Printable View
Have all the necessary components for my next build with the exception of the McGowen 26" 1-8" ss barrel. Chassis is XLR Element with MDT fixed stock adapter and Luth-AR MBA-1 stock. Action is Rem model 700 single shot with bolt stop and ejector removed and with Calvin Elite trigger.
http://i.imgur.com/NQmIhSP.jpg
http://i.imgur.com/HRDvW3j.jpg
http://i.imgur.com/YBBSlrQ.jpg
Even though this thread ended up in the off-topic area, I couldn't just leave this thread with an unfinished rifle. So here are some progress photos.
1st up was to marry the action and the barrel.
http://i.imgur.com/W6j4o8J.jpg
I decided to do a skim bed even with having a chassis system. Here we are ready to apply the epoxy.
http://i.imgur.com/zptoUtB.jpg
Epoxy applied, barreled action back in chassis and clean-up began on excess epoxy.
http://i.imgur.com/5j5zq4u.jpg
Rifle all together. Next to install scope and begin load development.
http://i.imgur.com/0q82cIw.jpg
LOOOOKING Good
Really nice! I really like my Remage setup. Keep us updated on the finished product.....targets too!
Scooter
Thanks folks. Hope to get to the range tomorrow, weather permitting. Will begin barrel break-in/sight in with factory Lapua 139gr ammo.
Made it to the range this morning and shot a total of 15 rounds. 5 to zero and 2 groups of five for accuracy.
I believe it definitely is going to be a shooter, limited by my abilities on the trigger.
http://i.imgur.com/SE9xdJS.jpg
http://i.imgur.com/9BNskDK.jpg
http://i.imgur.com/K482OC4.jpg
I do believe you are well on your way [emoji6]. What bullets are you planning to reload in it?
Scooter
Hey Scooter.
I'm planning on 4 different bullets. 123gr(4PL6018) & 139gr(4PL6032) Lapua Scenar OTMs. 130gr Match-VLD-Target( #26503) & 140gr(Match BT Long Range VLD Target(#26409) Bergers
Lower that scope plz
Why? It works and suits my cheek weld.Quote:
Originally Posted by homefrontsniper
Sounds good, I'll be keeping up with this thread to see how things turn out. I'm thinking of a 6.5 something in the future.Quote:
Originally Posted by rbp75503
Scooter
You must have a BIG CHEEK
Have begun load development with 140gr Bergers, groups using N540 were so so, but RE-15 looks promising. Still have Varget and 4350 loads to try.
http://i.imgur.com/JgqJF1B.jpg
http://i.imgur.com/jRMB14p.jpg
Once again at the range. It looks like I have found the best combo for the 140gr Bergers using Varget. Eventually I will do some tweaking of distances from the lands, but I am pretty confident the present loading looks good. I was able to get a couple of groups in the .2s using H4350 so maybe some tweaks for those loadings would tighten the groups. A .187" with Varget is quite alright for the time being. This will probably be last post as there doesn't seem to be much interest in the further development of this rifle.
http://i.imgur.com/QZHrvYi.jpg
Time to stretch.
I do believe you've found a dandy load! Impressive!
Congrats!
Scooter
^^^^^^^ What he said!Quote:
Originally Posted by Robinhood
I wished I could stretch it out.:( But only 100 yds range is available to me.
Very nice.
May I know if your receiver and bolt is in stock form? If so, any problem with the big firing pin on small rifle primer?
Thinking of building a 6BR Norma.
Thanks.
The action and bolt are in stock form and have not been trued or bolt bushed and firing pin changed. The following photo shows that to-date there has not been any problems with primer strikes. I believe that the performance to-date of the rifle tends to show that it may not be necessary in all cases to have an action trued and other performance related mods done to achieve good groups. However, long range shooting may show the need for the mods.Quote:
Originally Posted by wingzero
http://i.imgur.com/kbHSGRX.jpg
Decided to buy a receiver and order a bolt from PTG with .062 firing pin and M16 mini extractor. Still undecided between McGowen and Criterion barrel.
How do you like your McGowen barrel.
How does it compare to your Bartlein barrel? Planning to build a 6mm BR Norma. Thanks.
Pic of the receiver.
https://c1.staticflickr.com/1/671/33...70d487b9_c.jpg
https://c1.staticflickr.com/4/3668/3...06c9a84e_z.jpg
The jury is still out on the Bartlein compared to the McGowen. Haven't really finished up load development on either one. However, already getting in the high .100" groups with the McGowen @100 yds. Yet to break into the .100s with the Bartlein. This is the second McGowen and the 300 Win Mag is a shooter too.
If you decide to go with a Remage and a McGowen then I recommend The Barrel Outlet in Hamond LA, specifically Nick to do the work. If you go Bartlein I recommend Southern Precision (Bugholes.com) and you have the choice of Remage or traditional fitting.