Results 1 to 12 of 12

Thread: Removing lacquer paint from metal on Model 330

  1. #1
    Basic Member Scionti95's Avatar
    Join Date
    Jan 2016
    Location
    Southern edge of Cypress Creek Preserve
    Posts
    35

    Removing lacquer paint from metal on Model 330


    Was gifted a Stevens Model 330 (Thanks to Mad Dog for identifying) and it has a lacquer like black paint on part of the metal that houses the trigger, hammer etc. (Receiver ??) Guess previous owner wanted to cover up some rust or whatever. Wish to remove the paint, but do not know what solvent to use and best application method The metal has what appears to be a case hardened finish and do not want to damage the metal surface. Any recommendations would be greatly appreciated.

  2. #2
    Basic Member BB68's Avatar
    Join Date
    Nov 2017
    Location
    iowa
    Age
    45
    Posts
    257
    My first thought would be to use a heatgun. heat until you see wrinkle and scrape with plastic puddy knife.

  3. #3
    Basic Member Scionti95's Avatar
    Join Date
    Jan 2016
    Location
    Southern edge of Cypress Creek Preserve
    Posts
    35
    BB68: Thank you for your post. Any recommendation on a particular heat gun. Know there are many brands available and if you can guide me in the right direction on a purchase, it would be appreciated. Thank you !!

  4. #4
    Basic Member BB68's Avatar
    Join Date
    Nov 2017
    Location
    iowa
    Age
    45
    Posts
    257
    I have used a few different ones, dont recall any brands. They were focused more toward auto bodyshop usage. I probably dont have to mention this, but youre going to want to practice a little before trying on the gun.

  5. #5
    Basic Member Scionti95's Avatar
    Join Date
    Jan 2016
    Location
    Southern edge of Cypress Creek Preserve
    Posts
    35
    BB68: Will study up on the brands. Am glad You did mention that it would be wise to practice a little before trying on the gun. This would be my first experience with a heat gun, and do not want to create another issue. Thank you again for your help.

  6. #6
    Basic Member
    Join Date
    Oct 2015
    Posts
    567
    Try Harbor Freight for a heat gun, not
    professional
    grade but perfect for hobbyist and won't cost an arm and a leg. https://www.harborfreight.com/catalo...2Cf&q=heat+gun

  7. #7
    Administrator J.Baker's Avatar
    Join Date
    Dec 2006
    Location
    NW Ohio
    Age
    49
    Posts
    6,409
    Make sure you remove the buttstock and forend from the gun before you put heat to it. Wouldn't want you inadvertently charring it or bubbling up the finish.
    "Life' is tough. It's even tougher if you're stupid." ~ John Wayne
    “Under certain circumstances, 
urgent circumstances, desperate circumstances, profanity provides a relief denied even to prayer.” —Mark Twain

  8. #8
    Basic Member Scionti95's Avatar
    Join Date
    Jan 2016
    Location
    Southern edge of Cypress Creek Preserve
    Posts
    35
    Big Al1: Thanks for the tip on Harbor Freight. One located about 4 miles from my house. Do not want to put a lot of money into it, as this may be a one time use only. Appreciate !!

  9. #9
    Basic Member Scionti95's Avatar
    Join Date
    Jan 2016
    Location
    Southern edge of Cypress Creek Preserve
    Posts
    35
    J. Baker: Appreciate the suggestion in removing buttstock and forend. I can easily see where the extreme heat would bleed over to the wooden pieces. Going to follow your advice and your quote from John Wayne. Don't want to be stupid. Thank You !!

  10. #10
    Basic Member
    Join Date
    Oct 2015
    Posts
    567
    Might as well grab a cart when you go to HF!! That place is the Devil!! You'll find stuff you didn't know you needed!!

  11. #11
    Basic Member
    Join Date
    Dec 2006
    Posts
    3,356
    If it's lacquer paint, lacquer thinner will dissolve it.
    "As long as there's lead in the air....there's still hope.."

  12. #12
    Basic Member Scionti95's Avatar
    Join Date
    Jan 2016
    Location
    Southern edge of Cypress Creek Preserve
    Posts
    35
    sharpshooter: Pretty certain it is a lacquer paint. Had considered the thinner, but was concerned it may etch or discolor the finish. Appreciate your post. Going to study this a little more.

Similar Threads

  1. MkII boyda and paint, 93r17TR paint
    By Lorenzo in forum Picture Post
    Replies: 3
    Last Post: 06-30-2015, 11:06 PM
  2. Trouble removing smooth barrel nut from model 11
    By TheHebs in forum 110-Series Rifles
    Replies: 3
    Last Post: 06-06-2014, 06:48 AM
  3. Model 25: Removing recoil pad from model 25 Walking Varminter
    By 6x45 in forum Other Savage Centerfire Models
    Replies: 7
    Last Post: 07-04-2013, 04:06 PM
  4. Help removing internal mag box - model 12 VLP (2005)
    By jhelmuth in forum 110-Series Rifles
    Replies: 5
    Last Post: 09-15-2011, 11:07 AM
  5. Removing Camo paint from inside Receiver ?
    By Hylander in forum 110-Series Rifles
    Replies: 2
    Last Post: 03-27-2010, 04:04 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •