Printable View
Are all hand primers equal?
Looking at the Lee Auto Prime Hand Priming Tool.
Do I also need to buy the package of shellholders?
Also looking at the RCBS Universal Hand Priming Tool.
$25 combined for the Lee stuff or $46.99 for the RCBS. Quite a difference for the same function.
I use the Lee Auto Prime and have never had any problems with it. You will need to buy the pack of shell holders for it. All the common shell holders are in the pack. The only caliber that I didn't get a holder for in the package was 7.62 x 39.
I use the lee too, its nice to grab 200pcs of brass and 2 boxes of primers and sit in front of the tv and prime
Lee +++++1
Steve
Yep.
I have the RCBS....and...if I knew now, what I did not know then...The Lee would be at my reloading bench. Actually, I would buy two of them.
+++++1 on that thought too!! Have one, and would like to keep a spare around.Quote:
Originally Posted by dcloco
I have the RCBS which I dont care for and therefore dont use and would like to know why the Lee is better? Better feel more leverage?Quote:
Originally Posted by dcloco
Caliber changes take...about.....that long. Seriously. You have a good "feel" of the primers seating and the low cost of the Lee setup. Really, cannot be beat.Quote:
Originally Posted by groupshooter
Ordered the Lee. Thanks.
I have the RCBS but have been thinking of getting a LEE and setting one up for Large and one for small.
The Lee hand primer is the only Lee tool I own. Never tried the RCBS so can't compare. The Lee works fine
Charlie
I have both a lee and a rcbs, the RCBS is a far better primer if your looking at quality and feel. The Lee is harder on the hands. The Lee has some advantages: it is smaller, easier to change out the shell holders, cost less, and the shell holders are cheap.
They both work good.
I have two lees, Had one forever and bought a RCBS so I would have two for the bench. I hated the RCBS and gave it to our very own Blue Avenger and bought another lee. I did not care for the RCBS at all.Quote:
Originally Posted by dcloco
i have 4 of them, 210m's, lr magnum, 205's, wolf srm, that way i never mix them up, i do my pistol stuff on the dillon 550.Quote:
Originally Posted by MikeCTX
And I really like it! and the one I already had. I also have one of them Lee ones that I use some times If I have to LOLQuote:
Originally Posted by EFBell
Try to get a feel for both. That's the only way you'll know. :D
the only real complaint i have w/ the lee is the round tray is too small to dump a batch of primers directly into, i dump in 3rd's, i/e pull a third of the box open and then flip everything over, then load, then do it again. one of the other brands has a square tray that fits a primer packet of 100 much better.
I have 3 Lees and 1 RCBS that I never use.
Lees all the way, easier & faster....& and lot less $.
???
Had 2 lee hand primers, both levers broke off next to body.
Have rcbs hand primer, no problems, 4x's as many primers set as both lees added together ?
I won't go back.
Also had two Lee hand primers that the handles broke off, but they were the original Lee (circa 1970's) and not the AutoPrime. I now have the AutoPrime and have not had one problem with it.
I have two Lee Auto-Primes. I keep one set up for small and one set up for large primers. The shell holders swap out very quickly. Buy two for the price of the RCBS.
I have both as well, a fairly new Lee and a very old RCBS. The Lee is faster but the RCBS allows me to seat primers much more consistently. I still use the RCBS for everything except when priming cut down .25ACP brass for my muzzle loader and .45 ACP .
Bob
if you follow the instructions & grease the pivot points..you didn't get broken levers..also gives much better feel
I had 2 Lee's and broke handles on both of them over about a 4 year period (yes, they were greased). The cut-out in the tool is not large enough to handle WSM cases, so ai had to prime them on the press (bummer). And it was really hard on the thumbs after awhile.
I switched over about a year ago to a RCBS Universal hand primer and couldn't be happier with it. You squeeze with your fingers, not your thumbs, and it uses no shellholders - just opposing spring loaded plungers that hold the shell centered over the primer hole. I'd use Lee's again if I had too, but this one is easy to use, has better tactile feel upon seating, seems sturdier, and requires no adjustments when switching calibers, unless you change from LR to SR cases.
Elkbane
As stated previously, I have a Lee and have had no issues with it. However, curious if anyone has used the Sinclair or K&M single primer - a bit slower than using one with a tray, but they do appear to be made of better material.
Just primed 400 .204 rounds using my Lee while watching TV. It does get hard on the thumbs after awhile. I'm considering Plasti Dipping the handle to add a bit of cushion. My only real complaint has already been mentioned - If they made the primer tray 1/8" bigger in diameter a primer pack would fit!
I have two Lee's and, like Elkbane, have only had one issue with them. They are too narrow for a 7WSM to fit. I had to open one of them a little bit with a Dremel tool. No biggie, took maybe 10 minutes.
If you are only going to load for one cartridge you may not want to invest in the package of shell holders. Also be aware that the priming tool shell holders and die shell holders are not the same.
Anybody try the Hornady?
I first bought a Lee to prime my cases. After awhile the handle broke and I had to buy a RCBS. The RCBS was a lot harder to set up and change from small to large primers.
I had ordered a handle for the Lee and got a second primer so I could load both large and small primers.
Everything worked good with the Lee and I set aside the RCBS.
Now that I am older and started using Wolff primers I went back to the RCBS as it is easier to push the primers in. The RCBS has the longer handle.
I still use the Lee on small rifle and pistol when using up the last of CCI primers but need the RCBS when using Wolff.
I have two RCBS primers. One set up for large, one for small. Takes less than a minute to change shellholders. Loaded many thousands of rounds without a hiccup. Never tried any others so I can't really compare. Priming 200 rounds gives you a pretty good grip workout.
I have had a Lee for eons-Yeah, I broke the handle, they sent me a new one and it's still going. I don't even know where the primer arms for my presses might be!! I know this is repetitous, but the reason I chimed in was to ask if anyone uses the press mounted auto prime II? I'm thinking about dedicating a small press and try to modify it to a short throw for those long sessions.
Thanks, Steve
I use the auto prime 2 and like it alot. I use the Lee Classic cast and with the stops its possible easier to seat the primers to a consistant depth. Anybody want to buy a RCBS universal priming tool?Quote:
Originally Posted by durango