Single feed sled

[Hylander]

Who makes a good single feed sled for a 110 short action?

[roboshooter]

Found this but have not used.
http://www.sharpshootersupply.com/LoadingRamps.html

[Turkeytider]

Found this but have not used.
http://www.sharpshootersupply.com/LoadingRamps.html

I have a polysled from them that I routinely use in my 110 .223. It works fine. I did have to shave a bit off of the rear tab of the sled in order for it to fit properly in the magazine well. A dremel is a wonderful tool! I`m pretty sure I got it from Kinney.

[pdog06]

They work perfect. About the only option other than making one yourself.
I have about 5 of them currently, using in various calibers with no issues.

I even have a couple I use with a repeater action in a stock inletted for a single shot(target action). All you have to do is round the sides off so it closely matches the round contour of the action and it fits just fine. I do mine with just a slightly loose fit when put in the stock, so I know it isnt causing any fitting issues between action and stock.
They will also work with a dbm stock. Simply Just install the follower and leave out the dbm mag. The stock/mag frame holds it in place, with just a slightly loose fit.

[roboshooter]

Thanks for the input on these. How do you place an order ? maybe Im overlooking on their website

[pdog06]

Call them

[pdog06]

Or put a want to buy ad here in our classifieds and maybe someone has a spare they’re not using

[jpx2rk]

If you are wanting to order from SSS, just download/print the order form from their website, and mail it in with a check, they are a bit slow but you get it in a few weeks or less depending on if they have any in stock or wait for the next production run.

[Hylander]

Thanks all.
I'll look for a used one or try to make my own.
Don't want to deal with SSS.

[RCE1]

I made my own out of PVC pipe. I fitted it to the magazine on top of the follower. Spring pressure holds it in place. Easy and cheap.

[Hylander]

I made my own out of PVC pipe. I fitted it to the magazine on top of the follower. Spring pressure holds it in place. Easy and cheap.

Nice, I might try something like that.
Any pics?

[GaCop]

I made my own out of PVC pipe. I fitted it to the magazine on top of the follower. Spring pressure holds it in place. Easy and cheap. :thumb: Great idea! Did you use 1" PVC?

[RCE1]

9539

They need to be fitted to the magazine, but it's something like this. Not high precision. LOL.

[Dave Hoback]

Pretty slick hombre:tea: Not a bad little DIY money saver.

Although… I’m still having trouble understanding why people can’t just set a round in by hand with the magazine in place?? I’ve done it half a KAJILLION times and never noticed a problem.

[roboshooter]

Nice ! I like it :thumb::thumb:

[roboshooter]

9539

They need to be fitted to the magazine, but it's something like this. Not high precision. LOL.



Nice ! I like it :thumb::thumb:

[Hylander]

9539

They need to be fitted to the magazine, but it's something like this. Not high precision. LOL.

Very nice
Thanks

[Hylander]

Pretty slick hombre:tea: Not a bad little DIY money saver.

Although… I’m still having trouble understanding why people can’t just set a round in by hand with the magazine in place?? I’ve done it half a KAJILLION times and never noticed a problem.

Not sure about other models, but on my 110 Hunter in .223 the mag follower is to low to lay a round and feed into the chamber. The bullet tip goes straight forward and hits the chamber face.

[KMW1954]

Pretty slick hombre:tea: Not a bad little DIY money saver.

Although… I’m still having trouble understanding why people can’t just set a round in by hand with the magazine in place?? I’ve done it half a KAJILLION times and never noticed a problem.

Dave I have a Model 11 223 Center Feed that just refuses to chamber a round by just dropping one into the receiver. If it is not in the magazine it doesn't feed.

[RCE1]

Some magazine followers lock the bolt back when the mag is empty.