Printable View
Hey guys, I need to paint my stainless steel Shilen barrel. It's a 26" Select super Match Bull Barrel 300WM. I would like some good product recommendations that are lower cost.
My my first thought it flat black tractor paint or engine enamel. Here is a picture of the rifle to help with opinions...
http://i.imgur.com/4V52veJ.jpg
If it bead or sandblasted the finish will stick better. High end Brownells Aluma Hyde, bottom end, barbcue grill paint.
KG GunKote it is cheap easy to spray and very durable. Or just use cheap primer and touch up as needed.
If Dura Coat is done absolutely by the instructions it is incredibly tough. I hear people talk about how its no good and all, and I submit it was not done correctly. I have had it on a BVSS-S for over 5 years and it has exactly 2 pinhead size chips that are my own fault, and this rifle has NOT been babied (you should see the stock, LOL). I prepped it and had an auto body friend spray it and have been more than impressed. If you don't do the proper prep work, no finish is going to work correctly.
Is it basically a "scuff, degrease, dry and spray?"Quote:
Originally Posted by pbmax84
I just did one with a high heat flat black followed by a satin clear coat. It looks quite close to a factory matte finish but it is black and doesn't have the blue hue of the factory finish.
http://i.imgur.com/rL71U3B.jpg
The good ones I've seen are more along the lines of "degrease, blast, clean, parkerize, degrease, and THEN spray"!Quote:
Originally Posted by Russmerle
Kyrolon, Duracote, Gun Kote, whatever are all only going to be as good as the preparation work!Quote:
Originally Posted by DrThunder88
Ok, the problem is you used "good product"(high quality) & "lower cost"(cheap) in the same sentence. And it depends on what YOU refer to as lower cost. Is $100 low enough? Because for that, the barrel can be nitrided. Now that is very high quality-the best IMHO. And it's not the most expensive. But if are referring to MY kind of cheap, than that $100 is way out of the question. I have had very good results with VHT products. I was heavily into building turbocharged racing engines in my younger years, and used about every product VHT makes. By coincidence, they have a coating called exactly what your looking for... "Barrel Paint".
http://www.eastwood.com/vht-barrel-p...-B4RoCYMbw_wcB
I believe this is your best bet, on the cheap. But as others have said, it really is the prep work that makes the biggest difference. Have the barrel bead blasted if you can, if not, sand it VERY well with 800-1200g paper, than fine scotchbright. Clean it very well with turpentine, alcohol, etc.
I have used Dupli-Color "Low Gloss Black part # DE1634 Engine Enamel with ceramic with good success.
I've shot a few barrels/barreled actions with DuraCoat. It holds up well and prep doesn't need to be prohibitive.
Clean/degrease your item, some basic scrubbing and brake cleaner will work.
Rough/scuff the item. If you can do a media blast great, if not just pay attention to what you're doing, focus on creases, seams etc.
THOROUGHLY clean/degrease again, from this point on limit contact, wear gloves, prep for spraying.
Spray evenly and lightly, resist the urge to bulk up any areas, just go slow and steady, light coats over and over again.
Leave it set! This stuff needs to cure, give it the appropriate amount of time to harden, plan ahead and don't touch it!
Use accordingly. Really the prep, application and curing are pretty simple, just follow the steps for a great result.
Thanks! I'm going to look into duracoat as well but might try this first. Used on motorcycles and resistant to solvents, gasoline, etc...? This seems right up my ally.Quote:
Originally Posted by Dave Hoback
Ok so I bought flat grill paint. I am painting my stainless M1A barrel too and figured I needed the high heat stuff for that. I'm painting it tonight so I'll post some picks soon.
Thanks for the help,
russ
Quote:
Originally Posted by rovert
Ok never mind I just read horror stories about the BBQ paint. I'm going to pick up the high temp engine paint tonight.
russ
Aluma-Hyde II is your cheapest best bet. Clear the nozzle after you finish. You might even pick up some new nozzles just in case.
So so it didn't really turn out how I wanted it too... My fault though. I primed, painted with flat black engine enamel and then clear coated with a regular clear and not satin. I think if I would have waited and bought satin clear vs using what I had on hand it would have matched the receiver better. Here is the final regardless of the miss match...
http://i.imgur.com/dhOhFq9.jpg
http://i.imgur.com/cSRIW8g.jpg
If you want a more matte finish take some Scotch-Bright and lightly rub it.