I am certain this has been discussed at length somewhere in this forum, but I can't find my answer using the search function. I did see how to tell the difference by taking the action out of the stock, but since it's in the middle of hunting season right now that ain't gonna happen. I am wanting to place an order for a McMillan A5, so I believe I will need this information. Is there any way to tell what I have without removing the action and risking loosing my zero? Thanks in advance.
Measure the front two action screws. 4.275" would be a stagger feed, 4.400" would be a center feed. Just over 5" would be a long action.
Stagger and centerfeed long actions the same action screw spacing, I think-
What I do is open the bolt and look at the mag- centerfeed mag "lips" are spaced close enough together where a round has to be shoved in between them- in other words, if you were to load some rounds in there, they would stack one directly on top of another, feeding single- file. A stagger feed holds them staggered, sort of side- by- side almost but not quite.Quote:
Originally Posted by geargrinder
that was going to be my suggestion. load it up and see if they are inline or staggered.
Both mags stack the cartridges alternaly below the top round. Centerfeed feeds from the center. Staggerfeed feeds from 1 side then the other side.
The opening at the top is smaller on the centerfeed and can be a pain to load till you get used to it. Staggeredfeed are easy to load.
I see.
So my mag has to be loaded by sliding one round front to back (if that makes sense). It sounds like (from the above descriptions) that the staggerfeed can just have the rounds pressed into the mag like loading a PMAG on an AR. Am I correct on this?
you press the centerfeed in straight. The lips are tight (no comments) and you have to push them in.
You can do it that way, CRNA, or you can just put the cartridge on the feed lips and push straight down and it will pop right in - no sliding. Your choice.
One thing that would help us answer your question is, 1st - what caliber , what model , round or flat back action ?
As is so often the case, the first answer is correct.Quote:
Originally Posted by geargrinder
I have a model 111 in 7RM.
Not sure what you mean by "back action". Sorry for the ignorance.
If the top of the receiver to the rear of the ejection port is rounded, it is commonly called a "round back" action.
Conversely, if the top of the receiver to the rear of the ejection port is flat, not rounded, it is commonly called a "flat back" action.
Snapped a pic for you guys. Here is what I have. I am thinking this is a centerfeed.
http://i59.photobucket.com/albums/g3...psbd5c5ba3.jpghttp://i59.photobucket.com/albums/g3...ps09e1a43c.jpg
http://i59.photobucket.com/albums/g3...psf3ab2756.jpg
Yep, it's centerfeed.
its center feed
what is the black ring in front of the barrel nut
please flip your rings around so we do not have to look at your nuts
drybean
Got any meat with that salad???Quote:
Originally Posted by CRNA
The rest of the barrel nut.Quote:
Originally Posted by drybean
Maybe they are left handed rings. Then the nuts would go on the right?Quote:
Originally Posted by drybean
Your wife is gonna be pissed when she sees what you did with her ponytail holder she's been looking for, lol. Good idea though, I use them to hold the two pieces of my fishing poles together when I break them down, they don't deteriorate like rubber bands. I'll even throw a little Christmas tip your way, Walmart sells them in a 100 pack for around $5. They make a great stocking stuffer and she will never notice when you need a couple, lol.
Yeah, it's just the smooth barrel nut.Quote:
Originally Posted by drybean
Ponytail holder isn't a bad idea, but it's paracord that I used (a little more manly) haha. Works great.Quote:
Originally Posted by jerkin
What works even better is a small black wire tie.