis.

    The Oryx chassis did eliminate all the flexing that occurred with the factory plastic stock and the platform was incredibly stable through recoil. I could hear the chassis twang a bit, almost like the sound of an AR recoil spring after the initial bang.
    The removal of the flexing of the factory stock was the primary reason for trying the Oryx on the 6.5mm Creedmoor.
    Last edited by CFJunkie; 07-09-2019 at 08:12 PM. Reason: Spacing

  2. #2
    Basic Member
    Join Date
    Apr 2019
    Location
    missouri
    Age
    74
    Posts
    79
    Had a ?,what magazine are you using in your ORYX chassis, ? . i have 2 of the plastic 6 creedmoor 102232's, rounds set too low to feed, if you load 1 at a time no problem. Don't have a 6.5 creedmoor,do have a 6.5/284,the 120,123 grain A-max and the 120,123,and 130 ELD's shoot in the low .2's to the low .3's

  3. #3
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    I bought one 10 round mag from MDT but found out, after it arrived, that the plastic follower and the molded top restricted the O.A.L. to about 2.830. I get the best results when I seat my Hornady and Sierra Bullets out past that.
    I ordered an all-metal 5-round AI mag from Brownell's that has about 2.895 available length for O.A.L. and that was what I used for the loads I shot ( 2.858, 2.845 and 2.835 wouldn't fit in the MDT magazine).
    It feeds great and drops right out of the mag well when you press the release. The MDT mag doesn't do that.

  4. #4
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    This are the latest results of the second session using the Oryx chassis with the Savage 12 FV 6.5mm Creedmoor action on July 16th with an 8-32X56mm NightForce scope with a 30-mm tube mounted with Burris ZEE Signature high rings. The session was shot in Northern VA at 100 yards at an altitude of 250 feet above sea level. The temperatures were quite a bit hotter than forecasted so I was fortunate to be using a powder that is temperature insensitive. The net effect a temperature variation of 10 degrees on velocity was only about 1 fps.

    All the loads were shot using Lapua brass.
    All bullets were loaded to achieve a 1.359 to 1.360 msec. exit time (12th reflection) to stay under Pmax using IMR4451 powder. The jump for each load was approximately 0.020 with adjustments within 0.003 made to achieve the desired exit time.

    The primers were switched to use CCI BR-4 primers with the first loads of the Sierra 142 gr SMK #1742 bullets and 140 grain Hornady ELD-M #26331 bullets. Remington 7 ½ primers were loaded for the second loads of the Sierra 142 gr SMK #1742 bullets and the Hornady 140 gr #26331 ELD-M # 26331 bullets with approximately the same loads for both sets, adjusted only for differing brass trim lengths. I planned to compare the results for the CCI BR-4 primers and the Remington 7 ½ from this session. I expect to try this again to get a larger statistical sample size.

    The load description field shows the powder and charge, the O.A.L., the trim length, and the bullet exit time from the 26-inch barrel.
    # Grps Load Description Bullet Weight Velocity Average Median St Dev 1 2 3 4
    4 IMR4451 39.1 gr 2.841 1.910 wf 1.359 * 72/81 deg. F. 60 in.-lbs. Oryx CCI BR-4 Sierra SMK #1742 142 2666 0.331 0.357 0.082 0.216 0.331 0.383 0.395
    4 IMR4451 39.0 gr 2.847 1.907 wf 1.359 * 74/83 deg. F. 60 in.-lbs. Oryx CCI BR-4 Hornady ELD-M #26331 140 2670 0.356 0.333 0.0.112 0.257 0.277 0.389 0.499
    4 IMR4451 39.1 gr 2.838 1.905 wf 1.359 * 76/86 deg. F. 60 in.-lbs. Oryx Rem 7 ½ Sierra SMK #1742 142 2666 0.363 0.367 0.014 0.343 0..365 0.368 0..376
    4 IMR4451 39.1 gr 2.854 1.901 wf 1.359 * 78/87 deg. F. 60 in.-lbs. Oryx Rem 7 ½ Hornady ELD-M #26331 140 2672 0.355 0.344 0.048 0.311 0.327 0.360 0.420
    16 0.351 0.363 0.067

    To get a comparison of the factory stock versus the Oryx chassis performance, I went back to my records and compared previous results with these two bullets shot with the same powder and scope using the plastic factory stock and the Oryx chassis.

    The overall average group size for the first session using the Oryx chassis with the 12 FV action, the NightForce scope and IMR4451 powder and 4 different bullets averaged 0.335 for 16 groups.

