3/4 to 1" really isnt that bad, especially if its a new gun. But anyways, what load are you using? Whats the twist? what bullets and powders do you have on hand?
Need some loads to try in this gun cannt seam to get it to do any better then 3/4" to 1" I would thing that it would shoot better then that but maybe no
3/4 to 1" really isnt that bad, especially if its a new gun. But anyways, what load are you using? Whats the twist? what bullets and powders do you have on hand?
It's not bad but I really think it would give 1/2". Bullets are nos 40gr btip, 55 gr Sierra btip, vmax 40 gr, 55 gr nos btip, powders at win 748, imr 8208, Hodgdon varget
Looks like you need some H4198. My load for the 40gr is 22.7gr of H4198. The 55gr is 20.3gr of H4198. Ive used Varget and 8208 and couldnt achieve the accuracy that I could with H4198 on the smaller bullets. Benchmark is also one that I found was a great powder for the small bullets but was getting hard to find locally.
...I only use BenchMark in my .223's.. 55gr Nos. BT on top of 26.1grs of BM, CCI-400prs, Win. brs.
![]()
theres that dang paper plate again.lol Howd you get the orange marker to cover up those powder burns?
...It's kinda tricky...Originally Posted by keeki
![]()
Thanks guys I'll try it would love to get it to shoot like that even if all it is a dog gun
Ps the wife got it for me so if it shot 3" id have to keep lol
All these loads are accurate to 200+
55 Nosler BT
25.5 Varget
CCI 450 Primer
55 Nolser BT
25.5 8208XBR
CCI 450 Primers
40 Grain bullet
27.5 W 748
CCI 400
What twist rate dies your rifle have? Some savages in the varmint contours have a 1:9 twist. If so, 55 gr would be the lightest for me. I would even consider a 62 or 69gr bullet. My FCP-K shoots .4" with 55gr federal premium loaded with nosler ballistic tips. I don't reload as of yet.
My model 11 seems to have a strong preference for Rem 55JSP over 20.2 gr. of IMR4198. Best shooting load that I found after hours at the bench and running test loads. Ragged cloverleaf at 100 yards and accurate out to 200.
1shot,
That group is almost as awesome as your avatar. Almost... :)
.You know the old saying...A picture is worth a 1000 words..Originally Posted by barrel-nut
![]()
26.9 grains varget 55 grain V Max
Shoots very well in my .223 Predator
Bullet is jammed tight into the lands.
If its a 1 X 9 twist, you ought to try some heavier bullets.
My Savage bvss shoots 77 SMK into one hole at 100 yds. It likes 24 gr of varget and Rem 7 1/2 primers.
TTT
PSE EVO 57 Lbs.
Blacked out
On or off the lands?Originally Posted by seanhagerty
PSE EVO 57 Lbs.
Blacked out
Try 69 gr SMK 25.8 Varget, Hornady or Win brass, CCI BR primers, .015 - .020" jump.
75gr Hornady HPBT 24.2 Varget Hornady brass, CCI BR primers.
Disclaimer: 25.8 is near Lee and Hogdon max listed. Work up slowly yada yada.
This is in a 10FCPK bolt gun .223 and is validated to 403 yds via Nikon 440 laser range finder.
It (25.8 load)has no vertical without some help in my gun. It shot 5 shots inside 3" w/2 fliers@ 403 yds off Harris bpod. It shot 3/4"@ 100 yd. Im on iPhone will try a target pic if you're interested. Can't resize target pic prior to posting from iphone.
Hope the info helps you.
I've had a chance to do some testing of reloads for my new Savage Model 10 Precision Carbine
So far I've just been using Varget powder and two different bullets. The Sierria Match King 69gr. Hollow point BT's, and the Hornady Match Bullets 68gr. Hollow point BT's.
Thus far my results have been: BTW--the orange dot is 1" & all rounds fired at a 100yd target.
Hornady, 24.5gr. Varget
Hornady 24.7gr. Varget
Hornady 25.0gr. Varget
Sierria 24.5gr. Varget
Sierria 24.7gr. Varget
[img width=572 height=768]http://i12.photobucket.com/albums/a212/davemuzz/8a4ec747.jpg[/img]
From my initial testing (which I did not post any pictures) it appeared the Hornady's had the most promise. However, it wasn't until I shot the last 5 round group of Sierria's with 24.7gr. of Varget that I got the best 5 shot group of .755. So, I'm going to bump the powder up just a bit more and perhaps give it just a little more OAL and see what happens with the Sierria's. For the Hornady's, I'm going to bump the charge up to 25.2, and extend the OAL enough so the round fits the mag, and also lets the powder not crunch when the bullet is seated. (No compressed load)
Dave
Dave, I know all guns are different but I noticed a target you had that looks similar to a 69SMK load of mine @ 125 yds. It is the one in the upper left under the "69".
It is the 25.8 load I mentioned in my previous post above and it looks like your 24.5 gr load.(you may want to look @ that load @ 400 yds.)
Here is the target of the same load @ 403 yds. that I mentioned above in a previous post when I was on Iphone and couldn't do a pic. Inside 3"@ 400 yds w/2 fliers, but inside 1.8" without the 2 vertical fliers.
No vertical(except for my 2 fliers) The holes marked with the "l" not the holes marked with an "x", they were 75 gr. The blue circle is 3", squares are 1"
Anyway may be of some help developing a yote load if you need the legs for 400+ yds.
Fliers? No such thing!!! Back to the drawing board.
My 223 Predator likes 24 or 25gr of Varget CCI 450 55gr Nosler BT also try 73gr bergers with 23.5 Benchmark cci 450!
I loaded some 69 grain SMK with 25 grains of IMR 4320 today that shoots great in my Stevens mdl. 200.In my Precision Carbine it likes 50 grain Nosler ballistic tip with 26grains of Accurate 2230.But both rifles shoot everything good.Just can't beat a Savage for out of the box accuracy!
Jeff
funny how a nice sharp pencil will make a perfect round bullet hole.aint it....lol
I just had to say it...lmbfao
Bookmarks