Page 1 of 2 12 LastLast
Results 1 to 25 of 26

Thread: Savage Target Rifle Build

  1. #1
    Basic Member DeadEyeDeadly's Avatar
    Join Date
    Jul 2014
    Location
    El Paso, Texas
    Posts
    27

    Savage Target Rifle Build


    I'm a new member, and I've started putting together my first ground-up rifle build. Here's the bits & pieces list:


    Savage Target Action – Left Port
    McGowen 28” Stainless Barrel chambered in 6.5 Creedmoor
    Laminated Thumbhole Stock from Richard's Microfit Stocks
    Weaver T-36 Scope utilizing Burris Signature Zee Rings


    Pics of stock modifications so far:


    http://

    Widening of the barrel channel


    http://

    Maple caps attached & rough sanded.

    I'll add more pics as progress is made.

  2. #2
    Basic Member
    Join Date
    Feb 2013
    Age
    48
    Posts
    446
    Right on....

  3. #3
    Team Savage
    Join Date
    Feb 2010
    Location
    Kennedy Meadows,CA.
    Age
    73
    Posts
    4,789
    Looking good

  4. #4
    Basic Member DeadEyeDeadly's Avatar
    Join Date
    Jul 2014
    Location
    El Paso, Texas
    Posts
    27
    Action/Barrel Epoxy Bedded


    I used Loctite Marine epoxy (which is normally white) tinted with pigment to bed my stock. Paste wax was applied to the action and barrel to serve as a release agent. I used mold making clay as dams to contain the epoxy as it was compressed to fill the bedding voids.





  5. #5
    Basic Member
    Join Date
    Apr 2012
    Posts
    24
    Looking great.

  6. #6
    Basic Member
    Join Date
    Sep 2012
    Age
    46
    Posts
    120
    Man, the Maple caps are gonna be very cool. Will definitely be keeping up with this one.

  7. #7
    Hallbilly
    Guest
    Good job.
    Nice to see someone doing his/(Her?) own thing.

  8. #8
    Basic Member DeadEyeDeadly's Avatar
    Join Date
    Jul 2014
    Location
    El Paso, Texas
    Posts
    27
    Polyurethaned Stock

    Here's pics of my stock with five coats of polyurethane applied. I used Rust-oleum semi-gloss polyurethane tinted with Bullard Metallic Pigment (Orchid), which I acquired on the internet from OutKast Fishing Tackle. After the finish has cured for at least a full day, I'll buff it out with extra fine steel wool before mounting the barreled action.






  9. #9
    Team Savage snowgetter1's Avatar
    Join Date
    Aug 2010
    Location
    Illinois
    Posts
    1,135
    Looking real good.

  10. #10
    Basic Member DeadEyeDeadly's Avatar
    Join Date
    Jul 2014
    Location
    El Paso, Texas
    Posts
    27
    Ready for Barrel Break-In


    Overall weight with McGowen 6.5 Creedmoor barrel in Douglas #9 contour comes to ~ 15 pounds. The old bathroom scales gave me readings from 14-16 pounds, even by weighing myself holding the rifle.
    Weather permitting, I hope to break-in the barrel next week.








  11. #11
    Team Savage
    Join Date
    Feb 2010
    Location
    Kennedy Meadows,CA.
    Age
    73
    Posts
    4,789
    Outstanding!!!

  12. #12
    Basic Member
    Join Date
    Feb 2013
    Age
    48
    Posts
    446
    Absolutely.... Good luck with the initial outting!!!

  13. #13
    Basic Member DeadEyeDeadly's Avatar
    Join Date
    Jul 2014
    Location
    El Paso, Texas
    Posts
    27
    I managed to break-in the barrel despite temperatures in the 40's and winds gusting to 35 MPH, as the itch to test this rifle was too great to wait. Initial windage was 12 inches to the left and 2 inches high at 100 yards. I got a crick in my neck because the scope needs to come back just a tad, so I placed a Weaver extension base on order. I also want to get a .010 Eccentric (offset) insert for the Burris scope ring to bring the Weaver T-36 closer to center of windage adjustment, but everywhere I found that carries them so far are “Out of Stock”. So, I placed them on back order at two places.

    I've loaded some 107 grain Sierra Match BTHP bullets, as well as some Hornady 100 and 120 grain AMax bullets to begin load testing when the weather is more favorable.

  14. #14
    Basic Member DrThunder88's Avatar
    Join Date
    May 2013
    Location
    Metro Detroit
    Posts
    1,383
    Well done!

  15. #15
    Team Savage
    Join Date
    Dec 2006
    Location
    125 miles North of San Francisco
    Age
    81
    Posts
    1,485
    And who says Richard's Micro-Fit Stocks are junk? Turned out real good!! One question. Are your pillars below the surface of the bedding? (just wondering) May be an issue if the bedding ever compresses.
    Still a nice looking job.
    Oz never gave nothing to the Tin Man, that he didn't already have.