    During previous sessions using the plastic factory stock using IMR4451 powder and NightForce scope, the 140 gr Hornady ELD-M bullets averaged 0.349 for 18 groups. During the previous session with the Oryx chassis, the 140 gr Hornady ELD-M bullets averaged 0.337 for 4 groups using CCI BR-4 primers, IMR4451 powder and the NightForce scope. During today’s session, the same bullets using the Oryx chassis averaged 0.355 for 8 groups with IMR4451 powder with the NightForce scope giving the Oryx chassis an average to date of 0.349 - identical to the factory stock.

    During previous sessions using the plastic factory stock using IMR4451 powder with the NightForce scope, the 142 gr SMK bullets averaged 0.352 for 9 groups. During previous sessions using the Oryx chassis with the 12 FV action, the 142 gr Sierra SMK bullets averaged 0.339 for 4 groups using CCI BR-4 primers and IMR4451 powder with the NightForce scope. During today’s session, the same bullets and the Oryx chassis averaged 0.347 for 8 groups with the same powder and scope giving the Oryx chassis an average to date of 0.345 – slightly better than the factory stock.

    There were only 4 groups for each of the two bullet loads with the two types of primers. The CCI BR-4 primers averaged 0.343 for 8 groups and the Remington 7 ½ BR primers averaged 0.359 for 8 groups. Unfortunately, the sample size is too small to make any final conclusions but the BR-4 primers performed slightly better so far. That is the opposite of the preliminary performance of these two primers to date on the 12 FV .223 with 77 grain SMK and TMK bullets.
    Last edited by CFJunkie; 07-16-2019 at 05:13 PM. Reason: Spacing

  5. #5
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    Here is the Flat Dark Earth version of the Oryx chassis that I bought for the 12 FV 6.5mm Creedmoor.
    I like the look of this version more than the green version I have on the 12 FV .223.

    Click image for larger version. 

Name:	Savage 12 FV 6.5mm Creedmoor Oryx FDE Chassis - right.jpg 
Views:	130 
Size:	217.0 KB 
ID:	6214
    The high rings on the NightForce 30-mm tube are just high enough to get a comfortable cheek weld with the adjustable cheek rest set at its lowest setting.

    Click image for larger version. 

Name:	Savage 12 FV 6.5mm Creedmoor Oryx FDE Chassis - left .jpg 
Views:	101 
Size:	170.3 KB 
ID:	6215
    I bought the sling swivel from Oryx to mount the Sinclair F-class bipod on the 12 FV .223 chassis, but I bought a cheaper swivel for the 12 FV 6.5mm Creedmoor from Brownell's and it
    worked just as well.

  6. #6
    Basic Member DesertDug's Avatar
    Join Date
    Jun 2018
    Location
    Texas
    Posts
    432
    Looks as good as you shoot them.

  7. #7
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    Hopefully, the results improve with this stock as much as the group sizes improved on the 12 FV .223 with the other Oryx stock.
    It took me a couple of sessions with the new set up until suddenly the groups got smaller.

    I expected quicker improvements with the 6.5mm Creedmoor because the factory stock flexed so much under recoil.
    The Oryx chassis just about eliminated the flex but I can hear the chassis 'twang' under the stress.
    It reminded me of the recoil tube noises shooting an AR.
    I guess the 'sound' is from the action bolts and recoil lug are straining against the aluminum frame.

  8. #8
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    Here are the results of the latest session with the 12 FV 6.5mm Creedmoor mounted in the Oryx chassis using the 8-32x56mm NightForce Benchrest 30mm tube scope with Burris ZEE Signature high rings. The session was shot on Saturday morning, July 27th, in Northern Virginia at 100 yards at an altitude of 250 feet above sea level.

    All the loads were shot using Lapua brass. All bullets were loaded to achieve a 1.361 msec. exit time (12th reflection) to stay under Pmax using H4350 powder and CCI BR-4 primers. I finally got some H4350 powder and I wanted to see how it would shoot in this rifle.

    I have much more data using CCI BR-4 primers than Remington 7 ½ BR primers so I decided to start with the CCI BR-4 primers that have the most data to easily compare results.

    The jump for each load was approximately 0.020 with adjustments within 0.003 made to achieve the desired exit time to account for variations in trim length.

    The load description field shows the powder and charge, the O.A.L., the trim length, and the bullet exit time from the 26-inch barrel as well as temps expected and experienced, torque, stock, primer and pressure (from QuickLOAD).

    # Grps -------Load Description -------------Bullet----- Wgt. – Vel. -- Avg. – Median – St Dev –-- 1 -------- 2 -------- 3 ------ 4 ---
    4 ---- H4350 40.9 gr 2.832 1.907 -- Hornady ---- 147 – 2649 -- 0.286 – 0.282 --- 0.040 -- 0.241 -- 0.271 –0.293 – 0.337
    --------- wf 1.361 71/71 deg.F. --------- ELD_M
    --------- 60 in.-lbs. Oryx CCI BR-4 ------ #26333
    4 ----- H4350 41.5 gr 2.856 1.905 –- Sierra -------- 142 – 2685 – 0.341 – 0.329 –-- 0.027 – 0.324 – 0.325 – 0.333 – 0.381
    --------- wf 1.361 75/74 deg. F. ------- SMK
    --------- 60 in.-lbs. Oryx CCI-BR4 ------ #1742
    4 ------- H4350 41.3 gr 2.844 1.902 – Hornady ---- 140 – 2688 – 0.320 – 0.326 –-- 0.049 – 0.254 – 0.322 – 0.330 – 0.373
    --------- wf 1.361 78/77 deg. F. ------- ELD-M
    --------- 60 in.-lbs. Oryx CCI BR-4 ------ #26331 -------------------------------------------------
    ------------------------------------------------------------- Average -- 0.315 – 0.325 --– 0.043


    H4350 powder averaged based upon the performance of the 147 grain ELD-M bullets but all three bullets managed to average better than the overall average through the last session.

    Up until today, IMR4451 led the performance results with an average of 0.355, but since the H4350 results were with the Oryx chassis, it may be more meaningful to compare the IMR 4451 results shot with the Oryx chassis to the H4350 results. Although this is a small sample, there appears to be a marked difference (7.6%) in the performance of the powders favoring H4350. It looks like there will have to be more testing with H4350 powder to see if it will continue to show that improved performance.

    H4350 IMR4451
    140 ELD-M 0.286 0.346
    142 SMK 0.341 0.335
    147 ELD-M 0.320
    -------
    0.315 0.341

  9. #9
    Basic Member
    Join Date
    Jun 2018
    Location
    Georgia
    Posts
    34
    CFJunky: I enjoyed your read. Shows a lot of time and work invested. I would like to ask how you got such good groups with the 77 grain SMKs. I have two mod 10s with Boyds target/varmint stocks. They are both factory 1/9 twist and stop at 69 SMK. They won't even think about shooting 68 or 75 grain Hornady ELD ms. The 69s will shoot consistently under 1/2 moa, but heavier just drops off the cliff. They are both due for rebarrel and I'm thinking about a 1/12 and maybe a 1/7.5 to do light and heavy bullets. They just won't do it now.

  10. #10
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    LuvmyLRP,

    I should also post this answer on my 12 FV .223 thread, but I'll answer your question one here on the 12 FV 6.5mm Creedmoor thread.
    Actually, it is hard for me to believe 77 gr bullets will even stabilize in a 1:9 twist, too!
    Everything I have heard for years and years says they won't, and even Sierra says they won't, but when I tried them, I was astounded by the results.
    I never expected the 77 gr SMKs or the TMKs to group at all, and they wound out shooting better than any other bullets I have shot from 50 grains to 70 grains with this rifle.
    The 69 SMKs and 69 TMKs shoot well in the 12 FV .223, but the 77 SMKs and TMKs shoot even better.

    Since I started shooting 77 grain bullets, my overall average improved from 0.362 to 0.320.
    My average with the 77 grain SMK and TMK bullets is 0.285.
    I can't explain it, I can only report the results.

    However, I expect it has a lot to do with loading the 77 gr bullets out to 0.020 off the lands.
    The Sierra recommended seating depth for both bullets is 2.260.
    I am shooting the SMKs at 2.290 to 2.303 and the TMKs at 2.325 to 2.345 to get the best results with my chamber depth.
    The TMK tips make using O.A.L. a bit more complicated because the tip adds at least 0.050 to the O.A.L.
    I questioned Savage about how they came up with the 2.260 recommendation and asked it the limits of an AR magazine had anything to do with it.
    The response from their rep was that the AR mag limits probably had something to do with it.

    The 77 SMKs averaged 0.395 when the O.A.L. was 2.280 or less.
    The same powder and bullet averaged 0.251 when the O.A.L was between 2.296 and 2.301.
    The 77 TMKs averaged 0.275 when the O.A.L. was between 2.330 and 2.345.
    When I moved the 77 TMK O.A.L out 2.350 to 2.353, the O.A.L was 0.330.
    When I moved the O.A.L. back to 2.293, the 77 TMKs averaged 0.289.

    I think finding out where to seat them makes a difference but I honestly can't explain why they even stabilize.
    It is pretty clear to me that with this particular rifle, the position of the bullets re the lands is pretty important.

  11. #11
    Basic Member
    Join Date
    Jun 2018
    Location
    las cruces, nm
    Posts
    2,702
    I don't know why either, but the 77 SMK's shoot best in my .223 Axis HB as well (also a 1/9 twist).

  12. #12
    Basic Member hamiltonkiler's Avatar
    Join Date
    Oct 2018
    Location
    Central NC
    Age
    37
    Posts
    456
    Bullet ogive.
    Not all bullets are created equal. The US navy special forces use bullets for a reason.
    Same with hunting. Public, “can’t hunt with a match bullet.”
    Shoot a deer with a matchking. Serria. Tell me how it does compared to other .224 bullets.
    Cheers



    Sent from my iPhone using Tapatalk

  13. #13
    Basic Member
    Join Date
    Jun 2018
    Location
    las cruces, nm
    Posts
    2,702
    The "surprise" part is that Sierra prints on their 77gn MK box, 1:8 twist or faster.

    Why would I use a match bullet for hunting? And I'd never use a .224 for deer unless it was a pure survival issue.

  14. #14
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    charlie b

    The SMK and TMK are both match bullets and I wouldn't use them for hunting either, especially on deer. The match bullets have thicker jackets and don't expand like a hunting bullet.
    It is illegal in some states to shoot deer with .224 bullets of any type, match or hunting bullets.

    Sierra recommends an O.A.L. of 2.260 for both the 77 gr SMK and TMK.
    The SMK is more accurate out around 2.290 to 2.300 and the TMK is more accurate out around 2.340.

    I asked Sierra why they recommended an O.A.L. so short for such long bullets when they shoot more accurately seated out 0.040 and 0.080 further respectively.
    I asked if the limited AR magazines had anything to do with their recommendations.
    Their rep responded by saying "it might have been a consideration."

    I agree with hamiltonkiler that their higher ballistic coefficient (related to their weight, bullet length and the secant shape of the nose) has a lot to do with their unprecedented stabilization but, like charlie b, I am amazed that Sierra doesn't seem to be aware of it.
    The 77 gr Sierras have now become a mainstay of my 12 FV .223's loads.
    I will now try the same loads in my old CZ 527 Varmint bolt action that also has a 1:9 twist and see if they do as well in a 24 inch barrel.

  15. #15
    Basic Member
    Join Date
    Jun 2018
    Location
    Georgia
    Posts
    34
    CFJunky: I'm glad that it was your post that I referenced and that I am Not losing it. Something happened when I logged in. I haven't tried the 77 SMKs, but now I'm going to. 69 SMKs are my go to accuracy bullet for .223. Guess I should try fiddling with the jump a little more. I show the chamber depth for the 69SMK in my mod 10 as 2.0380 with a Hornady 2-22 insert and I usually load it .020 off the lands. I don't know what the oal is. If it won't load in the mag, I check it. My 12 LRP 6.5CM eats about any OAL you want in the mag with room to spare. On the other, my RPR 6.5CM is limited by the mag to very short OAL. That's with a Magpul mag, but may be different with a metal mag. It's hard to single load the RPR because of the bolt hold open on the last shot. You have to really shove it hard to single load. Maybe I can find a ramp insert. With the chamber and mag combo on the RPR, it's hard to work too much on jumps. I'll say it again, LUVMYLRP. Trying to decide on which new barrel for it, but that's another thread. Thanks for the data on the .223 and 6.5. Call me crazy, but I love the LRP factory stock. I just can't get used to space gun stocks. I tried an A2 stock on my RPR, but It just didn't feel right. I would like to try the Magpul butt stock, but no one here is using one for me to try.

  16. #16
    Basic Member
    Join Date
    Jun 2018
    Location
    las cruces, nm
    Posts
    2,702
    I was in the same boat as you for a long time. Max 69gn SMK's. I read a post in here about someone who competed at 600yd with 77gn SMK's so I tried them. Since they worked I kept shooting them. I suspect that what Sierra is referring to is 20" AR barrels. The extra velocity and spin rate we can get with a 24" barrel may be the difference. I also thought it might be cause I shoot at 5000ft elevation but CFJunkie is nearer to sea level. And I get good results at 40F as well as 100F.

    FWIW, I have been loading my .223 77SMKs at the recommeded length of 2.26". Just never messed with it. As is I get consistent 0.5MOA groups out to 300yds. CFJunkie is at another level better than I am.

    I am going to try the longer length to see how much difference that makes. I have a 'control' batch loaded now so I can compare.

    Sorry for the extra off topic.

  17. #17
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    LuvmyLRP,

    I too have a LRP in 6.5mm Creedmoor and it is a dream to shoot.
    I too love the HS Precision stock. Mine came with a pretty short chamber but I have about 4,000 rounds through it and it has eroded 0.036 so I am now working to load out to maintain the jump. I bought the 12 FV in 6.5mm Creedmoor as a load development rifle for the LRP but it shot so well in the cheap plastic stock that I started a thread under Ammo and Reloading.

