Veeeeery carefully.. LOL!
Actually, if you worried, just leave. It. It’s perfectly fine to bed the Action with the Mag Box attached. I would use wax & release agent on it, but it won’t interfere with the bedding.
Printable View
Veeeeery carefully.. LOL!
Actually, if you worried, just leave. It. It’s perfectly fine to bed the Action with the Mag Box attached. I would use wax & release agent on it, but it won’t interfere with the bedding.
This happened to me once when I first tried my hand at bedding. I used a compound that didn't flow and I used to much. The result was the stock expanded rather than the compound flowing out from under the action. Over time and under fire it gave up. Now i take a few reference dimensions and use less medium so the bedding material doesn't act like a wedge.
I'm guessing you missed the second paragraph where I mentioned it was accidentally dropped. That was the Walnut Richards also and not the Boyd's. Thought I had a picture of the delam on the Boyd's but I cannot find it. I had to cut the stock in half and email it to Boyd's before they would replace it.
Like I may have mentioned, my initial question led to another and another... This has become a project.
The bedding pillars I ordered were the wrong ones, so I am waiting for their replacements. I sprayed the barrel with Alumahyde (that went well) and now I'm waiting for it to air cure...
I've taped & waxed the receiver, but now see that there is a 1/32" sliver of wood showing between the receiver and back of the recoil lug... will that "compress upon firing or cause pressure & distortion? How to I relieve that... dremel out & build-back flush w/epoxy or...
Now I'm thinking about what to do about that sliver sticking out, how to install the pillars perpendicular, what to do about the front action screw escutcheon, and the order of steps to bed it...
So, I'm wondering if I should start a new thread where I can ask all my silly questions or just keep drifting this one in various directions (bedding related)...
Starting a new thread specific to the bedding might keep it more organized.
Not understanding the 1/32 sliver of wood. Can you try to post a picture? Or message me and I'll send an email address you can send a picture to.
Epoxy does go bad. You will know when you come back the next day and it is still soft. I have had to wait for a week one time with some RAKA. I stopped using theirs after the second time it happened. I was making wood boats for about 10 years before I got bored with it. I went with USComposites and never had any issues after that. I still have some that is about 7yo right now. I just used it and milled fiberglass filler to bed a Boyds Tactical stock from when they first made them. I have 3 different hardeners to adjust the speed of hardening. I will tell everyone this, Never use the fast quick cures as they are not strong at all. Use the slowest you can get away with.
Below is a pic with the receiver screwed in place.
The recoil shoulder "ledge" is the lighter line in front of the receiver (with the green arrow pointing toward it).
It's in a hard place to measure, but it seems to stick out about 0.02".
I am wondering how this would affect the recoil lug to receiver fit and if it would induce an angle or adverse pressure/recoil when everything is tightened down...
Also, if I need to make it flush, I need to figure a way to shave it off without making a mess of the inletting and possibly after relieving it, to build it back up to bear straight, smooth & flush with the lug (using a little epoxy). IF it isn't a concern, I'll leave it as is...
Attachment 9940
Nope! Don’t touch it. For starters, I think it’s more of a bevel you’re seeing there. Certainly looks like one in the photo. Second thing, even if the wood is sticking past a few Thous., the Barreled Action w/recoil Lug will seat & compress the wood where it needs to be when the Action screws are in & torqued down.
Thanks Dave, that's the info I needed to know.
The action screws were snug (not gut-n-tight).
Now that you mention it, it does look beveled in the pic... but it doesn't in person - 90* as far as I can tell (with and w/o the action in place), but I did wonder if it would compress or 'wear in' upon use.
I was worried there would be binding or uneven gap on the mating surfaces when assembled.
If it indeed is past the Action face too much, the Action Screws will be very difficult or unable to be screws in. If that happens, & the screws won’t screw in, then it may need modified. But again, if only a slight amount, the screws will seat & thread normally & the wood will compress.
A good note to live by, never pre-modify parts. Never modify anything based on assumptions. Only modify a part after you know it’s required. And even then, only perform a modification you are familiar with. Don’t ever alter/modify/machine anything because you think it should be done. Just some advice from a pretty OK fabricator.
Thanks for that good advice.
It will be easy enough to find out since I can screw the barrel+lug on and test fit to see if the screws will go in... if so, no worries...
.
.
.
Yep, it all went together fine... I couldn't see that area (my x-ray vision is on the blink) but I had no trouble snugging the screws down, and I could feel the action move into position.
Thanks again... now I will start another thread on installing the Pillars...