Printable View
Has anyone run this stock yet? I just received mine and my barrel shipped today. The current rifle is a 110FP blind mag with top safety release.
Apparently according to Stockys I need to buy Savage Ultralite bottom metal and mag to use with the stockys stock.
Has anyone worked with this stock yet or a similar conversion?
Thanks
Harley
Let me know how it turns out. I have been thinking about doing the same thing with an old Long action flat back. I just need a source for the bottom metal. Any leads would be appreciated.
Quote:
Originally Posted by Hoss50
The ultra-lite bottom metal is the plastic unit used on a lot of specialty models (Lady Hunter, Lightweight Hunter, etc.) and can be purchased through Tactical Works (assuming this is a short-action).
https://www.tacticalworks.com/savage...metal-oem.html
This bottom metal option accepts the Axis-style magazines with the retention clip built into the bottom plate of the magazine.
https://gunmagwarehouse.com/savage-a...-magazine.html
In looking for a mag to order, you may see stock photo's on vendor sites of the old-style of retention clip that is just curved plastic rather than the spring-loaded slide button on the example above. The old style hasn't been made for a couple of years now so even if the pic shows the old-style you should expect to receive the newer version which is a vast improvement over the old ones.
I am still trying to figure this out.
According to savage my vintage blind mag stagger feed 110 long action cannot be converted to work with new Ultralite DBM.
So the stockys stock won't work, and they don't inlet for blind mag. They said I can return it for a restock fee which sucks because it doesn't say that it won't work, or only works with certain models.
The holes for the action line up and the main thing that I see doesn't fit is the top bolt release area, but it appears that the stock could be opened up to fit.
But if I do that and buy the bottom metal items from savage and it doesn't work, I am SOL on about $600.
Bell and Carlson had a stock that will work, but it is over 1lb heavier which sucks.
I am torn. I *think* I can make it work, but if I can't it will be an expensive mistake.
I can offer this before you make anymore decisions. Convert to a single shot. Its an easy process as the mag pops out with a screw driver inserted between the mag and action and then pry the mag out of the slot on either end. I would recommend this single shot follower called the "Fred Sled" from Sharp Shooter Supply. It mounts easy and is flush. Cost is nominal.Quote:
Originally Posted by Hoss50
http://www.sharpshootersupply.com/LoadingRamps.html
Easiest way to contact them is send an email to Lisa or Fred. They are busy folks but kind as heck...so give them a few days to answer!
sshooter@wcoil.com
Lastly I have always hated ejectors on single shots because its a pain to find spent rounds. So I always remove the ejector. After its gone from the bolt you just slide the bolt back and there is your spent round. Pick the spent round off the follower and put it in your pocket or round box!
Good Luck to you Hoss.... Larry!
Thanks Larry. This will need to be a repeater though. It is designed around the idea of being my short run hunting rifle for elk and black bear.
I just receieved my left-handed NextGen Ultra Carbon Hunter Composite Accublock stock for my long action UL in 7PRC. I'm very pleased with the fit and finish, but haven't shot it yet, as I'm waiting on a replacement trigger guard. My plastic one cracked.
The stock is extremely light @23 3/8 ounces, which is 4 3/8 ounces lighter than the tupperware stock. However, the Stocky's is forend heavy, making the rifle balance different, but not unwieldy. The main benefit is the stiffness. It just doesn't move. I will be able to run a UL bipod with no issues.
Attachment 10700
Some pics of the Stocky's Stock. BTW, these are currently on sale for $399
$399! Great. I just picked up a 243 that’s in the cheap Tupperware for less than that stock, but it would make a great upgrade. So would the magnum contour threaded 6.5cm barrel I have sitting here. Was gonna try to leave it along(somewhat!) and not dump a lot of money in it. Ya know, a budget rifle… but the wheels are turning..lol
I bet you could take the stock to a local machinist and hog out some of the fore end area to even it out and still keep the rigidity.Quote:
Originally Posted by Bleeb
SJC