6.5 Creedmoor: All Around Round?

I grew up with the same calibers as alot of other guys here I am sure. The 30/30 lever action was my first big game rifle. I broke it and went on to the 30-06. I shot the -06 for most of my years. Its a solid performer as it always has been. I then went to the 308 later because I wanted a hunter/target rifle with plenty of available brass.
Last year I bought the Savage 12LRP in 6.5 Creedmoor. I can honestly say it is the best rifle I have ever owned. This includes Remington 700's, Brownings, and 1 Winchester. I dont know about the longevity, but I do know it will perform. If the longevity is anything like the 22lr Savage my dad gave me in the mid seventies I will be ok.
I think alot of the reason I like it so much is the cartridge. It works well on anything in my area.
It serves as a great varmint rifle for crows and such.
It works well on long range dogs.
It works well on hogs.
It works well on deer.
I dont have any elk but I wouldnt be afraid to use it on them.
The rifle and cartridge have actually made me a long range shooter with confidence. I have no problem with hitting inside 8" out to 700 so far and I am stretching the range each trip to the field. I am consistently shooting under .5 moa at every distance up to 700 so far.
Anyone in the market for a great rifle needs to consider it. Its that good.
Has anyone else been this excited about the 6.5?
I am considering selling my other rifles and buying an AR chambered for it and a lightweight hunter chambered for it also. I like it that much. What do you guys think?

I totally agree!

Why would you want any thing else

It'll probably be my next caliber when I can

I think there are allot of things to like about the creedmoor. I still have not built mine yet but its getting close, just two more rifles in front of it.
I still go back and forth between the creedmoor (sa)and the sweed(la) for my 6.5 build but for a short action 6.5 I expect the the creedmoor has excited plenty of folks and is hear to stay.

Its here to stay even if i have to buy the equipment to stamp out rounds in my shop!

Quote:

---

Originally Posted by bflee

Its here to stay even if i have to buy the equipment to stamp out rounds in my shop!

---

That's were she really shines

Interested to see some comments regarding the creed vs the 260 Rem. I'm currently struggling with this decision...

Quote:

---

Originally Posted by upSLIDEdown

Interested to see some comments regarding the creed vs the 260 Rem. I'm currently struggling with this decision...

---

260 Pros: finally has some really good brass available.
6.5 creadmoor Pros: Everything else.
260 has bean around a while but I would not be surprised to see it's use tapered off significantly over the next few years.
Again I do not run and have not run either.... yet. After a great deal of research and having fought magazine length with high BC bullets in so many different cartridges and rifles: I can not even consider a 260 while the creedmoor is out there.

Seems like a lot of 260 guys use 7mm-08 Winchester brass anyway...

Norma is supposed to start making Creed brass sometime soon.

I buy the hornady match rounds and shoot them, then reload the brass. I have reloaded them at least six times now. I dont see a problem with the brass. Maybe I am missing something but I keep hearing this over and over.
Hornady, Nosler, and Norma all make 6.5 Creedmoor brass now. I have made a few from 308 brass just to see if I could. The 260 is a great round also though.

If I were going to build on a long action, I would build a .260 and seat the bullets out to make use of the extra mag length. If I were using a short action, it would be a 6.5 Creedmoor for the same reason- to seat bullets out where they belong. I really like the Creedmoor concept and it may be my next build.

I'm in the same boat, I'm really struggling deciding between a creed and 260. It has to be a short action because the stock I'm using is only made for a SA. I'm a believer in lapua brass, it's just so tough and doesn't loosen up primers. My buddy hasn't had a bit of trouble with his hornady brass in his creed although he doesn't have that many reloads on it. I like less body taper and steeper shoulder on creed but I want a different head stamp from my shooting friends when our stuff is on the bench. Heck I don't know, probably just hope that northland only has one or the other in stock when I call, then my decision is made. I'm hoping it's a 260rem match though! I think..

I don't get it, .260 outperforms the creed across the board. why was the creedmoor invented when the .260 already existed?

If you load a 260 to fit a short action, and a Creedmoor to fit a short action, you can actually get more out of a Creedmoor.
If you shoot factory or a long action you will get more from the 260.
Factory match rounds favor the Creedmoor, but reloading brass favors the 260. Hornady, Nosler, and Norma make brass for the Creedmoor now and the other manufacturers will soon follow.
I rolled both around in my head for a while before I purchased mine. I bought the Creedmoor because I could buy cheap factory rounds and then I reload the brass. It works for me, but I am pretty positive neither is going to "outperform" the other by much either way.

