Reply With Quotemybe you got the screws backwards
drybean
HS Precision, bolt not opening, torque and assembly spec
I was wondering if there were some answers to my problem.
Well I have the model 10 with the HS precision stock that it came with from the factory and I took the gun apart to clean it and see whats going on in there. The screws came out at 40in lbs. After I assembled it, i went to rack the bolt and it moves up fine, but will only move back maybe 1/8inch. I then tried lowering the torque setting and no change. I've tried front screw first then the back screw and vice versa. The only way to get the bolt to function properly is with less than 10in lbs on the rear screw and the front screw doesnt matter. To me, this cant be right at all. I only use quality factory ammo and have put maybe 30-40 rounds through it. So my questions for all of you are, what am I doing wrong? What should be checked? And what is the assembly procedure and torque settings for this rifle?
I'm just really confused. Any help is appreciated. Thanks.
mybe you got the screws backwards
drybean
Check your scope mount screws. If they are too long, the front ones can protrude into the area of the bolt head. Try removing them and see if that changes anything.
I had this problem with my rear screw. Just shortened the screw a couple of threads and it works fine now.
Yep, you have a screw in the wrong place. Check the lengths of the srews on top and on bottom.
I just encountered this very problem after bedding my hs precision stock. In the process of relieving the being block for adhesion of the Devon, it allowed the receiver to sit where it was meant to sit (flush with the block where the screws are). This resulted in an extra half thread protrusion into the receiver of the rear action screw. When i installed the barreled action i had the bolt installed and that little bit of extra length was just enough to keep me from pulling the bolt back. I could cycle it fine to Recock it but couldn't extract it.
Bottom line, remove about a half thread length from your rear action screw and you'll be fine. I promise...
A thin washer would confirm this fix before cutting your screw.
Even taking a whole thread length should not matter.
But not positive ?
I had to do the same thing to a Savage ML.
PSE EVO 60 Lbs.
Blacked out
Even more simple than that, just loosen the rear action screw a turn and see if the bolt frees up...
I would like to here back from the OP to see what the prom. was
drybean
Wouldn't we all. Nothing more frustrating than hearing about a problem and not getting updated as to the solution. I'm confident it's just that the rear screw needs to be shortened but wanna see if I'm right
yes did that once myself...works wonders if you switch em around
Did what? Swapped action bolt screws on accident? That would be impossible on this particular model. Difference in length is like 3/4"!Originally Posted by ww1rdb
ok am not familiar with newer models but on older ones one screw hole was picky and if you used the wrong screw it would keep bolt from opening if you had it tight..sorry if I mis read anything...maybe I am thinking of something else..
Yeah, older models seem a bit finicky
exactly......My model 10 has a HS stock on it and the action screws are hard to get mixed up.
Ive been scratching my head on this one. If the only thing that was done was a simple removed and install of the stock with no milling/grinding of the bedding alum. bedding block on the stock, then there sould be no problem what so ever with a reinstall. considering he only has but 30-40 rds thru the thing?Im wondering if "that" particular HS stock on his model came with a spacer?...I dunno, but something,s a miss here...lots of speculation on this one for sure
Ok everyone. Sorry to keep you waiting, i havent been home in a few days to check out the problem.
But the problem was the rear screw being a bit too long. Maybe i had some bolt stretch?(i dont know how) It had a very small shoulder on the end of it, so i filed it down to where the threads start and now it works like a charm.
Thank you all for the input.
So now to start another debate. What should be the torque setting be? I know it came with 40in lbs, but i see alot of debate about setting it to 65, on this site and other sites. Does it matter as long as they are the same or should i play around and see if there is a sweet spot?
Ok everyone. Sorry to keep you waiting, i havent been home in a few days to check out the problem.
But the problem was the rear screw being a bit too long. Maybe i had some bolt stretch?(i dont know how) It had a very small shoulder on the end of it, so i filed it down to where the threads start and now it works like a charm.
Thank you all for the input.
So now to start another debate. What should be the torque setting be? I know it came with 40in lbs, but i see alot of debate about setting it to 65, on this site and other sites. Does it matter as long as they are the same or should i play around and see if there is a sweet spot?
am waiting to hear that answer also...in fact have asked it in my thread..I know i read it years ago and wish I had made a copy.. it has a specific order to tighten the screws and how many foot pounds..
as I remember it said if it wasn.t done properly it could split the stock..I had a 110CL (older rifle) that had that problem and it had split the stock from the front screw hole to the metal floor plate where the clip feeds in...either I am blind or it hasnt been discussed..only thing I could find was for the AXIS...so have fingers crossed you get an answer
Oh, thats no good.
I just figured someone, somewhere would have an answer to that. All i have found is specs for other rifles as well.
If you have a plastic stock and you are torquing it to 40 in/lbs and all of the sudden your screw is sticking up into the action. Now you are wondering if you need to tighten it more maybe you should stop and think for a minute! You are pulling the screw through the stock for christ sake. Your gun my shoot great at 20 in/lbs but now that the stock is all extruded and tweaked it may not ever shoot right untill you replace the stock. Just a thought.
I was asking about a wooden stock...guess you didnt read what I asked..and yes it was a problem with some older guns where they werent tighted right and the stock split from recoil..I have never had trouble with screw into the action but have had a stock split..but thanks anyway
And my stock has the aluminum block in it so it shouldnt be a problem, unless i split the aluminum, but it looks like the bolts will stretch before that happens. Haha.
I have one just like yours.
I do 65 in. Lbs.
PSE EVO 60 Lbs.
Blacked out
I always do 60-65 in/lbs.
Members who have read this thread in the last 1 days: 0
Posting Permissions
Bookmarks