    When I finally shot 1,000 rounds with it, I decided to change to the Oryx stock to see if it improved its accuracy and started this thread.
    If you haven't seen the threads for the 12 FV 6.5mm CM and the 12 FV .223 on the Ammo and Reloading forum, you might want to take a look at those two also. There are lots of load data that might be useful for both your rifles, especially the 25 inch LRP in 6.5mm CM.

  18. #18
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    Here are more results with the Savage 12 FV .223 with the Oryx chassis using the 36X single power Sightron 1-inch tube scope with a target dot reticle. The action screws were torqued to 60 in.-lbs. prior to this session to match the Oryx chassis torque specs.

    This session, held in Northern Virginia at 100 yards on Friday, Aug 2nd again tested the 77 gr TMK bullets with IMR4166 powder. Temperatures on Friday, after a very rainy early morning from about 4 AM to 7 AM, were from 73 to 75 degrees from 8 AM to 10 AM with winds from calm to 3 mph. Altitude of the range is 250 feet above sea level.

    All the loads were shot using Lapua brass using Remington 7 ½ small rifle primers. All bullets were loaded to achieve a 1.361 msec. exit time (12th reflection) to stay well under Pmax using the 77 grain bullets with IMR4166 powder. The 1.361 exit time should be the sweet spot for a 26-inch 3% carbon steel barrel with a 0.040-inch recessed crown.

    For this session, I loaded IMR4166 Enduron powder and 77 grain Tipped Match King #7177 bullets with the seating depths for the 77 grain bullets to achieve the a jump to the rifling – 0.030 to 0.020 – and then adjusted the seating depth by less than 0.005 thousandths to achieve the 1.361 exit time to accommodate variations in the brass trim length. As a result, all the loads are quite similar with only slight variations in seating depth and trim length.

    The load description field shows the powder and charge, the O.A.L., the trim length, and the bullet exit time from the 26-inch barrel.

    # Grps Load Description Bullet Weight Velocity Average Median St Dev 1 2 3 4
    4 IMR4166 21.0 gr 2.343 1.749 wf 1.361 * 73/73 deg. F. Rem 7 ½ Oryx 60 in.-lbs. Sierra TMK #7177 77 2539 0.244 0.258 0.050 0.174 0.248 0.267 0.288
    4 IMR4166 21.0 gr 2.340 1.746 wf 1.361 * 73/72 deg. F. Rem 7 ½ Oryx 60 in-lbs. Sierra TMK #7177 77 2539 0.210 0.217 0.020 0.180 0.216 0.225 0.218
    4 IMR4166 21.0 gr 2.338 1.745 wf 1.361 * 75/74deg. F. Rem 7 ½ Oryx 60 in.-lbs. Sierra TMK #7177 77 2539 0.301 0.311 0.034 0.252 0.310 0.311 .0330
    4 IMR4166 21.0 gr 2.336 1.742 wf 1.361 * 77/77 deg, F. Rem 7 ½ Oryx 60 in.-lbs. Sierra TMK #7177 77 2539 0.303 .0301 0.019 0.282 0.298 0.303 0.327
    16 0.264 0.275 0.050


    Today’s session started out very well, but I changed rifles after the second load and shot a CZ 527 Varmint with a 1:9 twist and the same scope model as is on the Savage 12 FV .223 Oryx.

    I put the 12 FV aside to cool the barrel and shot a load with the CZ. Then I switched back to the 12 FV and shot the third load and switched back to the CZ again and shot another load. Finally, I switched to the 12 FV and shot the last load.

    I think the switching from the Oryx chassis to a traditional target rifle might have caused an issue getting back into position with the Oryx chassis.

    The results weren’t terrible but there was a definite difference between the first two loads and the last two loads. I find that the Oryx chassis with the pistol grip takes a bit of getting used to when you switch from a normal stock. The more traditional stock on the CZ is lighter and the trigger has a heavier pull (just over 3 lbs.) than the Savage Accu-trigger that came from the factory with a pull of 1 lb. 11 oz.

    The CZ 527 was also being tested using the same 77 TMK bullets but the CZ loads were tuned to match a 1.256 exit time for the 24-inch barrel.
    The CZ averaged 0.302 for 8 groups with the same powder and bullets. The CZ’s first load averaged 0.288 for 4 groups and the second load averaged 0.316 for 4 groups. Not bad for a rifle with over 8,000 rounds down the barrel. The groups tracked the general loss of performance for the 12 FV Oryx chassis so it might just have been the shooter losing concentration.

  19. #19
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    Whoops! I posted the .223 data on the 6.5mm Creedmoor thread.

    Sorry. Both were with Oryx chassis but that was the only similarity.

  20. #20
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    Here are additional results of the latest sessions with the 12 FV 6.5mm Creedmoor mounted in the Oryx chassis using the 8-32x56mm NightForce Benchrest 30mm tube scope with Burris ZEE Signature high rings. The difference is that these loads were using H4350 powder.

    I finally got some H4350 powder and I wanted to see how it would shoot in this rifle. The first portion of the test was shot on Saturday morning, July 27th, in Northern Virginia at 100 yards at an altitude of 250 feet above sea level. I didn’t get to finish all 4 loads.
    On August 12th I was able to shoot the last of the test at the same range at the same distance using H4350 powder and 130 grain TMK bullets.

    All the loads were shot using Lapua brass. All bullets were loaded to achieve a 1.361 msec. exit time (12th reflection) to stay under Pmax using H4350 powder and CCI BR-4 primers. I have much more data using CCI BR-4 primers than Remington 7 ½ BR primers so I decided to start with the primers that have the most data to easily compare results. The jump for each load was approximately 0.020 with adjustments within 0.003 made to achieve the desired exit time to account for variations in trim length.

    The load description field shows the powder and charge, the O.A.L., the trim length, and the bullet exit time from the 26-inch barrel as well as temps expected and experienced, torque, stock, primer and pressure (from QuickLOAD).
    # Grps -------Load Description -------------Bullet----- Wgt. – Vel. -- Avg. – Median – St Dev --- 1 -------- 2 -------- 3 ------ 4 ---
    4 ---- H4350 40.9 gr 2.832 1.907 --- Hornady ---- 140 – 2649 -- 0.286 – 0.282 --- 0.040 --- 0.241 -- 0.271 –0.293 – 0.337
    --------- wf 1.361 71/71 deg.F. --------- ELD_M
    --------- 60 in.-lbs. Oryx CCI BR-4 ------ #26331
    4 ----- H4350 41.5 gr 2.856 1.905 –- Sierra -------- 142 – 2685 – 0.341 – 0.329 –-- 0.027--- 0.324 – 0.325 – 0.333 – 0.381
    --------- wf 1.361 75/74 deg. F. ------- SMK
    --------- 60 in.-lbs. Oryx CCI-BR4 ------ #1742
    4 ------- H4350 41.3 gr 2.844 1.902 – Hornady ---- 147 – 2688 – 0.320 – 0.326 –-- 0.049 --- 0.254 – 0.322 – 0.330 – 0.373
    --------- wf 1.361 78/77 deg. F. ------- ELD-M
    --------- 60 in.-lbs. Oryx CCI BR-4 ------ #26333
    -------------------------------------------------------------- Average -------- 0.315 – 0.325 – 0.043

    This following results were from the last load shot on August 12th at the same range.

    The load description field shows the powder and charge, the O.A.L., the trim length, and the bullet exit time from the 26-inch barrel as well as temps expected and experienced, torque, stock, primer and pressure (from QuickLOAD).

    # Grps -------Load Description -------------Bullet----- Wgt. – Vel. -- Avg. – Median – St Dev ---- 1 -------- 2 -------- 3 ------ 4 ---
    4 ------ H4350 41.5 gr 2.870 1.899 --- Sierra----- 130 --- 2723 -- 0.255 – 0.247 --- 0.029 --- 0.231 -- 0.237 –0.257 – 0.296
    ----------- wf 1.361 85/85 deg. F. --------- TMK
    --------- 60 in.-lbs. Oryx CCI BR-4 ------ #7430

    The H4350 powder average was beneficially impacted by the 0.255 performance with the 130 TMK bullets and the 0.286 performance with the 140 grain ELD-M bullets and negatively impacted by the 0.341 performance of the 142 grain SMK bullets but all four loads managed to average better at 0.300 than the 0.351 overall average through the July 16th session with IMR4451 powder with the 130 TMK, 140 ELD-M, and 142 SMK bullets with the Oryx chassis. I didn’t have any more 147 ELD-M bullets at the time of the July 16th test with the Oryx chassis.
    The overall performance of all powders is shown immediately based upon bullet weight. The samples for H4350 and RL-17 are very small compared to the other powders but the overall performance of the H4350 across all the bullet weights is impressive. On the other hand, RL-17 appears to be very bullet weight sensitive. I never shot the 142 gr SMK or 147 gr ELD-M bullets with RL-17 power because the performance dropped off so significantly with the 140 grain bullets. Although the H4350 and RL-17 powders have only small sample, there appears to be a marked difference (19.1% to 34.4%) in the overall average performance of the powders favoring H4350. It looks like I will have to do more testing with H4350 powder to see if larger samples will continue to show that improved performance when the samples are statistically meaningful.