I have both, like both, and will continue to shoot both. I use the Creedmoor for hunting and it is fantastic on game.
Hornady brass has worked well for me, but Nosler brass is available for it now and in stock several places.

To me the creedmoor has the most bang for the buck for a hunting rifle. Very accurate, don't burn a lot of powder, recoil is not much more than a 243 and kills stuff like a 7 mag. Can't help but to like it.

Makes a hell of a target rifle also. It serves both well, thats why I like it.

My 11 Hunter in 260 has a 3" magazine. Kinda makes most of this moot. Now if we were discussing a rifle brand with a 2.8" mag then I might go CM.

If I were buying rounds instead of reloading I would definitely go 6.5 because the 260 factory rounds are like gold! The cheapest on gunbot is 1.55 a round and that isnt match ammo! I buy the factory stuff for 1.10 each in 6.5 and then I reload them several times. I have six reloads on the last forty so far (7 shots) and I have lost 2 pieces of brass due to my negligence. I emulate the factory round for my reloads and all is good. Thats all I need!

The Creedmoor is an excellent all around cartridge, especially for the bolt gun. European hunters have been using the 6.5x55 for Moose for many decades.

If you are thinking of an AR, the 6.5 Grendel might be a very comfortable choice because one can use the slightly smaller AR15 platform.

There is a reloading manual with a fairly extensive discussion of the suitability of hunting medium game with the 6.5 caliber all the way through moose. (http://www.65grendel.com/forum/showt...ading-Handbook) I would highly recommend the book even if one is only casually considering the Grendel because the primary difference between the two is how far out one can get reliable expansion of bullets. The Grendel gets to 300 yards and more with 16" to 18" for several bullets. The Creedmoor would get 100 - 150 yards more.

Its a great all around caliber. Others may excell in areas but it has a great balance.

6.5 Creedmoor is very easy to handload, and as everyone has said the Hornady factory ammo is both reasonably priced and accurate. There are also TONS of 6.5 bullets you can experiment with to tailor your handloads to whatever shooting situation you wish to address.

I really love shooting my 10FP-SR in 6.5 Creedmoor. Low recoil, excellent accuracy, great external ballistics (even with the relatively short 22" barrel). Plus, the 6.5 Creedmoor ammo plays nicely with the 10 round AICS mags I use.

http://personal.visualitymedia.com/p...m_hsp_1000.jpg

As far as basing these puppies on an AR platform--you're gonna need an AR 10/ LR 308 receiver for the creedmore--kinda hefty if you're thinking practical woods gun, though a few specialty versions are cutting the weight down to "near reasonable."

I recently built an AR 264 lbc--basically the same thing as a grendel. My experience with this 6.5 caliber in an AR is that it shoots fabulously--BUT--and this is a big but--it can be "finicky" with loads due to the complexity of the cartridge design, the bullet used and how it feeds in the ramps etc--so don't expect it be a "workhorse spray gun" like 5.56 or even 6.8 spc. 2's. Although the grendel clearly out-performs the 6.8 ballistically--I would now give the nod to the 6.8 if it was to be a hunting gun and used inside 300 yds in an AR 15 carbine style setup--only because of it's over-all proven reliability.

Having said all that--if you still are left with a hankering for a 6.5 in an AR15 compatible configuration--I suggest wandering over to AR performance's website (For informational purposes only) and scroll down the page and take a look at the soon-to-be-released "Six5." I think these guys are on to something and suspect that they too are focusing on a simpler case configuration that chambers more reliably than the grendel spawn (which also have "finicky" bolt issues BTW). Lot's of milheads want the grendel to be adopted by the military--I bet it will never happen. I'm watching this closely.

A 6.5 is one of my next builds...and after doing all the homework, mine will be a 260 Rem AI on a long action. Just can't beat it without going to like a 6.5-06 or a 26 Nosler!

