Possibly. I just had to hog out the lug channel towards the trigger gaurd about 1/4in to get the action to fit. There is still plenty more fitting work to be done
Printable View
Possibly. I just had to hog out the lug channel towards the trigger gaurd about 1/4in to get the action to fit. There is still plenty more fitting work to be done
OK it looks like it is not deep enough. With the action laying in the inlet the vent holes are low. With the barreled action they sit high.
Last night I started to finish hogging out the barrel channel and I've got about all but the last 2in free floated.
After I finish hogging the barrel channel I'll start on the pillars but I've don't have much more to go until i can start laying the lacquer down and putting some lead down range
well finaly got off my butt and got the thing head spaced and did some work on the stock ita late now but ill post pictures tomorrow
Sent from my LM-G710 using Tapatalk
I removed a ton of material on the left side of the stock near the action where the action is milled. The radius around the back of the action where the safety had about 1/8in that needed to be knocked down. Around the ejection port the wood was a tad tall so I removed it and then in the area where the bolt release is I had to bring the cut about 1/2in forward and down some.
All the removal in these steps was a heavy rasp file. There is still a lot more fine finishing in the mentioned areas where im going to radius the edges and the. The major work will be on the forend where im going to taper the front a bit and possibly shorten it. I'll be starting my tapering just after the barrel nut. Then to pillar bed it and find the right color stain and spray some nice lacquer.https://uploads.tapatalk-cdn.com/201...a36b087fb0.jpghttps://uploads.tapatalk-cdn.com/201...b6e7f3698c.jpghttps://uploads.tapatalk-cdn.com/201...bd0fd56639.jpg
Sent from my LM-G710 using Tapatalk
As of today I see an issue with my magazine. I will need to get a different follower. Anyome have the part number for a 7.62x39 follower? .223 should be fine right?
Sent from my LM-G710 using Tapatalk
I've been wondering what ever happened to this project.
I stalled out because I moved to Texas what I'm back now
Sent from my LM-G710 using Tapatalk
Got the bolt handle cleaned up pin break. After work I'm bead blasting the action as well as the barrel because they're two different finisheshttps://uploads.tapatalk-cdn.com/201...3748a43bc7.jpghttps://uploads.tapatalk-cdn.com/201...9b3e898e20.jpghttps://uploads.tapatalk-cdn.com/201...43ce016d41.jpghttps://uploads.tapatalk-cdn.com/201...5fd8caf9e8.jpg
Sent from my LM-G710 using Tapatalk
I'm sure glad you could find your project after a move. Very interesting following your progress.
I blasted the barrel and action and everything looks good now.
https://uploads.tapatalk-cdn.com/201...98defce065.jpghttps://uploads.tapatalk-cdn.com/201...52bdeab78e.jpghttps://uploads.tapatalk-cdn.com/201...c16bf92a89.jpghttps://uploads.tapatalk-cdn.com/201...ab1a0bd841.jpghttps://uploads.tapatalk-cdn.com/201...def683fb4f.jpghttps://uploads.tapatalk-cdn.com/201...2f4859b5f2.jpg
Sent from my LM-G710 using Tapatalk
She was feeling photogenic tonight. The camera doesn't pick up anywhere near the character this piece of wood has but oh well the results will speak for themselves soon enough.
I have a hard decision to make and what colornto make it. I already have a custom blended mahogany and black walnut stained .270Win thats gorgeous so that color is out. What would you do?
https://uploads.tapatalk-cdn.com/201...1065340c7a.jpghttps://uploads.tapatalk-cdn.com/201...a35ade04e5.jpghttps://uploads.tapatalk-cdn.com/201...5a26477917.jpghttps://uploads.tapatalk-cdn.com/201...a60906cab2.jpghttps://uploads.tapatalk-cdn.com/201...f9a01701d7.jpghttps://uploads.tapatalk-cdn.com/201...1e5f65c881.jpghttps://uploads.tapatalk-cdn.com/201...0b2a172577.jpghttps://uploads.tapatalk-cdn.com/201...798a9f044e.jpg
Sent from my LM-G710 using Tapatalk
2https://uploads.tapatalk-cdn.com/201...789192ed27.jpghttps://uploads.tapatalk-cdn.com/201...9fec6ea735.jpghttps://uploads.tapatalk-cdn.com/201...7136918347.jpghttps://uploads.tapatalk-cdn.com/201...0f29c3cd94.jpghttps://uploads.tapatalk-cdn.com/201...d20b9c0421.jpg
Sent from my LM-G710 using Tapatalk
.270Win. Be easy on her she's seen her fair share of woods walking as she is my dedicated deer rifle.
https://uploads.tapatalk-cdn.com/201...7d42bb2469.jpghttps://uploads.tapatalk-cdn.com/201...98d2e48f0a.jpghttps://uploads.tapatalk-cdn.com/201...2ffa8ad777.jpghttps://uploads.tapatalk-cdn.com/201...3d04ad6d0c.jpghttps://uploads.tapatalk-cdn.com/201...58715df50f.jpghttps://uploads.tapatalk-cdn.com/201...c388eadcc3.jpghttps://uploads.tapatalk-cdn.com/201...dd171ad51f.jpg
Sent from my LM-G710 using Tapatalk
Sorry last ones for tonight. Both weigh 8.8lbs
https://uploads.tapatalk-cdn.com/201...9a850a307d.jpghttps://uploads.tapatalk-cdn.com/201...e362f91f42.jpg
Sent from my LM-G710 using Tapatalk
Oh interesting. You could just purchase a Savage 7.62x39 mag, part number 55221.
My guess is that you would have to call Savage for just the follower.
Yea I've been looking for the follower with no success.
Sent from my LM-G710 using Tapatalk
Today i did most of the finishing work on the stock. I took the bottom half down to 500grit. I only did the bottom because I still have to contour the top half with a belt sanderhttps://uploads.tapatalk-cdn.com/201...70a2c468d8.jpghttps://uploads.tapatalk-cdn.com/201...8aff116be1.jpghttps://uploads.tapatalk-cdn.com/201...39702d1b8b.jpghttps://uploads.tapatalk-cdn.com/201...8b212dbe7c.jpghttps://uploads.tapatalk-cdn.com/201...c8456a2e33.jpghttps://uploads.tapatalk-cdn.com/201...971f57efda.jpghttps://uploads.tapatalk-cdn.com/201...3964ad001c.jpghttps://uploads.tapatalk-cdn.com/201...b0c666059b.jpghttps://uploads.tapatalk-cdn.com/201...185a7d2fc3.jpg
These I think are the best pics. I may try to get a small video clip showing the shantoyancyhttps://uploads.tapatalk-cdn.com/201...d009068c33.jpghttps://uploads.tapatalk-cdn.com/201...b746ae2e1c.jpghttps://uploads.tapatalk-cdn.com/201...faa84e2014.jpg
Pretty stock!
I sanded for about 3 hours today. My arms are beat
I just had this same exact issue when I screwed my .284 Win barrel onto a short action 110 and feeding from a .308 magazine. The back tab on the mag housings angles towards the rear a little at the top, allowing the top round(s) to sit further back. As a result, they sit back further than the bolt can reach to get behind the case head so when you go to chamber a round it slides over for 1/2" or so then catches on the body of the case and pushes it forward ultimately resulting in a jam. Was also gouging the heck out of my brass.
Took it out to Fred and had him examine it and determined the easiest solution was to simply grind some thickness off the back side of the front baffle on the right side that acts as the bolt stop on the sear to allow the bolt to come back a little further. Didn't need to take much off, roughly 3/32" to get it feeding properly and reliably.
Attachment 5659
That is not the same as i was having. I'll post video in about an hour
This is what mine is doing
https://youtu.be/lIshPsozrvg
Time to shape the forend andthings are about to get rough
https://uploads.tapatalk-cdn.com/201...e27e1daa93.jpg
Oh my god so stressfull. Only rough shapped and a lot more to go. I was forced to make a decision that I've beennthinking about doing anyways. The white dot in the middle of rhe rosewood is a dowel and thats where I will now be putting a quick detach cup for a sling.
https://uploads.tapatalk-cdn.com/201...7266ea69fe.jpg https://uploads.tapatalk-cdn.com/201...1e22fbbfeb.jpg
https://uploads.tapatalk-cdn.com/201...f812bcb3ad.jpg
https://uploads.tapatalk-cdn.com/201...7adcbe9a97.jpg
https://uploads.tapatalk-cdn.com/201...4fb24edf33.jpg
https://uploads.tapatalk-cdn.com/201...9f2dd8a902.jpg
Looking good.
Is it just me, or does the left side of the forearm look a little thicker (wider) than the right side in the second to last photo. Maybe it's just the angle or lighting/shadow making it appear that way.
Its not necessarily thicker just one side is rounded more I think.
Well did a lot of work today and its starting to take better shape! At least I think. My girlfriend liked the blunt end the way it was before but oh well its my gun not hers.https://uploads.tapatalk-cdn.com/201...11df300824.jpghttps://uploads.tapatalk-cdn.com/201...ea53f27dd9.jpghttps://uploads.tapatalk-cdn.com/201...87beafb556.jpghttps://uploads.tapatalk-cdn.com/201...ed75e3c042.jpg
Looking good! I can't wait to see how it turns out.
Got some important parts I today. I don't think I'll put then in today but maybe this weekend.
https://uploads.tapatalk-cdn.com/201...73bc1a64ec.jpg
I ended up using 1 of the pillars to make both. This wasn't too hard as long as you have a belt sander, micrometer and a dremel. I did try to drill the holes 1 size at a time but it broke away the wood. This sucks but since I'll be using jb weld I think it'll be ok.
Notching the pillars to fit the action kinda sucked but oh well.https://uploads.tapatalk-cdn.com/201...8353beee55.jpghttps://uploads.tapatalk-cdn.com/201...a5326fa870.jpghttps://uploads.tapatalk-cdn.com/201...c0c2d3e02c.jpghttps://uploads.tapatalk-cdn.com/201...dfdba85acd.jpghttps://uploads.tapatalk-cdn.com/201...5635ac978f.jpghttps://uploads.tapatalk-cdn.com/201...b87d032cb4.jpghttps://uploads.tapatalk-cdn.com/201...c060144e68.jpghttps://uploads.tapatalk-cdn.com/201...da27264877.jpghttps://uploads.tapatalk-cdn.com/201...57db767653.jpg
A long over due update.
https://youtu.be/ZOGaHD7Beu8
Sent from my SM-G960U using Tapatalk
Very cool. Would love to se some up close photos now that it is 95% complete.
Still more shaping to do on the for end then a light 600grit sanding to the whole thing then lacquer it. I will be installing QD swivel mounts as well. 1 in the forest where you can see the dowel that holds the rosewood and not sure where in the butt yet.
The pictures can't show the chatoyance but soon enough is going to look awesome!
I do want to get lower rings as well but I'm super excited to get this going.https://uploads.tapatalk-cdn.com/202...a676c72329.jpghttps://uploads.tapatalk-cdn.com/202...a527fec9fc.jpghttps://uploads.tapatalk-cdn.com/202...a0a081ad37.jpghttps://uploads.tapatalk-cdn.com/202...f7726a1cdc.jpghttps://uploads.tapatalk-cdn.com/202...c7bc728e00.jpghttps://uploads.tapatalk-cdn.com/202...edd8ed5967.jpghttps://uploads.tapatalk-cdn.com/202...436685758d.jpghttps://uploads.tapatalk-cdn.com/202...b01093a5f2.jpghttps://uploads.tapatalk-cdn.com/202...f5670761af.jpg
Sent from my SM-G960U using Tapatalk
I finally got to shoot this sweet little thing!!!! Not bad for 1st shots using TulAmmo. It's such a sweet soft shooter.
https://youtu.be/MgjeWXfmbOA
Sent from my SM-G960U using Tapatalk
https://uploads.tapatalk-cdn.com/202...636674927a.jpg
Great job. It must feel great to have it done.