torquing barrel nut

[arnie]

I replaced my barrel today using the wrench Northland sells. I saw torque setting of 35 to 40 foot pounds posted by a few that had replaced barrels. I used 2 different torque wrenches and can't even get a click at 10 pounds, and I feel it's very tight. Is there a spec when using these wrenches that is different than what i have been reading. BTW, tried 2 different torque wrenches and both acted the same.

[Dave Hoback]

That’s odd. Please don’t be offended as I don’t know your background, but how comfortable are you with DIY tasks with firearms and with using a Torque wrench? Many torque wrenches don’t really give a very audible “click”, more like they just “give” a bit. It’s actually not even very perceptible at 10lbs. Very easy to just push past the “click” or “give” as it is. Try a very slow soft touch when hold the wrench’s head with your support hand & push the handle slow & soft. Don’t just barrel ​into it.


On a side note; you don’t need to worry about going tighter. Many of us here who have been working on & building Savages for many years, Torque the Barrel Nuts much MUCH tighter. I tighten mine to 75ft.lbs. And I’ve heard of others going higher.

[J.Baker]

They torque them to 70 or 75ft-lbs at the factory if I remember right.

8979

[Blue Avenger]

As long as it is snug + your good. No tuning involved with torque, just keeping it together. Give your wrench a lite tap with a hammer if you question if it needs more. 3/8" wrench would be more sensitive if your going to do enough to warrant more tools.

[wbm]

As long as it is snug + your good. No tuning involved with torque, just keeping it together. Give your wrench a lite tap with a hammer if you question if it needs more.

+1

[Robinhood]

There are countless posts and articles by rifle builders that claim anything less than 75 ft/lbs has the potential for point of impact shift. Some big names go as high at 90 ft/lbs. I am one that will go 80-90 ft/lbs at 90* to the wrench. I like experience and the factory is normally who designs this stuff with their specs. All of us do what makes us feel comfortable.

[Nor Cal Mikie]

From the factory, the barrel nuts are GORILLA TIGHT. Ask anybody that had broken one loose for the first time. :eek: :eek:
Nothing fancy needed to secure the barrel. As mentioned, nut wrench gets a TAP with a steel hammer, double check the headspace and go shooting. Same with breaking the barrel nut loose for the first time. Don't pull, SMACK THE WRENCH. Steel on steel gets the job done.
Torque wrench is for cylinder head bolts, main bearing caps and lug nuts.

[charlie b]

I guess I got bad ones. Didn't seem to take that much to get mine loose, either the Axis or the 12. Getting the nut off the barrel (once it was unscrewed from the action) was a bit difficult with all the grit on the threads. I ended up cleaning up the threads then unthreading the nut.

I put mine back on without a torque wrench, but, it was 'really tight' with the 1/2" bar.

[Nor Cal Mikie]

I can break my barrels loose, (after the first time) swap to another, set headspace and put it back together in less than 10 minutes. No torque or action wrench needed, ever!! NEVER had one come loose!!

[ragsflh]

i tap wrench once hard.good enough.

[pdog06]

so that’s the gorilla we’ve all been complaining about over the years of trying to remove some factory barrels….lol

[Balvar24]

so that’s the gorilla we’ve all been complaining about over the years of trying to remove some factory barrels….lol

I think that must be the new gorilla. I took a 112V apart from the late 70's and his cheater bar is about 1/2 the length my 6'6" 250lb frame needed.

[Fuj']

You know it's tight when you split a nut.....Any of my bench guns, I never torqued the nut
over 50 ft. lbs. But long gone is the nut. All my barrels are shouldered and at 40 ft. lbs.

[Dave Hoback]

I still love the Barrel Nut. Especially with these nuts I use now. I actually really do like the look of them. I find it visually appealing. LOL!

https://i.ibb.co/JmgSjJw/246-C00-D3-FE3-D-420-A-8-EDB-C7-B1-EA89-BA7-D.jpg (https://ibb.co/9cSdH5k)

https://i.ibb.co/bjVtB55/5-B972-C54-859-D-4683-9991-31-DFC28-A9-C34.png (https://ibb.co/LDyKtdd)

[Fuj']

Dave.....I ordered one of those nuts from the maker in Canada. I just thought to
try it on an action I switch barrels a lot for fire forming my cats. I was disappointed
on how sloppy the threading was. They sent me a return tag, and it went back. As an
after thought, I just had them refund the money. It's a shame because generally it's
one hell of a nut. Oh.....It did'nt fit my 2 standard wrenches.

[Dave Hoback]

Hmm. None of that on mine TV. They even gave me the wrenches with. I ordered one & it was lost in the mail. So they sent me another. Few days later the first one showed up. They told me to keep both. Good CS..good business.

[Fuj']

Hmm. None of that on mine TV. They even gave me the wrenches .

Did you try your standard wrench on the new style nut ?? There was nothing really stated that
you had to also purchase their wrench. It was apparent that my standard wrench's were too small
in diameter.

[Dave Hoback]

Did you try your standard wrench on the new style nut ?? There was nothing really stated that
you had to also purchase their wrench. It was apparent that my standard wrench's were too small
in diameter.


Man! I completely missed this question. Sorry about that Fuj’. Standard wrench works perfectly fine on these Barrel Nuts. The company just makes a wrench also. It’s smaller & red. I didn’t buy it extra. The company just gave it to me free. Their customer service was really good.

[Nor Cal Mikie]

So who is making/selling those new style barrel nuts? Liking the looks. :cool: And the standard nut wrench fits?

[Dave Hoback]

So who is making/selling those new style barrel nuts? Liking the looks. :cool: And the standard nut wrench fits?

Mike, that one I use is from International Barrels in Canada. Can’t buy a barrel directly from them, but the barrel nut is no problem. Here is the pretty extensive list of ALL aftermarket Barrel Nuts available. Several of us were discussing them in a thread & Jim put a nice Article together showcasing them. https://www.savageshooters.com/content.php?585-Got-Nuts-Savage-barrel-Nut-Options