Great choice and look forward to your results. I like the 6.5 bullet but 6.5 284 norma is as big as I will go with it--I'll take more heft in a bullet beyond that. On the other hand, I'm curious to see if Deano can get 5000 fps out of the 26 Nosler. ; )

I'm shooting a 6.5x284 this year as my deer, coyote, mountain lion, and antelope gun. For an "all around" caliber however I prefer the .338 Win Mag. The smaller 6.5 caliber isn't quite as versatile when you get to the bigger stuff, moose, elk, and bear in my opinion.

Quote:

---

Originally Posted by Vince

I'm shooting a 6.5x284 this year as my deer, coyote, mountain lion, and antelope gun. For an "all around" caliber however I prefer the .338 Win Mag. The smaller 6.5 caliber isn't quite as versatile when you get to the bigger stuff, moose, elk, and bear in my opinion.

---

My uncle used the .264 Winchester Magnum (Lat '50s and into the '60s) to hunt elk. He was very successful with the Sierra GameKing of the day, taking elk out to at least 600 yards. He was one of the first to actually tape balistic tables on his stock and to ensure they were right.

As for moose and bear, tons of moose have fallen to the 6.5x55 with standard bullets but I would suggest a 140gr all-copper hunting bullet if one intentionally goes after moose. Bear will likely be vulnerable too and having a couple of those 140gr copper bullets (Lapua Naturalis, for example) for the second or third shot is likely prudent if one is hunting an area where accidental encounters are possible. But, a larger caliber with heavier bullets is likely a smarter choice when the intent is to go after brown bear.

Quote:

---

Originally Posted by thermaler

... recently built an AR 264 lbc--basically the same thing as a grendel. My experience with this 6.5 caliber in an AR is that it shoots fabulously--BUT--and this is a big but--it can be "finicky" with loads due to the complexity of the cartridge design, the bullet used and how it feeds in the ramps etc--so don't expect it be a "workhorse spray gun" like 5.56 or even 6.8 spc. 2's. Although the grendel clearly out-performs the 6.8 ballistically--I would now give the nod to the 6.8 if it was to be a hunting gun and used inside 300 yds in an AR 15 carbine style setup--only because of it's over-all proven reliability.

---

Apologies in advance for continuing to be slightly off the Creedmoor topic --

Had your build been with a 6.5 Grendel SAAMI spec chamber and standard hardware, your experience could well have been different.

Several Grendel shooters have gone through the trouble of shooting factory ammunition in all available bullet weights. The results have been consistent sub-moa groups at 100 yards, sometimes below 0.3 moa. Cycling and feeding problems are near non-existent with properly installed hardware. Some of these shooters have also run groups using handloads with bullets as light as 85 grains to as much as 140 grains. Again, no problems with cycling, and accuracy consistently sub-moa with some truly outstanding groups popping up.

The few instances where this was not a Grendel shooter's experience have almost always been traced to non-standard chambers with the .264 LBC being one on the better performing non-standard chambers or to inappropriately selected bolt heads, etc.

The 'finicky' part of the loads is largely a result of the parallel freebore used in the LBC and most of the Grendel knock-offs. The compound throat in the Grendel was implemented precisely to ensure accuracy over a very wide range of bullet weights and nose shapes.

Quote:

---

Originally Posted by JASmith

Apologies in advance for continuing to be slightly off the Creedmoor topic --

Had your build been with a 6.5 Grendel SAAMI spec chamber and standard hardware, your experience could well have been different.

Several Grendel shooters have gone through the trouble of shooting factory ammunition in all available bullet weights. The results have been consistent sub-moa groups at 100 yards, sometimes below 0.3 moa. Cycling and feeding problems are near non-existent with properly installed hardware. Some of these shooters have also run groups using handloads with bullets as light as 85 grains to as much as 140 grains. Again, no problems with cycling, and accuracy consistently sub-moa with some truly outstanding groups popping up.

The few instances where this was not a Grendel shooter's experience have almost always been traced to non-standard chambers with the .264 LBC being one on the better performing non-standard chambers or to inappropriately selected bolt heads, etc.

The 'finicky' part of the loads is largely a result of the parallel freebore used in the LBC and most of the Grendel knock-offs. The compound throat in the Grendel was implemented precisely to ensure accuracy over a very wide range of bullet weights and nose shapes.

---

I appreciate your input--I've heard it both ways--that the compound throat design in a SAAMI complaint grendel can be touchy as well--but admittedly I've only experienced the 264 lbc flavor. I'm not questioning the accuracy--I've had groups that I've never seen in an AR platform and rarely even in a bolt gun.

My personal opinion is that the overall design with it's wide case (relative to a 5.56) and sharp shoulder angle is problematic in terms of adapting to a robust AR15 environment. I could of course be totally off base and wrong, and you're right I'm judging from my limited experience with a slightly modified version. Once again--just my opinion-- and I'm not suggesting it's not a great shooter.

I confess to being an old Geezer. Many years ago, I built a 6.5 x 55 Swede on a M98 action. This was long before the Creedmoor, the Grendel, or the .260 Remington had ever seen the light of day. In reading the ballistic comparisons for 140 gr bullets in the Swede, the Creedmoor, and the .260 Remington, I do not see where there is a nickel's worth of difference between them. If I am missing something, please enlighten me. Thanks.

I've never seen a Swede in the flesh (gun, that is) though I know they're out there. Part of the problem is relative late realization of the inherent accuracy of the 6.5 in this country, I think.

Quote:

---

Originally Posted by thermaler

I've never seen a Swede in the flesh (gun, that is) though I know they're out there. Part of the problem is relative late realization of the inherent accuracy of the 6.5 in this country, I think.

---

Could be. Today's astronomical prices on decent military rifles, not to mention ammunition, probably discourage interest in that caliber.

I just saw an ad for a new Heavy bbl rifle by Ruger (horrors!) in 6.5 Creedmore. Currently, I shoot both a 14" TC Contender and a rebarrelled Axis in 6.5 TCU. I have been 'tempted' by both the Grengel and the Creedmore. Those 6.5 mm bullets are fantastic......

Always the maverick, when everyone in my IHMSA group was flocking to the 7 mm TCU, I 'had' to go to the 6.5. I never lost a target.
ron

My "philosophy" about the 6.5 is that the American market is still searching for the ideal cartridge that will "break away from the pack" and assert itself as a true standard-bearer. I don't have anything against any of the current configurations--but they all seem to have issues which hamper them from gaining wide-spread acceptance across both target and hunting communities. Maybe some more wildcatting will find that ideal load?

Quote:

---

Originally Posted by thermaler

My "philosophy" about the 6.5 is that the American market is still searching for the ideal cartridge that will "break away from the pack" and assert itself as a true standard-bearer. I don't have anything against any of the current configurations--but they all seem to have issues which hamper them from gaining wide-spread acceptance across both target and hunting communities. Maybe some more wildcatting will find that ideal load?

---

I have been loading since 1966 so many cart. I cannot remember some of them . There are so many cal. that will do the same thing if the shooter does his part that we would not need any more. But where is the fun in that ? We have to keep trying for that ultimate load .

Quote:

---

Originally Posted by bythebook

I have been loading since 1966 so many cart. I cannot remember some of them . There are so many cal. that will do the same thing if the shooter does his part that we would not need any more. But where is the fun in that ? We have to keep trying for that ultimate load .

---

The ultimate load is the one that gets "SAAMI-ized" and embraced by the major manufacturers--the chambers, brass, etc follow--and the costs finally become reasonable. IMO that has not happened yet in any flavor of 6.5

Quote:

---

Originally Posted by thermaler

The ultimate load is the one that gets "SAAMI-ized" and embraced by the major manufacturers--the chambers, brass, etc follow--and the costs finally become reasonable. IMO that has not happened yet in any flavor of 6.5

---

True, being standardized through the SAAMI / CIP process is a necessary first step in popularizing a cartridge. Of course, the cartridge generally has a good following in the wildcat and specialty ammunition manufacturing community first. A notable example is the multiple decade history of the 25-06 as a wildcat before Remington standardized it.

After that, popularity depends on several factors, ultimately being determined by how many shooters actually buy rifles chambered for a particular cartridge. The easy path is a cartridge standardized by the military -- that brings an automatic popularity. Next is a major manufacturer whose marketing folks' imagination is triggered by a particular cartridge and they hype, place ads, and encourage articles by well-known gun-writers who, coincidentally(?), know that it is far better to pat than to pan these products. Last in importance are the actual ballistics of the cartridge.

At least seven cartridges in 6.5mm /.264" caliber have SAAMI Specifications, including the venerable 6.5X55 Swede that is enormously popular in Europe. Ammunition for this cartridge can be purchased for as low as $18.00 per box at Midway.

