Stock to fit 112 LA Single shot
I got what I though was a deal on an older 112 single shot that had been re-barreled to 7-08. The stock was trash so I ordered a Bell & Carlson stock from Brownells to fit a Savage 110/111/112. Turns out the hole spacing is too long on the stock. I was sure I had a long action--I measure the spacing at 4.53" I called Bell & Carlson and was told they make stocks with hole spacings of approx. five inches and approx. four and a quarter inches--I didn't write down the exact dimensions but I did note that my gun's spacing is about midway between the dimensions they quoted. Their rep said something like "That's Savage for you--they've changed their hole spacing over the years." I had planned on filling in the stock's magazine recess with Bondo or something, but if I were to use this stock it would mean routing out the area for the recoil lug, creating a new shoulder for the recoil lug, and drilling a new hole for the forward action screw. Does this sound feasible, or does anyone know of a source for a stock that will fit?
Re: Stock to fit 112 LA Single shot
Maybe you have a J action Savage?
Re: Stock to fit 112 LA Single shot
Re: Stock to fit 112 LA Single shot
What's a J action? Sorry, but I'm new to Savages and only a rank amateur gunsmith.
Re: Stock to fit 112 LA Single shot
Quote:
Originally Posted by PeteVoss
What's a J action? Sorry, but I'm new to Savages and only a rank amateur gunsmith.
First Generation Short Actions:
The 1st Generation short actions are often incorrectly referred to as "Series J" actions. These actions will have a three digit model number (110, 112, etc), but are approximately 0.540" shorter than the standard long action.
Re: Stock to fit 112 LA Single shot
Hey Pete, What exactly qualifies as being trash? Cracked or just beat up?
Was looking into swapping a long action stock onto a J action a while back but found a J action stock. The easiest fix is finding or haveing someone make the right stock but if your handy with wood and can live with a little cobble there is a fix. You can epoxy a piece of wood (or plastic in this case) into the magazine cutout, plug the old hole and lug channel. Then drill the new hole for the action and set just the action in without the lug to mark the lug cutout. Then just bed the action + or minus pillars...I'd pillar bed it as long as your going this far. The barrel channel is gonna look a little funky where the nut is but I tend to hog out that area a little anyway so barrel changes are easier.
Your new hole will be right about where the magazine cutout starts.
Long action on top
J action in middle
Short action on bottom
[img width=600 height=332]http://photos.imageevent.com/cjnmn/guns/websize/09outandabout%20783.jpg[/img]
Re: Stock to fit 112 LA Single shot
great Pic CJ added it to the action length description in FAQ
http://savageshooters.com/SavageForu...ic,3883.0.html
I have cut the front piller out of a factory stock 10 short action and glassed it back in for a 110 short action. then bedded the action and lug.
http://img.photobucket.com/albums/v6...ge/savage1.jpg http://img.photobucket.com/albums/v6...ge/savage2.jpg
Re: Stock to fit 112 LA Single shot
CJ--Thanks for your reply and enlightening photo. What you described sounds similar to what I proposed doing to the Bell & Carlson stock I have. As I originally stated, my action has been rebarreled--don't know the manufacturer but it's a heavy varmint contour in SS and chambered for 7-08. The twist is very fast--I measured it at 1 in 7 1/2". Whoever did the work eliminated the barrel nut--it is headspaced the traditional way. My idea was to build a silhouette rifle, but in looking over the specs of barrels offered by Midway or Brownells I have not seen a 7mm barrel with a twist this fast. I would use the longest, heaviest Sierras--175gr.--but wonder if anyone has had any experience with a 7-08 and a 1 in 7 1/2 twist barrel.
Re: Stock to fit 112 LA Single shot
they were made during the "J" series of improvements. "J"s also came in long and mag calibers I have a CL in .270 and a 7mm rem mag with J on them.
Re: Stock to fit 112 LA Single shot
Cool I finally got a pic publishedhttp://img.photobucket.com/albums/v6...kendancing.gif
Pete
I was just wondering about the original stock. Are you looking to replace it for cosmetic or funtional reasons? Can always use a J field stock if its just banged up.
CJ
Re: Stock to fit 112 LA Single shot
To CJ in WY--Regarding original "J" series stock for LA single shot. The forend channel has been gouged out--it looks like a dull screwdriver was used. I had the idea of cutting and gluing wood to the outside surfaces until I had the shape I wanted, which was a stock with a lot of drop in it for offhand silhouette shooting, then send this "pattern" stock to Richard's Microfit for duplication in a cool laminate. I shaved wood off the sides of the forend but never got any further than that. If you're still interested you can have it for the shipping charge.
Re: Stock to fit 112 LA Single shot
To CJ in WY--I inadvertlently deleted your E-mail. My offer still goes--send me your address and I'll send the stock. I really don't want any more than the postage.
Pete Voss
Re: Stock to fit 112 LA Single shot
My email went belly up last week too...Give me a call and we'll work something out.
1-307-267-7624