Changing caliber of a Steven's Model 200

I am currently trying to rebarrel my Steven's Model 200 in .223 remington to .243 winchester. I have the barrel,bolt head,magazine box as well as barrel wrench and headspace gauges. My problem is the front baffle. I definitely have a short action. The current baffle has a long leg on the outboard side that contacts the bolt stop. This prevents the bolt being withdrawn far enough to allow the longer .243 ammo to be feed from the magazine. I purchased another front baffle for a short action (sight unseen)and got the same thing I already have. My question is can I shorten the leg on the new baffle until it allows the bolt to be fully withdrawn or do I need one for a long action?

Found out a lot of what I was looking for on another thread. Still would like to know if I can cut the longer "leg" off of the front baffle?

I've trimmed mine down in the past and don't see any problem in doing so.

.If ur interested in getting rid of the 223 bolt and barrel shoot me a pm. Ide be interested in both for the right price! :-)

Brian

Okay.I shortened the front buffer and it works great! Now I need to know how to get the magazine out without having to destroy it?

I take a small flat blade screwdriver and put it under the rear clip in the same axis as the stock twist and lift until it gets in a bind. Go to the muzzzle end and pry upwards till it gets in a bind. Go back to the front untill it comes out. the spring will asssist the process. This is important; you may need to remove any proud plastic or "burrs" on the clip side of the action bed on the foreward end. Sometimes some material gets forced up from prying. A sharp knife or small file stroking only downward should do the trick. It is ok to have a low spot but a high spot is BAAAAD! It really is easy after you do it once. Good luck.

Thanks stang but this is a staggered feed rifle,the magazine is attached to the receiver. I can't get it loose without destroying it. I would like to be able to reinstall it sometime.

Quote:

---

Originally Posted by jimmyraythomason

Thanks stang but this is a staggered feed rifle,the magazine is attached to the receiver. I can't get it loose without destroying it. I would like to be able to reinstall it sometime.

---

All I do is pry it off with a large flathead screwdriver, very easy, off & on many times.

Quote:

---

All I do is pry it off with a large flathead screwdriver, very easy, off & on many times.

---

We MUST be talking about different magazines because that clearly won't work on mine!

The magazine is attache to the reciever I assume. Put the blade of a flat screwdriver under the top front tab in a slot in the reciever, at a 45 degree angle and give the screwdriver a rap,That should get the tab out of the slot it is in and the magazine will fall off.

El Lobo

Quote:

---

Originally Posted by ellobo

The magazine is attache to the reciever I assume. Put the blade of a flat screwdriver under the top front tab in a slot in the reciever, at a 45 degree angle and give the screwdriver a rap,That should get the tab out of the slot it is in and the magazine will fall off.

El Lobo

---

That's what I always do. Sometime takes a couple good pops.

I think I read once someone used a "C" clamp to squeeze the mag (front to rear), then popped it out with a screwdriver.
Curt

Quote:

---

Put the blade of a flat screwdriver under the top front tab in a slot in the reciever, at a 45 degree angle and give the screwdriver a rap,That should get the tab out of the slot it is in and the magazine will fall off.

---

Quote:

---

I think I read once someone used a "C" clamp to squeeze the mag (front to rear), then popped it out with a screwdriver.

---

Thanks,I'll give those a try.

I got the magazine boxes swapped out finally. I was trying to pry it out which wasn't working. I used a thick bladed screwdriver at the rear of the box and sharply rapped it with a hammer....it fell out without (much) damage to the box. I installed the new box in reverse order. Thanks for the suggestions!