260 Remington ammunition runs at about the same price as what one calls 'standard' or 'normal' ammunition in cartridges like the .308 Winchester, 270 Winchester, 25-06 and the .243 Winchester with bargain basement ammunition running about $5.00 / box less. Ammunition for the 6.5 Grendel runs a tad less than that of the .260 Rem -- probably because less powder is used and less metal goes into the brass.

The real question is: "Has the 6.5mm / .264 caliber arrived as a major factor for the American shooting public?" My view is that it is getting there but agree that large scale acceptance of the caliber is in the (likely near) future..

6.5s will NEVER be as popular in the US as other "standards", due to a number of factors that involve historical precedence in this country (military use of 30 calibers, Jeff Cooper's regaling of the 270, OMFG its a Euro metric caliber GTFO, etc.)

Case in point: the classic recommendation of a 308 over ________ (insert more modern cartridge design with better ballistics here) for a new shooter.

Quote:

---

Originally Posted by BoilerUP

6.5s will NEVER be as popular in the US as other "standards", due to a number of factors that involve historical precedence in this country (military use of 30 calibers, Jeff Cooper's regaling of the 270, OMFG its a Euro metric caliber GTFO, etc.)

Case in point: the classic recommendation of a 308 over ________ (insert more modern cartridge design with better ballistics here) for a new shooter.

---

Never say never! I think eventually the SD/BC superiority of the bullet will assert itself in a "Chevy" cartridge that will gain widespread acceptance in the US market. : )

Maybe but theres a lot of banter of which 6.5 is best. I laugh when people complain about seating vlds to the rifling and have trouble in the other 6.5's. Or short brass life or velocity (Grendal)....theres a reason the hornandy engineers designed a new 6.5 from the ground up. Better brass and barrel life, good efficiency compared to the other 6.5's and still maintain powder capacity and neck length in a short action cartridge. Even allowing bullets to be seated long or short with no issues.

I think the big hinderence worth the 6.5 calibers, in America, is the, "If a little bit is good more is better" attitude of the typical American.
I say that as a 6.5x284 Norma and .338 Win Mag shooter.

Quote:

---

Originally Posted by BoilerUP

6.5s will NEVER be as popular in the US as other "standards", due to a number of factors that involve historical precedence in this country (military use of 30 calibers, Jeff Cooper's regaling of the 270, OMFG its a Euro metric caliber GTFO, etc.) Case in point: the classic recommendation of a 308 over ________ (insert more modern cartridge design with better ballistics here) for a new shooter.

---

Turning back to the OP, the Creedmoor is an excellent choice as an all-round cartridge for North American hunting -- especially if one handloads. At the light end are the 85-90 grain bullets that will give 243-like recoil and lots of fun for casual shooting and varmints all the way through to the 140gr Lapua Naturalis or 155-160 grain roundnoses that can be (and have been) used for Moose. This span of capability helps explain the popularity of the 6.5 in Europe.

Also, take a good look at the Hornady 120 gr GMX Superformance load for the Creedmoor. This is not too much for deer and antelope and a good choice for elk (see http://shootersnotes.com/ideal-bullet-weight/ or the calculator at http://shootersnotes.com/calculator/...bullet-weight/). The recoil is also mild enough that the hunter won't be as distracted as would be the case when using a .308 Winchester with 165 - 180 grain bullets.

These characteristics would make almost any 6.5 with a case volume anywhere from that of the Grendel through to that of 260 Remington an excellent choice for the beginning hunter who already has some experience with the .223 Remington. The Grendel enjoys lightweight rifles and is an excellent choice if one wants to use the AR15 as the hunting platform out to a few hundred yards while the Creedmoor is superb as a long-range round with very flat trajectories in bolt-action rifles. Both do fine near the muzzle as long as the bullets are built for the velocity.

I had the same dilemma a while back, 6.5CM vs 260 rem.
Die choices and brass steered me to 260.

I have built a .260 and two rifles in 6.5 Creed. All are great and all are super accurate. The .260 is nice because I can just buy winchester .243 brass and neck up and trim. The Hornady brass for the Creedmoor is great...I have fired one batch going on 5 times and it still has tight primer pockets and shows no signs of giving up. I don't think you can go wrong with either, but I think the coolness factor goes to the Creedmoor. That's why I chose it for my latest build already have one each in .260 and Creed.