Results 1 to 6 of 6

Thread: Torque Tuning Action Screws

  1. #1
    Basic Member
    Join Date
    May 2011
    Location
    Lower Alabama
    Posts
    888

    Torque Tuning Action Screws

    Went to the range today to try some of this torque tuning I've read about. Rifle is an old Savage 110 flat back with a Shilen prefit barrel.
    Loaded up some rounds (338-06) that shot well in 85° weather using Barnes 210 TTSX and IMR 4895. Today temp was 52° and recent experience suggested that I shouldn't expect too much when there is a 30°+ temperature change.

    I started with the front screw torqued at 65" # and the rear screw torqued at 15" #. I shot 3 rounds then increased the torque on the rear action screw by 5"#. Continuing in 5"# increments, it didn't take long to find the sweet spot, at 30"# on the rear screw the group shrank to 3/8" at 100 yards. All other torque values tested above and below 30"# produced poor results by comparison. I felt pretty good about the test but needed to verify the results.
    Resetting the torque of the rear screw to 30"# and moving the target to 200 yards, I fired three more rounds. They were not as good as I had expected but did produced a group of 1/2 MOA. I'm guessing I was getting a little tired and wasn't holding my point of aim very well.
    Long story short (or in summary if you prefer) it appears that torque tuning the action screws is well worth the effort. Can't believe I waited this long to try this, I must be a slow learner.

  2. #2
    Team Savage Stumpkiller's Avatar
    Join Date
    Jan 2018
    Location
    Port Crane, NY
    Age
    59
    Posts
    416
    65"#! That's tight. I work up to 35"# front and back after getting close then moving from front to back repeatedly . Making sure to push hard on the muzzle initially to seat the action snug against the recoil lug..
    "They couldn't hit an elephant at this distance." Last words of Gen. Sedgwik

  3. #3
    Basic Member
    Join Date
    Dec 2014
    Posts
    241
    If I recall correctly, Savage recommends 36. Please check with Savage tech support. Have your serial number handy. They will ask.

  4. #4
    Basic Member
    Join Date
    May 2011
    Location
    Lower Alabama
    Posts
    888
    Should have stated that the action is pillar bedded. I started at 65”# on the front as that is where it has been for sometime now and didnt won’t to start completely over, (too lazy and a slow learner)

  5. #5
    Basic Member big honkin jeep's Avatar
    Join Date
    Mar 2007
    Location
    Metro Atlanta Georgia.
    Posts
    1,947
    I've had really good luck torque tuning as well.
    A good wife and a steady job has ruined many a great hunter.

  6. #6
    Team Savage
    Join Date
    Jan 2015
    Location
    Austin
    Posts
    1,228
    For anyone who's unfamiliar with torque tuning the Savage Action, here's the procedure : http://www.accurateshooter.com/techn...torque-tuning/
    Give a man a gun and he can rob a bank. Give a man a bank and he can rob the world. Never forget what Wall Street did in 2008.

Similar Threads

  1. Mark ii TR .22 Action Screws Torque
    By PeterRocco in forum Mark I, Mark II and 93R Rifles
    Replies: 7
    Last Post: 05-25-2017, 12:07 PM
  2. what torque for action screws.
    By wal0001 in forum 110-Series Bolt-Action Rifles
    Replies: 16
    Last Post: 12-09-2016, 03:24 PM
  3. Torque spec for action screws
    By mj52 in forum 110-Series Bolt-Action Rifles
    Replies: 1
    Last Post: 09-13-2015, 09:52 AM
  4. Torque action screws
    By jsthntn247 in forum 110-Series Bolt-Action Rifles
    Replies: 1
    Last Post: 06-19-2013, 04:30 PM
  5. Torque settings for 110 Action screws
    By chuckc2dog in forum 110-Series Bolt-Action Rifles
    Replies: 4
    Last Post: 03-23-2012, 08:55 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •