Removed
Printable View
Removed
WOW Stang! Was this the rifle you mentioned to me on my thread in the scope/optics section? That's great you were able to salvage it..not only salvage but it's a real shooter too! Congratulations and thanks for posting this. I'm sure many folks would give up and believe the gun was a paperweight or a wall-hanger at that point!
Brian
Wow! I'm impressed.
Removed
My ex brother in law did the same thing to a 270 reciever and took a hammer to it befor I could get home! Dumbass lol. Guess he never heard about the 300lb gorilla savage hired to torque down barrel nuts.
I think twisting the action would be quite easy when removing a factory gorilla torqued barrel. Truing the action is one of the steps in T&T by SSS.
Wow. Good job. Thanks for sharing the info.
Removed
The Stevens 200 I just built was the very worst barrel nut I have ever experienced in my Savage builds. When I finally got it apart, there was an abundance of extremely small metal shot wedged in the threads. Once I was able to clean them out, everything worked fine. I suspect they were cleaning with the metal shot and it got into the threads at that time. BlitzfikeQuote:
Originally Posted by nastynatesfish
Like this one ?
http://i51.tinypic.com/2vxk8iq.jpg
http://i56.tinypic.com/adc3n8.jpg
All courtesy of this thread at Snipers Hide http://forum.snipershide.com/snipers...need-help.html
What? You mean I'm not supposed to jam a 4-foot long pry bar down through the ejection & magazine openings in the action to gain additional leverage?Quote:
Originally Posted by Westcliffe01
I didn't read through the entire thread over there, but the OP is lying through his teeth when he claims he used the action wrench as close to the nut as possible. Anyone with even the most minute amount of common sense knows that clamping to and applying pressure in the front by the nut won't cause the rear half of the action to twist up like a pretzel.
This guy is clearly one of those to whom my signature would apply.
Yes, my conclusion is that the OP is flat out lying. I suspect though that those who use the rectangular section of bar through the rear of the action run a similar risk. Perhaps after you have the factory barrel off and you tighten your own barrels more gently - maybe. I think the best solution is the wrench which only engages the front of the action in the space where the bolt lugs go and has a circular section at the back of the receiver (for a multi barrel rifle).
Lying?
Strangfish,,,they are sugesting the OP at the hide is lying about how he bent the action in the above pictures. I do not think they are refering to your post
Removed
Removed
dem pipe wrenches are a gunsmiths best friend Stang! :( :yield:
Removed
Quote:
Originally Posted by stangfish
Mine too.
I'm pretty sure I straightened that action up, if not it was one that looked that bad.Quote:
Originally Posted by Westcliffe01
Removed
Removed
Ha! I remember that thread. I also remember contemplating buying it (clearly, I hadn't been drinking enough).Quote:
Originally Posted by stangfish
Stang, you've got to take and post pictures of these misadventures.
Removed
Indeed, I would qualify twisting an action as a misadventure. More properly though, "Please post pictures of your step-by-step repairs of other people's misadventures."Quote:
Originally Posted by stangfish
Removed
Don't have one of those, but I know I want one!
Plenty of thing I can't do that I'm interested in learning about.
Rarely have I acquired knowledge of one thing that hasn't influenced another area of my life (E.O. Wilson uses the term 'consilience', or a jumping together of ideas, to describe it).
On the other hand, I can understand if its a hassle to carve out extra time from your schedule so that I can geek out :)
removed
Stang, I have one that gets a workout. I use it for everything from my gunsmithing to mill work. I frequently use it to set my rotary table in the vertical direction in my setups. Great tool.Quote:
Originally Posted by stangfish