Attempting my first barrel swap for my 90’s era 110 action. Must be factory set because it won’t budge. Barrel just spins in the vise and it’s cranked really tight. Tried PB Blaster and tried heat. It just won’t budge. Any tips or tricks?
Printable View
Attempting my first barrel swap for my 90’s era 110 action. Must be factory set because it won’t budge. Barrel just spins in the vise and it’s cranked really tight. Tried PB Blaster and tried heat. It just won’t budge. Any tips or tricks?
Hit the barrel wrench sharply.
You may need a better barrel vice or an action wrench, or you could just cut it off with a Dremel tool. I had to cut one off myself, (Dont Cut The Threads)!
dremel some cuts into the nut, don’t cut all the way through! Hit the wrench with a heavy deadblow hammer.
Might end up sacrificing the nut. I’m just nervous about cutting the threads. I’ve been beating on it with a dead blow.
The vice is the Wheeler with the wood blocks
If you’re real careful you could cut around the circumference of the bbl nut just ahead of the receiver. It should come off real easy after that. Just make sure you stay out of the receiver face!
did you put rosin on the wood blocks? i have had success by first wrapping a couple layers of masking or painters tape on the degreased barrel, and then applying rosin on the outside of the tape. the tape will defrom into the blocks and give a better bite.
(i just used powdered rosin from the racket sports dept of big box sporting goods store)
:o Had to grind one one time but I did it length wise. As Julia Childs once said,"Frightning!"
I have been lucky so far, so not much help. How about a sharp chisel in an air hammer? I use a hair dryer for heat.
I have better luck using an action wrench in my vice to hold the action and then spin the barrel nut off. Remember the barrel nut is a jam nut, you need to separate the action and the nut not the barrel and the action like a remy. Sounds silly I know but I have tried both ways and the action wrench method makes them all a breeze.
Sent from my Pixel using Tapatalk
^^^^ This ^^^^
Action wrench, lay it on the floor and whack the nut wrench with a dead blow. Never failed for me.
VICTORY IS MINE! I got it! Thanks for all of the help and great ideas. The secret ingredient turned out to be powdered cane sugar on the block. Hard to believe that’s all it took. Threads on the nut look bad. Need to replace it.
Wrap barrel with duct tape to stop slipping in blocks. Be careful with a action wrench, it is easy to bend the action rails. But, Cmgoff has it right, you are working against yourself with just a barrel block. Soak the nut and heat just the nut with a propane torch......not barrel too. Hit the backed up nut several times with hammer. Hit the barrel nut wrench a sharp blow with 2# steel hammer....not dead blow hammer! You want a SHOCK! If that fails, cut nut several places, just be careful not to cut threads. Since the nut is a loss....you could grind a cold chisel to fit the slots in nut and drive it off.
Bill
I have heard of people bending actions but have never actually seen it done. Savage barrel nuts are pretty easy compared to the Remington barrels and even those, so long as you are paying attention and only apply torque to the wrench weather than bending the action.
Also I really do not recommend using a hammer or a dead blow for any action removal. This is a good way to do unnecessary damage when a breaker bar could have been used.
Sent from my Pixel using Tapatalk
Cmgoff, Many times the actions are bent is when a hack puts something through the ejection port through the mag port to get leverage.
I couldn't find any in my small town so I used table sugar. It worked great. I wiped the blocks with a damp towel then sprinkled sugar on the blocks. The moisture held the sugar in place. That was the trick I needed to get mine off. I couldn't believe what a difference it made. The sugar just washes right off the barrel afterwards.