    Bullet H4350 IMR4451 IMR4350 RL-17
    130 TMK 0.255 0.349 0.392 0.296
    140 ELD-M 0.286 0.350 0.409 0.558
    142 SMK 0.341 0.353 0.363 ---
    147 ELD-M 0.320 0.378 0.367 ---
    0.300 0.358 0.379 0.401
    Difference --- 0.057 0.079 0.100
    % Difference --- 19.1% 26.1% 33.4%
    Up until these two sessions with H4350 powder, IMR4451 powder led the performance results with an overall average of 0.355 (when the 45 in.-lbs. torqueing anomaly is removed from the comparison).
    Since the H4350 results were 0.300 with the Oryx chassis, it may be more meaningful to compare the IMR 4451 results shot with the Oryx chassis to the impressive H4350 results as in shown in the following table. All the bullet weights that were shot with the same exit time and essentially the same jump to the rifling (adjusted by a few thousandths to accommodate variations in trim length).

    Oryx Chassis Sorted by Bullet Weight and Powder
    Weight Powder Average Median St Dev # Grps Diff. % Diff
    130 H4350 0.255 0.247 0.029 4
    TMK IMR4451 0.331 0.345 0.031 4 0.076 29.6%
    140 H4350 0.286 0.282 0.040 4
    ELD-M IMR4451 0.349 0.344 0.070 12 0.063 22.2%
    142 H4350 0.341 0.329 0.027 4
    SMK IMR4451 0.345 0.367 0.056 12 0.004 1.1%
    147 H4350 0.320 0.326 0.049 4
    ELD-M IMR4451 --- ----- ----- --
    All Weights H4350 0.300 0.309 0.048 16
    IMR4451 0.344 0.348 0.058 28 0.044 14.7%

    Note: I never shot IMR4451 powder with 147 gr ELD-M bullets in the Oryx chassis since I had run out of the 147 gr ELD-M bullets and I didn’t get a new supply until the H4350 powder arrived. For the July 16th session, I doubled up on the 140 ELD-M bullet loads. I guess I may have to revert to IMR4451 to shoot the 147 gr ELD-M bullets to complete the comparison on performance on the Oryx chassis.

    The 142 gr SMK performance with the H4350 powder may have been caused by shooter induced variation. I would have expected the performance of H4350 compared to IMR4451 powder to be bullet weight insensitive. The groups with the 142 SMKs using H4350 powder had three groups with one group that was mediocre to poor, which is not typical for my shooting. I generally have at least one good group in a set of 4 groups with one mediocre to poor group. At a busy range, where I know just about all the regulars, it is not unusual to get interrupted as shooters come and go. It is also possible that I rushed one group to get it in before a cease fire.

    I intend to shoot more of all the bullet types and weights with H4350 powder to see if I can get a better statistical sample.

  21. #21
    Basic Member
    Join Date
    May 2019
    Location
    Northern VA
    Posts
    62
    Hi, CF - I am also in NoVA and i was wondering whether you are shooting at Elite or another 100-yard indoor range for your tests? Thanks!

  22. #22
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    Chris3.Drums

    I shoot outdoors on the 100 yard Rifle-Pistol range at the Arlington-Fairfax Chapter of the Izaak Walton League in Centerville.
    I'm a RSO at that range as well.
    Unfortunately, we don't have the space to extend the range out to 200 or more yards.
    Over the years, the town has grown up around us and eliminated any chance of expansion. But it surely is convenient.

    You don't often get 9 mph winds indoors, even when the air conditioning is on full.

  23. #23
    Basic Member
    Join Date
    May 2019
    Location
    Northern VA
    Posts
    62
    Quote Originally Posted by CFJunkie View Post
    Chris3.Drums

    I shoot outdoors on the 100 yard Rifle-Pistol range at the Arlington-Fairfax Chapter of the Izaak Walton League in Centerville.
    I'm a RSO at that range as well.
    Unfortunately, we don't have the space to extend the range out to 200 or more yards.
    Over the years, the town has grown up around us and eliminated any chance of expansion. But it surely is convenient.

    You don't often get 9 mph winds indoors, even when the air conditioning is on full.
    LOL - I was wondering about the cool range temperatures and wind when it has been crazy hot lately. That explains a lot. I didn't know there were any outdoor ranges in the Centerville area, so I will have to look up the IWL. Thanks for the info!

  24. #24
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    I generally shoot in the morning when the range opens so the temps are cooler and the winds are minimal.
    On Aug 12th, I was RO in the afternoon and got to the range at 10 AM so I could shoot the 12 FV 6.5mm CM before I took over the range. The winds were 8-9 mph.
    I generally don't shoot when there are people at the range but Monday afternoon was really light and there were two shooters who I knew to be safe so I also got to shoot my 12 FV .223 which reported on the other thread on this forum.

  25. #25
    Basic Member
    Join Date
    Sep 2018
    Location
    Northern VA
    Posts
    802
    The following are the results shot with the 12 FV 6.5mm Creedmoor in the new Oryx stock in Northern Virginia on Friday and Saturday mornings, August 16 & 17 at 100 yards. Temperatures were from 73 to 78 degrees with winds from 3 to 5 mph. Altitude of the range is 250 feet above sea level.

    During the sessions I interchanged this rifle with my Oryx stocked 12 FV .223 when the barrels in each rifle heated up. I never allowed the barrel temperature to exceed 135 degrees, measured on temperature strips affixed to the barrels of both rifles. The 6.5mm Creedmoor’s barrel temperature would rise from about 85 to 130 degrees after just 5 or 6 shots. The .223’s barrel temperature would rise from 85 to 130 degrees after from 13 to 15 shots.

    I decided to test the performance of H4350 versus IMR4350 powder with 147 grain Hornady ELD-M #26333 bullets. All the groups were shot with a NightForce 8-32x56mm Benchrest scope. All rounds were shot using Lapua brass and CCI BR-4 primers. All loads were set up to match the 12th reflection time of 1.361 msec. which should be the ‘sweet spot’ for the 26-inch barrel with a 0.040 recessed crown. The action screws were torqued to 60 in.-lbs. per the Oryx directions prior to this session.

    The load description field shows the powder and charge, the O.A.L., the trim length, and the bullet exit time from the 26-inch barrel.
    # Grps. Load Description Bullet Weight Velocity Average Median St Dev 1 2 3 4
    3 IMR4350 40.8 gr 2.840 1.907 wf 1.361 * 73/73 deg. F. 60 in.-lbs. Oryx CCI BR-4 Hornady ELD-M #26333 147 2660 0.344 0.343 0.074 0.270 0.418 0.343
    4 IMR4350 40.8 gr 2.843 1.904 wf 1.361 * 75/76 deg. F. 60 in.-lbs. Oryx CCI BR-4 Hornady ELD-M #26333 147 2660 0.338 0.335 0.022 0.317 0.324 0.345 0.365
    4 H4350 41.0 gr 2.838 1.901 wf 1.361 * 77/77 deg. F. 60 in.-lbs. Oryx CCI BR-4 Hornady ELD-M #26333 147 2661 0.243 0.244 0.031 0.210 0.222 0.266 0.272
    4 H4350 41.0 gr 2.335 1.898 wf 1.361 * 80/77 deg. F. 60 in.-lbs. Oryx CCI BR-4 Hornady ELD-M #26333 147 2661 0.306 0.317 0.067 0.222 0.284 0.349 0.369
    15 0.305 0.317 0.062


    The results were mixed, at best.
    The first two loads with IMR4350 powder were shot on Friday morning and the second two loads were shot on Saturday morning.

    The one bad group (0.418) in the first load was the result of trying to adjust the scope to accommodate the different 147 grain bullets after shooting 130 grains at the last session. The nut behind the trigger turned the reticle adjustment the wrong way and paid the price.
    Actually, the results weren’t all that bad overall.

    However, the comparison of IMR4350 and H4350 with the same bullets is interesting.

    Powder ---- AverageMedian -- # Groups
    H4350 ------- 0.274 ---- 0.289 ----- 8
    IMR4350 --– 0.340 ---- 0.340 ----- 7
    Difference – 0.066 ---- 0.051
    IMR4350 had 1 of 7 groups under 0.3 inches.
    H4360 had 6 of the 8 groups under 0.3 inches.
    Not a large sample but still the difference is significant, especially in the average group size difference.

    For all the groups shot to date with all bullet weights, the results are similar.
    Powder ---- AverageMedian -- # Groups
    H4350 ------- 0.292 ---- 0.289 ----- 24
    IMR4350 --– 0.379 ---- 0.376 ----- 50
    Difference – 0.087 ---- 0.088
    Again, the samples aren’t enormous but the quantity of groups makes the results statistically significant.

Page 1 of 2 12 LastLast

Similar Threads

  1. Savage SA ORYX Chassis
    By varget204 in forum 110-Series Rifles
    Replies: 10
    Last Post: 06-12-2019, 09:37 PM
  2. Oryx Chassis Initial Thoughts
    By celltech in forum 110-Series Rifles
    Replies: 38
    Last Post: 05-17-2019, 10:51 PM
  3. Another Oryx Chassis with 12FV but in 308
    By bassman110 in forum 110-Series Rifles
    Replies: 14
    Last Post: 04-18-2019, 05:27 PM
  4. Oryx Chassis
    By mcgradypilot in forum 110-Series Rifles
    Replies: 1
    Last Post: 03-29-2019, 04:56 PM
  5. Possible new budget chassis offering - Oryx from MDT
    By kcb38 in forum 110-Series Rifles
    Replies: 26
    Last Post: 02-02-2019, 10:19 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •