View Full Version : stock and bottom metal for Alaskan Brush Hunter?
aephilli822
03-12-2017, 05:38 PM
will this http://store.accurate-mag.com/savagelongactionbottommetalkit.aspx
and this https://www.gunpartscorp.com/ad/1433170.htm#1433170B
fit this http://www.savagearms.com/firearms/model/116ALASKANBRUSHHUNTER
??????
All will work except the barrel channel in the stock will need to be opened up a bit for the heavier barrel contour for the brush hunter barrel
aephilli822
03-12-2017, 06:17 PM
Great! Thanks! Even if it is a tupperware stock, I can reinforce it to work. (and black paint will cure that camo, too)
aephilli822
03-12-2017, 06:38 PM
3 rounds (and not even a fourth in the chamber) wasn't gonna make me happy. My own fault for not doing enough research beforehand. If this works out the way I want, I may spring for a Boyds laminate later.
Thanks again for the info!
Wait a minute.
STOP the PRESSES!
It does not say the stock is inletted for "bottom metal". If it is the stock for the new Trophy Hunters, it won't accept bottom metal (Newer TH's have athe "bottom metal" molded into the stock.)
Therefore, I cant say for sure.
aephilli822
03-12-2017, 08:09 PM
Do they have the trigger guard as part of the stock? Oh well, if not, I'll have to start over. :frusty:
We'll see when it gets here. (did I mention ordering things without enough research?) :redface-new:
aephilli822
03-12-2017, 08:17 PM
Worst case, I get some Factory mags and sell the stock and mags when I get the Boyds.
The stock will not come with trigger guard. They are avail, though.
aephilli822
03-12-2017, 08:58 PM
Trophy Hunter has side or bottom bolt release?
aephilli822
03-13-2017, 07:39 AM
yep, my luck yer prolly right. we'll see when it gets here.....:rolleyes:
aephilli822
03-21-2017, 08:19 PM
Well, looks like it might fit. the stock takes bottom metal and the magwell is only a few thousandths from seating in it. tomorrow i will check the fit of the action in the stock.
aephilli822
03-21-2017, 08:22 PM
i still wanna know who thought 3 rounds total in a "dangerous game" caliber was gonna cut it?????:confused::mad::frusty:
aephilli822
03-22-2017, 08:41 PM
did some opening of the barrel channel, and a fair amount of deepening the back half of the opening for the mag well (the infamous Dremel strikes again), and i'm about ready to shim for mag depth and bed everything
any advice, hints, tips, warnings?
aephilli822
04-08-2017, 06:38 PM
http://i346.photobucket.com/albums/p426/aephilli_photo/20170408_170855_zpskkdsmapr.jpg (http://s346.photobucket.com/user/aephilli_photo/media/20170408_170855_zpskkdsmapr.jpg.html)
aephilli822
04-08-2017, 07:01 PM
Didn't need shims, the bottom metal is a little "proud" from the stock
everything feeds and functions, but the whole ordeal has really soured me on this one
it should function very well for what i wanted as a " pig, grizzly, and lion stopper" setup, but it may take a while to get over the bad taste
http://i346.photobucket.com/albums/p426/aephilli_photo/20170408_170801_zpsheuntyod.jpg (http://s346.photobucket.com/user/aephilli_photo/media/20170408_170801_zpsheuntyod.jpg.html)
or somebody may get a helluva deal on a 375 lion gun
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.