I installed the trigger following all of the instructions and everything worked great
then I hit a snag I cannot get the bolt out tried everything the sear will not move far enough into the trigger housing
took it apart put it together without the trigger and no problem put the trigger and the arm back in and no good
not like I take the bolt out every day but
This was meant to go out as guestion looking for suggestions
Is this a top bolt release? If it is, the sear has to travel at least that far when it fires. It cannot hang up like you say when you pull the trigger or I don't believe it would fire.
If it is a bottom bolt release I think I read where Robinhood made one work with the sav2. But I've never worked with that combo.
top bolt release and the sear travels pleanty far enough to fire but it needs a 1/8 more travel to release the boltQuote:
Originally Posted by mnbogboy2
I can put the bolt in but it goes hard but going in it goes with angle of sear arm coming out it is against it and it hangs up
Is it possible to see the interference area? If so, as long as it is not the actual sear where it contacts the trigger arm, can a small amount be removed with a dremmel to allow the clearance you need?
Remove the rifle from the stock, squeeze the trigger and depress the sear. What is restricting the sear from going all the way back? this will be were you find your answer.
I'll bet it is the stock, the sear is rubbing against it. Like Robinhood said, remove the stock and try to remove the bolt, I'll bet it comes out. Look in the stock and see where it is rubbing. Remove a little material.
Bill
The action is not in the stock
it hits a stop on the arm the rifle Basix trigger is actually a 2 part trigger the trigger and the arm
the arm contacts the sear when it fires the sear drops but midway down the arm ther is a stop that the sear hits
with out the arm in it works fine so it’s in the stop
yea I thought about grinding the stop back a bit but did not want to hurt anything
the sear arm that holds the bolt in I also thought of rounding that point?? But I don’t want bolt coming out while cycling action
the action is a model 12 accutrigger never had trigger though I bought it stripped
the bolt is a used bolt not sure what action in came out of
The Rifle Basics sav2 has three holes for mounting the lever arm (if I remember right for different mechanical advantage).
Will the sear clear if it is mounted in one of the other holes?
Without seeing it I am guessing. If it does you will have to start all over but might be worth a try .
Chuck,
I think your problem is the accutrigger action with a borrowed bolt. Maybe Fred or Robinhood will be able to comment on that. I would hesitate grinding on the trigger or sear too. In my foggy memory it seems like I read about having trouble with the Rifle Basic 2 in a accutrigger action. Will the accurtrigger bolt interchange with a standard bolt?? Have you tried calling the folks at Rifle Basic??? I understand they have great customer support.
Bill
I had the same problem on two Model 12 with the Rifle Basis II Trigger kit. By modifying the bolt release stop material on top of the stop, I was able to make it work perfectly.
No other modification was needed for either the .223 or the .308 rifle. No stock mods were needed, it was the bolt release.
thats 3 holes for trigger the arm has just oneQuote:
Originally Posted by mnbogboy2
I did not mean the sear I meant the bolt release tec they are separate but they are 1 piece. I believe halftrack ran into same prob and fixed it I mean it’s so close that in the stock I can actually put enough pressure on the release to get it it like a 1/16 thQuote:
Originally Posted by bsekf
i can actually fix it with dermal with it assembled or even a file
thank you that was my thought alsoQuote:
Originally Posted by HalfTrack
Big, with the bolt removed and the trigger installed, look into the right lug raceway and see how much of the sear lever sticks up into the raceway. I have modified the top once like halftrack. It did not take much. The RB Sav2 is made a little more forward that the factory setup causing this issue.
Yea and it’s a brand new sear/ bolt release comes to sharp point easy fix the trigger itself I really likeQuote:
Originally Posted by Robinhood
Which pivot point you've chosen makes a difference as well as the overtravel screw, it's been awhile since I studied mine but I do remember that the trigger and the bolt release have to be in sinc
Might be the trigger stop screw needs backed out.
I have gone through the exact same problem.
Call Rifle Basix and tell them what the problem is. The will send you another sear. Several months ago they had a problem with the supplier.
They sent a new one and no more problem.
May I suggest this first, before the call.
Put the bolt in part way. Gently pull on the trigger and hold it down. Depress the lever while gently pushing on the bolt. Release the trigger entirely. The bolt will MOST probably continue on its way and close.