"Cheap way out" barrel/stock clearance

[powderburnz]

Anything wrong with this idea?

http://i1112.photobucket.com/albums/k481/chippewavalleywoodworks/2015-01/D19B3FC0-A184-4653-9CDC-BB0378E2B15F.jpg (http://s1112.photobucket.com/user/chippewavalleywoodworks/media/2015-01/D19B3FC0-A184-4653-9CDC-BB0378E2B15F.jpg.html)

http://i1112.photobucket.com/albums/k481/chippewavalleywoodworks/2015-01/C467E28F-07CA-4541-BE2E-3D46DF1748F1.jpg (http://s1112.photobucket.com/user/chippewavalleywoodworks/media/2015-01/C467E28F-07CA-4541-BE2E-3D46DF1748F1.jpg.html)

http://i1112.photobucket.com/albums/k481/chippewavalleywoodworks/2015-01/B8EA291D-CDB4-4B3F-BFBB-D285C16F392A.jpg (http://s1112.photobucket.com/user/chippewavalleywoodworks/media/2015-01/B8EA291D-CDB4-4B3F-BFBB-D285C16F392A.jpg.html)

http://i1112.photobucket.com/albums/k481/chippewavalleywoodworks/2015-01/F80D15DA-341F-4205-9C63-AF95340B0474.jpg (http://s1112.photobucket.com/user/chippewavalleywoodworks/media/2015-01/F80D15DA-341F-4205-9C63-AF95340B0474.jpg.html)

http://i1112.photobucket.com/albums/k481/chippewavalleywoodworks/2015-01/D9CC46E4-C024-4016-BB8B-31CB48FB11CA.jpg (http://s1112.photobucket.com/user/chippewavalleywoodworks/media/2015-01/D9CC46E4-C024-4016-BB8B-31CB48FB11CA.jpg.html)

[powderburnz]

Also, both washers under the front lug.

[powderburnz]

Bump

[powderburnz]

Anything wrong with this idea?

[JCalhoun]

How does it shoot with and without them?

[powderburnz]

1.3 MOA without. Haven't shot with yet.

[Stockrex]

in theory the resonating frequency of the bodies will be altered by the shims a bit,
for practical purpose you will not see any significant change rifle accuracy.
how much torque are you going to use? 20 inch/lb?

[powderburnz]

in theory the resonating frequency of the bodies will be altered by the shims a bit,
for practical purpose you will not see any significant change rifle accuracy.
how much torque are you going to use? 20 inch/lb?

15 in/lbs, not enough?

[Stockrex]

15 in/lbs, not enough?
as long as it does not rattle, do have pillars?
I asked the same for SSS stocks (with pillars) and I was told by the expert, "finger tight" is fine :-)

[powderburnz]

as long as it does not rattle, do have pillars?
I asked the same for SSS stocks (with pillars) and I was told by the expert, "finger tight" is fine :-)

If you look at the pics you'll see the front pillar, that's where I put one washer. No screws go into that pillar. Then the next pillar back is the one in the front bottom metal. I have a washer there too. The back pillar has a bottom screw that seats on wood not in bottom metal.

[DaveD]

Ive seen someone else use milk carton plastic to shim the action aswell.