My old Savage 110, bedded to a McMillan HTG stock

My old Savage 110 flat-back with a NSS recoil lug and barrel nut, EGW scope base, and McMillan HTG stock. I'll see how it shoots with the factory barrel, but future plans are to re-barrel in 308 with a Rock 5R varmint barrel. It will be a switch-barrel gun. I have a magnum bolt head and will have another barrel in 300WM

I routed the factory bedding and laid down a good layer of Marine Tex last night. I got it all trimmed and cleaned up. Here's the process for anyone who's interested...

**NOTE** For anyone who wants to duplicate this, make sure you free-float the heel.

http://i292.photobucket.com/albums/m...ps356vaqiy.jpg

http://i292.photobucket.com/albums/m...psa5sjk3ie.jpg

http://i292.photobucket.com/albums/m...ps6g3qjzza.jpg

http://i292.photobucket.com/albums/m...psoo5hexb1.jpg

Recoil lug routing...
http://i292.photobucket.com/albums/m...ps5klc8tjx.jpg

Clayed, taped and release agent applied...
http://i292.photobucket.com/albums/m...psao7dniif.jpg

Leave the back of the recoil lug exposed, tape the sides and front...
http://i292.photobucket.com/albums/m...psbopoca6t.jpg

More clay...
http://i292.photobucket.com/albums/m...ps5taeimdb.jpg

Action set in the stock, epoxy cleaned off and factory screws inserted, coated with grease to prevent seizure...
http://i292.photobucket.com/albums/m...pslhf5tsup.jpg

http://i292.photobucket.com/albums/m...pscvqnfr5l.jpg

http://i292.photobucket.com/albums/m...psgfjivfs6.jpg

Excess clay in the mag well...
http://i292.photobucket.com/albums/m...psysn2nndg.jpg

Barrel taped for fore end alignment...
http://i292.photobucket.com/albums/m...ps0adxwlqg.jpg

http://i292.photobucket.com/albums/m...ps0adxwlqg.jpg

After setting for the night and breaking it loose...
http://i292.photobucket.com/albums/m...pshvtna8eh.jpg

Studs inserted to hammer on for removal...
http://i292.photobucket.com/albums/m...psxxekwmo8.jpg

All cleaned up...
http://i292.photobucket.com/albums/m...psnxagnlus.jpg

Recoil lug and barrel nut bedding...
http://i292.photobucket.com/albums/m...ps07mmlhxh.jpg

Receiver all cleaned up...
http://i292.photobucket.com/albums/m...psijlwxjic.jpg

http://i292.photobucket.com/albums/m...psh59e5bep.jpg

http://i292.photobucket.com/albums/m...pso3zadjtr.jpg

http://i292.photobucket.com/albums/m...ps5vu7qrnd.jpg

Perfect image of receiver machining...
http://i292.photobucket.com/albums/m...psquzljlda.jpg

I used a knife and razor to trim. A couple of small chunks came off when I was scraping. If I used a Dremel, it would have been flawless...
http://i292.photobucket.com/albums/m...psg1fdydpp.jpg

Invisible bedding...
http://i292.photobucket.com/albums/m...pslpojxwdy.jpg

http://i292.photobucket.com/albums/m...ps3l2vjmzv.jpg

http://i292.photobucket.com/albums/m...psabizv5gi.jpg

http://i292.photobucket.com/albums/m...psbo4mqtte.jpg

Nice job but I have a question.
You said for a switch barrel so how are you going to get the barrel nut to line up with the bedding you applied there.
My suggestion take your Dremel and grind out everything in front of recoil lug. It isn't needed there any way.

Thanks!

I grounded off the high spots on the barrel nut after I snapped the picture.

Tony.

More progress...

I had a friend mill off the first two rail sections from my EGW mount. This will allow my Zeiss to be set back to give me perfect eye relief.

http://i292.photobucket.com/albums/m...ps2f27mkvb.jpg

I also bedded the scope base. The back of the scope mount had a 0.010" gap over the flat of the receiver.

http://i292.photobucket.com/albums/m...ps66abh7im.jpg

It was still a little soft this morning, so I threw the base in the toaster oven to speed cure it for 30 minutes at 150˚. Worked great!

http://i292.photobucket.com/albums/m...psk6y2ooki.jpg

Next step is scope mounting, leveling and set fire!

Tony.