  16. #16
    Basic Member DeadEyeDeadly's Avatar
    Join Date
    Jul 2014
    Location
    El Paso, Texas
    Posts
    27

    Action Bedding

    Thanks to all you guys for the compliments!
    The Richard's Micro Fit Stock was a very good fit for the action, and required only the removal of a small amount of laminate in the bolt release area to attain proper operation.The barrel channel requires extensive work for heavy barrels.
    The pillars are below the bedding surface of the action. The Loctite Marine epoxy is rated at 3,000 PSI, so I predict that there will be very little compression happening over time.



    For anyone interested, here's a brief description of my action bedding procedure ( refer to the pic for details):


    I constructed my bedding tool from 1 inch PVC pipe which is just slightly smaller in diameter than the Target Action. I placed the tool with coarse grit sand paper secured with tape into the action channel and rotated the handle from side-to-side. I added more layers of sand paper in progressive steps to widen the channel to the desired size.
    I formed my shims into semi circles and super glued them into the channel. When the barreled action is bolted into the stock and the excess Marine epoxy is squeezed out, there is minimal mess, as it is very viscous. After the action epoxy was cured, I repeated the procedure for the barrel pad minus any shims (the action pad provided the proper clearance).



  17. #17
    Basic Member
    Join Date
    Dec 2014
    Posts
    25
    Excellent! What did you use as a release agent? Was it difficult to remove?

  18. #18
    Basic Member DeadEyeDeadly's Avatar
    Join Date
    Jul 2014
    Location
    El Paso, Texas
    Posts
    27

    'Smack' Release Jig

    I used automotive paste wax as the release agent. Two applications is enough, but the first coat needs to cure for about an hour before the second is applied, then lightly buff.
    I slid nylon reinforcing strapping between the stock and barrel, placed my 'Smack' Jig over the barrel (the side rails are supported by the stock, the 'Smack' Zone cross member sits ~ 3/8” above the top of the barrel), suspended the whole conglomeration by the strapping, then smacked the 'Smack' Zone with about an 18” piece of 2X4 - - the stock pops off quite easily! See pic . . .




  19. #19
    dcloco
    Guest
    Very nice! Cannot wait until you wring this out without the 35 mph W word!

  20. #20
    Basic Member
    Join Date
    May 2011
    Location
    Lower Alabama
    Posts
    1,091
    I love the "Smack Jig", going to have to build me one of those.

  21. #21
    Basic Member DeadEyeDeadly's Avatar
    Join Date
    Jul 2014
    Location
    El Paso, Texas
    Posts
    27

    Target Pic

    I managed to fire six 5 shot groups today. I think that the front screw on my front scope base may be bottoming-out on the barrel threads before becoming completely tight (didn't seem quite right when I installed the front extension base), as the groups were wandering to different points-of-impact. Will check on that tonight. Anyway, here's a scanned pic of the best group:





  22. #22
    Basic Member Robinhood's Avatar
    Join Date
    Apr 2014
    Location
    South Texas
    Age
    66
    Posts
    7,784
    Very nicely done.

    What is your twist rate?

  23. #23
    Basic Member DrThunder88's Avatar
    Join Date
    May 2013
    Location
    Metro Detroit
    Posts
    1,383
    Excellent group!

  24. #24
    Basic Member DeadEyeDeadly's Avatar
    Join Date
    Jul 2014
    Location
    El Paso, Texas
    Posts
    27
    Quote Originally Posted by Robinhood View Post
    Very nicely done.

    What is your twist rate?
    1 : 8.5"

    I replaced the screw in the front scope base, and it then tightened correctly.

  25. #25
    Basic Member DeadEyeDeadly's Avatar
    Join Date
    Jul 2014
    Location
    El Paso, Texas
    Posts
    27

    Latest Test Load

    alphapygmy sent me some mismatched Burris ring offset inserts (that I modified by applying tape to the inner surfaces to get them close to being a matched set) to alleviate a gross windage problem I had. It seems to be working OK. Only time will tell if the scope will retain it's POI as currently adjusted. I'm satisfied that I have a shooter - - now to get serious about load development. Here's a pic:






Page 1 of 2 12 LastLast

Similar Threads

  1. Savage Axis II XP as an entry-level target rifle?
    By Bruin06 in forum Axis Series Rifles
    Replies: 4
    Last Post: 04-13-2016, 06:27 PM
  2. Target rifle build .308
    By GSXR in forum Competitive Shooting
    Replies: 3
    Last Post: 06-10-2013, 07:44 AM
  3. Questions about a Target Rifle build
    By jsthntn247 in forum 110-Series Rifles
    Replies: 1
    Last Post: 04-11-2013, 08:04 PM
  4. Replies: 11
    Last Post: 12-24-2011, 02:01 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •