Looking for input on an aftermarket stock for my model 10TR in .308

Printable View

10-05-2015, 03:23 AM
Newbe

Looking for input on an aftermarket stock for my model 10TR in .308

Hey guys, thanks for taking the time to read my ramblings and help me out with a new stock.

Shooting prone has been tricky to say the least with my factory Savage Model 10TR in .308

It seems even the slightest change in load on the bipod throws my shots turning groups into large patterns. Shooting off the bench results in a 3-4" upward shift in POI.

A nice fellow at the range today said it was probably the Accustock flexing too much. I thought the Accustock was supposed to be a good rigid platform?

Anyways, he suggested I get an aftermarket stock (Bell and Carlson M40, etc) in order to eliminate or at least greatly decrease the variability caused by the factory stock.

Any suggestions for an aftermarket stock?

Should I get one with an adj cheek piece, or just use my Karsten adj cheek piece that is currently slipping down on the factory stock?

Thanks for any and all input on this! I greatly appreciate it!:eagerness:
10-05-2015, 10:09 AM
mikgarus

I switched the Accustock on my Mod 10 PH Max 1 to a B&C M40. Although I love the feel of the stock and everything else, in my case it didn't make it any more accurate.
10-05-2015, 12:13 PM
jbjh

Looking for input on an aftermarket stock for my model 10TR in .308

The Accustock is decent enough for where the action sits, but upfront it flexes a bit more than it should.

If you search the site, you'll find instructions on hogging out the front end, and epoxying aluminum arrow shafts to stiffen the forend.

Otherwise yes, most every factory rifle will benefit from an aftermarket stock. Lots of good ones out there, making it fit you is the big trick.

Personally, I love my Manners stock, but for the money, it's hard to beat the B&C offerings. There are several chassis on the market that do a great job, without spending a lot of extra money for bottom metal.
10-05-2015, 10:02 PM
CharlieNC

Choate is as rigid as they come, as the alum bedding block extends into the forend.
10-06-2015, 11:01 AM
big honkin jeep

I suggest that if your accustock is flexing, then dont have an elephant sitting on it when you shoot.

I would guess something else is inconsistent.
10-06-2015, 01:54 PM
Newbe

Quote:

Originally Posted by big honkin jeep

I suggest that if your accustock is flexing, then dont have an elephant sitting on it when you shoot.

I would guess something else is inconsistent.

I'm actually looking at a couple of different possibilities. Glad to hear you are confident in the Accustock's abilities. I don't want aftermarket if I don't have to.
10-09-2015, 12:05 AM
Newbe

Ok, update. I was being a dumbass and causing a burr to be drug up from the bottom of the bullet upon seating. I thought it was a burr on the brass, but after closer inspection, it was copper from the bullet jacket. I went ahead and dumped all of the powder out that I'd already weighed, and proceeded to chamfer the mouth of every case. Wallah! The problem went away.

Weird thing is, I didn't chamfer any of these cases last year when I loaded them up, and there was no problem. The Lapua brass actually looked as if it already had a chamfer on it, but apparently not enough.

So, just an update, problem solved.
10-09-2015, 12:02 PM
minnesotamulisha

Last year when you loaded them, was the brass new? I chamfer every time I load just to eliminate error and keep things consistent.
10-10-2015, 10:59 PM
gemby58

Quote:

Originally Posted by jbjh

The Accustock is decent enough for where the action sits, but upfront it flexes a bit more than it should.

If you search the site, you'll find instructions on hogging out the front end, and epoxying aluminum arrow shafts to stiffen the forend.

Otherwise yes, most every factory rifle will benefit from an aftermarket stock. Lots of good ones out there, making it fit you is the big trick.

Personally, I love my Manners stock, but for the money, it's hard to beat the B&C offerings. There are several chassis on the market that do a great job, without spending a lot of extra money for bottom metal.

I use carbon fiber tubes for this a lot stiffer than arrow shafts
10-12-2015, 03:41 AM
Newbe

Quote:

Originally Posted by minnesotamulisha

Last year when you loaded them, was the brass new? I chamfer every time I load just to eliminate error and keep things consistent.

Yes, it was the exact same brass, never fired. I had them loaded up, but with charges that were too high. I pulled all of the bullets and powder, and re-charged the cases with a lower powder charge, and re-seated the bullets.

I thought the virgin Lapua brass was already chamfered, since it kind of looked like it, and I never shaved any bullets last time.
10-26-2015, 08:23 PM
mattri

As you fire and reload the cases be sure to check length and trim as necessary. Trimming will obviously remove the chamfer. Lots of folks, myself included, do a quick check, trim and chamfer after every firing, just part of the process.
10-27-2015, 03:16 PM
luc voyer

Take a look at the MDT, I just put mine in the HS3 chassis and there is a world of difference. I'm done with the flex that came with the original stock.
http://mdttac.ca/hs3-chassis-system.html