Axis Issues, need some help!

Hello all,
I work at a small gun store/outdoor store and we sell Savage. We have had issues with customers purchasing Axis in 22-250 and the bolt not fully closing on a round therefore they can not use it. So instead of having this to deal with, (upset customers) we figured if we had a piece of fired brass we could slide it into the chamber and make sure the bolt will close before it leaves the store. We tried this with two of the new Axis and both pieces of brass are in the chamber, but the bolt is stuck forward and it won't come back. One will close on the brass, the other will not. The issue now is how do we get the piece of brass out of the chamber? Is there something I am missing here? I have a Stevens 200 and I have put an old piece of brass into the rifle to practice dry firing and never had this happen. Any help would be greatly appreciated. I am working this weekend and would like to get it resolved then. Thanks a ton,

1ShotKing

Was the brass shot from these rifles, or was the brass FL sized BEFORE you tried them in these rifles?

If not that is why it is stuck, it was fire formed from another rifle.

See if you can get a cleaning rod to assist you to get them out

Unfortunately, it was fired from a different rifle. That is something I knew just somehow managed to overlooked it completely. So that is the reason why it is stuck. How do I get it un-stuck?

1ShotKing

If the bolt will rise, I would run a cleaning rod from the muzzle end and GENTLY hammer on the rod

If the bolt will not rise, you will have to dissemble it to remove it

Anyone else have a better suggestion?

The bolt will rise on both. I will try the cleaning rod suggestion, how hard should I go before trying something else? If there are any other suggestions I'm all ears. Thanks again,

1ShotKing

Quote:

---

Originally Posted by 1ShotKing

The bolt will rise on both. I will try the cleaning rod suggestion, how hard should I go before trying something else? If there are any other suggestions I'm all ears. Thanks again,

1ShotKing

---

Hard to judge that not being there... I would not fram it like you were driving a 10d nail in pure fat lighter! You might want to spray some Rem oil or such in the chamber and pull the mag and spray some in there on the bolt to help out some.

Wood dowel works good, too. The case is stuck & the barrel is hardened steel. using a brass or aluminum rod won't hurt it.

Slide it in there & give it a good smack. It'll come out.

Don't forget the traditional swear words..... You may have to make up a new or two.

Frank you for got somethink there.

That was fgw in Fla LOL ;-)

How did it work out 1ShotKing, did you get the brass out??

Didn't try it yet, I've been in school all day. I'll be at work tomorrow morning bright and early I'll let you know how it goes. Thanks again for your help.

1ShotKing

Got both of them out. One took a little more persuasion but nothing serious.

1ShotKing

I had the same problem with my new Edge in .223, I have another savage in .223, A model 10, So before I got the Edge I went and reloaded 500 hundred rounds
with 55 grain Hornady V - Max, The only problem was I only neck sized the Winchester Brass from the Model 10, I had sold it to a friend because he wanted it for
the heavy target barrel it had on it. I wanted the lighter barreled gun, Easier to carry through the fields after wood chucks. When I went to sight in the Edge with
the rounds fire formed to the Model 10 my bolt would not work either. It had me stumped for a while until I went back through my reloading notes and remembered
I did not full length resize the cases, No way would they work in the Edge, Took apart 500 rounds, Full length resized the cases, reloaded them and now they work
fine. Take Care, Everyone and shoot straight..... Lockwoodjohn

Quote:

---

Originally Posted by lockwoodjohn

So before I got the Edge I went and reloaded 500 hundred rounds...

---

Wow! My math makes that out to be 50,000 rounds. LWJohn, you win the prize for being one dedicated reloader. ...and confident, too! :first:

Quote:

---

Originally Posted by 1ShotKing

Got both of them out. One took a little more persuasion but nothing serious.

1ShotKing

---

Glad it worked out for ya! You can FL re-size them and all will be well.

i am sure i am missing something
& my math is not great,but were do you get 50,000 rds

drybean

I think it was from lockwoodjohn wrote

Quote:

---

reloaded 500 hundred rounds

---

Which is 500 x hundred

Quote:

---

Originally Posted by fla9-40

I think it was from lockwoodjohn wrote
Which is 500 x hundred

---

+1
Sorry for the confusion, was simply having a gentle chuckle at Lockwood John's typo.

Quote:

---

Originally Posted by thomae

+1
Sorry for the confusion, was simply having a gentle chuckle at Lockwood John's typo.

---

"confusion".....what confusion??? Do I look confused? :wacko:

If you can't have fun, might as well pull the dirt in around ya!

drybean you are right on to question the math,

First time 500 rounds, All new cases, bullets,powder and primers.Shot them all through the model 10, Them reloaded them (neck sized only) Tried to shoot them
through Edge, No go! Took 495 bullets apart along with the 5 I did manage to shoot through the Edge and F/L re-sized them and reloaded them. Now they shoot
through the Edge fine.
lockwoodjohn ( by my math that is 1500 bullets but only using the 500 original cases, The Gentlemen might be using that new Math they teach in places of higher learning like at Cornell U. )

Sorry for the typo I did not even catch it after reading it 3, That is one , two, three times It Was ONLY 500 X 3 different times.

LOL lockwoodjohn