110? A .22-250 in a long action? Is it an old J series?
uj
So, i found a good deal on a Savage 110 in 22-250 (kid(s) need something to get started on deer with ;p small tx deer)
Anyway,
it's a 110, flat rear receiver, serial is F493xxx (around 1994/95?).
When did they stop making flat receivers ?
Also the bolt has a spur on the lower right side that i dont recall being present on my Stevens 200.
Is this a 110(x) (E/G/etc) walnut stock with 5 1/8'ish spacing, center feed ?
curious on the model /age as how it affects order parts/stocks.
Thanks
Knickia
**Update*** Here is a picture of the lip on the right hand side of the bolt (gas baffles ?)
Does this indicate it to be a 110(x-something) ? I have not noticed these on any of the 10/110s i have handled.
[img width=337 height=450]http://sphotos.ak.fbcdn.net/hphotos-ak-snc3/hs291.snc3/28227_1261413864700_1510299940_30538033_2961669_n. jpg[/img]
110? A .22-250 in a long action? Is it an old J series?
uj
definately not a short action or a centerfeed mag.
It is definately a staggerfeed, but you'd have to measure the screw spacing yourself to see if it is a true long action(5.00") or a intermediate "J" action(4.522").
”I have a very strict gun control policy: if there’s a gun around, I want to be in control of it.”
~Clint Eastwood
Sorry, yes your right, my brain said staggered, but i typed center, Your correct it's a stagger feed.
I did find this
"The original 110 was a "one size fits all " action typically referred to as the "J" action. They had a action screw spacing of 4.522"
Starting around 1988 the 110 screw spacing became 5.062" and starting around 1998 the short action with a 4.275" spacing.
Now....
There were some long actions ( 5.062") configured as short actions. The magazine opening was cut to accept a short action box with an extended front baffle to shorten the bolt throw ( bolt stop). "
It would appear to be the short action cartridge on a long action as noted, the screw spacing looks right @ 5.062 , my calipers dont open that wide, but a quick check with a tape puts it just over 5".
I "assume" that any 110 stock with 5.062 spacing would fit ? I am thinking i might find a beater stock to hack down to size, or a youth stock for it.
The barrel is stamped with both 110 and 22-250.
So i guess the other real mystery is what the little spur on the bottom right side of the bolt carrier/baffles is (i only have a round rear receiver to compare to so i don't know if this is a normal guide mechanism for flat receivers).
Added photo to original post of the Spur/Lip on the right side of the bolt, left side is smooth...
that keeps the bolt from opening way farther then it has to for a shorter cartridge. it is still used on the 10 series in .223
a lot of barrels also said if they were series "E" or "J" on them. nothing on yours? J started when they went to the changed screw spacing. If your is the 5"+ long action it is older then the J. not a good view of the bolt, but newer then the rifles with the old bolt head.
.223 Rem AI, .22-250 AI, .220 Swift AI .243 Win AI, .6mm Rem AI, .257 Rob AI, .25-06 AI, 6.5x300wsm .30-06 AI, .270 STW, 7mm STW, 28 nosler, .416 Taylor
This rifle looks to be an original 110 from 1958-1963 or thereabouts. Does the barrel have the rear sight dovetailed into a large ring on the barrel? that would be another indicator.
What you have is a long action set-up for a short action cartridge. From 1988 to 1997 everything was made on a long action. An extended baffle was used on short cartridges to limit the bolt travel. The guide fin was added sometime in 1988. The short action 10'and 12's came out late 97-early 1998, they were still flat top rears. The round top actions came out with the Accutrigger in 2003.
"As long as there's lead in the air....there's still hope.."
Nobody answered this question. I would like to know that answer if anybody can tell me.Originally Posted by knickia
Wood
Blue Avenger, is that bolt head cracked at the 7-8 o'clock position???
Curt
It was answered in the post above yours.Originally Posted by 51Bravo
Originally Posted by sharpshooter
No, it is all part of the the extractor and how it fits onto the bolt head.Originally Posted by Netz
"Muzzle velocity is a depreciating asset, not unlike a new car, but BC, like diamonds, is forever."-German A. Salazar
Bookmarks