Problem Installing Barrel in Short Action

[GaCop]

Bought a factory Savage varmint weight barrel on eBay. It came in yesterday; I already had the old barrel removed from my action and had that all cleaned up; old barrel had the smooth barrel nut, so I used the pipe wrench to remove it. All went well with that until I had to clamp the old barrel in my shop vise to get the smooth barrel nut off with the pipe wrench it was so tight.

For the replacement barrel I used a standard barrel nut I had on hand. NOW the start of REAL problems. The nut would NOT screw all the way on the barrel. It would go on about 1/4" and then seize up? I tried the smooth nut too; it would not go on either w/o using the pipe wrench. The new replacement barrel would not screw into the action w/o jamming up right near the front scope base screw and will not move any further w/o using a lot of force. I've checked the action and barrel threads closely and cannot see any damage to the threads. What really blew me away was the OLD barrel will no longer thread back in and jams up just like the replacement barrel.

My question to Dave or anyone else is, what course of action is there to fix this (if any). Could the old smooth nut have caused all the problems? In 15 years of rebarreling Savages I've never run into this. I'm totally stumped.

[pdog06]

-Once you broke the smooth nut loose did the barrel unscrew out of the action normally? Like you could do it easily by hand I mean?

If the slotted nut wouldn’t thread on the new barrel, and that nut wasn’t on the existing action, then something has to be wrong with the new barrel threads. Which could also be why the old barrel will no longer go back on the action as well. I’m wondering if the new barrels thread were wrong, and you messed up the action threads when trying to the new barrel into it?

[J.Baker]

Have to agree with pdog, sounds like one item had some bad threads (new barrel most likely) and it messed up the threads on the other bits when you tried threading on the nuts or it into the action.

Expensive solution would be to purchase a tap and die set (4D Reamers may rent them as well). Other option would be to have a gunsmith chuck them up in his lathe and check/chase them.

Don't beat yourself up over it, it happens to the best of us. Just last month I buggered up the threads on the engine case mounting boss of a brand new motorcycle with just 3 miles on the clock. I had a heck of a time running a chasing tap in from the rear to clean them up as access on the back side where the threads were still good was super tight. I could rotate the wrench maybe 1/8 turn or so at a time and the threaded bore was just shy of 1-1/4" in total length. Suffice to say it took me a while! lol

10564 10565

[sharpshooter]

At some point, on either gun there was probably a piece of blasting media buried in the threads. The shot blast media seems to get into places you wouldn't think they could, but once they get bound up in the threads it effects both the barrel and the receiver. Lucky for me I have a tap and a die to clean them up.

[GaCop]

Have to agree with pdog, sounds like one item had some bad threads (new barrel most likely) and it messed up the threads on the other bits when you tried threading on the nuts or it into the action.

Expensive solution would be to purchase a tap and die set (4D Reamers may rent them as well). Other option would be to have a gunsmith chuck them up in his lathe and check/chase them.

Don't beat yourself up over it, it happens to the best of us. Just last month I buggered up the threads on the engine case mounting boss of a brand new motorcycle with just 3 miles on the clock. I had a heck of a time running a chasing tap in from the rear to clean them up as access on the back side where the threads were still good was super tight. I could rotate the wrench maybe 1/8 turn or so at a time and the threaded bore was just shy of 1-1/4" in total length. Suffice to say it took me a while! lol

10564 10565 I've been thinking that having a local gunsmith chase the threads and will look into 4D rental. I used them a few years ago when the throats in my Ruger Blackhawk cylinder were way too tight.

[GaCop]

At some point, on either gun there was probably a piece of blasting media buried in the threads. The shot blast media seems to get into places you wouldn't think they could, but once they get bound up in the threads it effects both the barrel and the receiver. Lucky for me I have a tap and a die to clean them up. Yes, the threads were loaded with it and rust. The barrel was not easy to unscrew. I ended up using a garden glove with rubber fingers and palm to get a hold on the barrel to unscrew it. I cleaned the threads well and copper wire brushed them thinking all was good.

[Blue Avenger]

it's very common for the front base screw to damage barrel threads also when there to long.

[Robinhood]

Sometimes it is as simple as carefully sanding the OD of the barrel threads. If you had a good 1"-2" micrometer and it measured close to 1.062 or larger that could be the problem. Some guys who cut threads leave metal that is pushed up and it makes the major diameter oversized. Example, I cut the major diameter of an od thread to a few under the nominal size. Then I cut the threads to the correct pitch diameter. I will clean up the thread with a kratex bar then measure the OD again. If it is oversized, I will go back with scotchbright or sandpaper and clean it up until I reclaim my original dimension. There are threading inserts that eliminate that burr/proud metal if you are willing to spend the money.

It may not be what I describe but it is an easy process to eliminate.

Good Luck GaCop

[GaCop]

it's very common for the front base screw to damage barrel threads also when there to long. Yes, checked that but not a problem.

[GaCop]

I'm sending the faulty barrel back to the seller on eBay. I found an X-Caliber 308 bull barrel that Apache Gun Works is selling also on eBay and got that for a very good price. I'll have a local gun smith chase the threads on Model 11 receiver. Thanks all.

[LHitchcox]

I had the same problem with an Axis. The bluing salts or whatever the little beads are caused me to bugger the action threads a bit while removing the old barrel. I was finally able to use the old barrel to dress the threads enough for the new barrel to fit. As a last resort there is a tool to dress the internal threads of the action.

[GaCop]

I had the same problem with an Axis. The bluing salts or whatever the little beads are caused me to bugger the action threads a bit while removing the old barrel. I was finally able to use the old barrel to dress the threads enough for the new barrel to fit. As a last resort there is a tool to dress the internal threads of the action. I tried that and darned near got that barrel stuck in the action.

[GaCop]

This action problem has been bugging me so I took another look at the action threads. I've now learned that visual clean doesn't mean REALLY clean. I went to work on the action threads with a 50 cal bore brush and bore cleaner again. This time I also used tooth picks and jewelers screw drivers. I used the side of the bore brush chucked into my Dremel on low speed to get into the grooves, then tooth pics, and finally the use of the flat blade screwdriver. Two cleanings like that and I finally got the original factory barrel to screw all the way into the receiver. Action is now ready for the X-Caliber I bought on eBay from Apache. Persistence does pay off in the long run.:becky::thumb:

[PhilC]

Good news!

[pdog06]

Wow you had a lot of stubborn gunk in there then! Good job being persistent and getting it all out.

[NF1E]

Congratulation. Persistence can pay off. Welcome hom GI. I got to RVN a couple month before you left.

[GaCop]

Congratulation. Persistence can pay off. Welcome home GI. I got to RVN a couple month before you left.:thumb:

[GaCop]

The Barrel from Jim LOVES 168 gr Gold Medal Match ammo. .600" so far at 100 yards and no indication of copper fouling in the barrel after 40 rounds. Now to find a good 175 grain handload. This barrel doesn't care for 175 GMM at all.

[Robinhood]

The Barrel from Jim LOVES 168 gr Gold Medal Match ammo. .600" so far at 100 yards and no indication of copper fouling in the barrel after 40 rounds. Now to find a good 175 grain handload. This barrel doesn't care for 175 GMM at all.

GaCop, There are a lot of great powders for the 175's with that 1:10 twist you can even shoot the 185 or. What do you have?

[GrenGuy]

I'm sending the faulty barrel back to the seller on eBay. I found an X-Caliber 308 bull barrel that Apache Gun Works is selling also on eBay and got that for a very good price. I'll have a local gun smith chase the threads on Model 11 receiver. Thanks all.
Is this Jim (James) Skinner, of Apache Gun Works fame ?