Savage 116 30-06

[03mossy]

So I am going to be getting serious about getting my 116 Classic in 30-06 dialed in Thursday for deer hunting in November. I do not reload for this yet, I will once I have enough brass. Anyway I have a box of 150 and 165 grain Remington Core lokts that I used to sight it in. I will also pick up a box of 180's. As far as factory ammo goes what do other Savages like? I know each rifle is different but just thought I'd ask what other people are having luck with in the 116's? For deer hunting, longest shot possible is 300 yards, most 50-150.

[Luke45]

Thats a great rifle you have there! personally i would stick with the 150s or 165 if your shots are under 300 yards.

in my experience with the 30-06, the 180s velocity is just low enough to not really expand a whole lot in a deer sized animals. small exit wounds and slower killing than a 150-165 with a higher velocity.

Corelocts have worked great, as well as federal fusions. Most factory cup and core 150 gr loads @3000 fps with SSTs, corelocts, gamekings, ect will knock a deer in its tracks with a 30-06

[sixonetonoffun]

Still like that rifle!! No recommendations here but the old farts have always used 180's seems to me. If ya can get 3 to group inside a quarter I'd call er good.

[Luke45]

180 gr corelocts in a 30-06 exit 75% of the time on elk. probly overpenetration on deer unless you use a lighter constructed 180 like an sst

[Nathan3006]

Check out the numbers for the Nosler 165 gr Accubond.
https://fusiontables.googleusercontent.com/fusiontables/embedviz?viz=CARD&q=select+*+from+1C5o2xk_hWmBsTsTUWwoZ262XZOtOsNloF 2QDW28+where+col4+%3D+60057+order+by+col0+asc&tmplt=1&cpr=1

[big honkin jeep]

My 30 cals like the 165s. I usually hand load accubonds for several calibers, as far as factory ammo goes I've had good luck with the Federal "Deer Thug" in 165gr grouping well.

[03mossy]

Still like that rifle!! .

Thanks Me too! Pretty excited to hunt with it in a month. I stopped on my lunch break and picked up a box of the 180 core lokts, also a box of 165 Federal Fusions. So between the 4 loads I should find one the rifle likes enough for this fall.

I chose this gun and caliber for the sake of easy to find cheap ammo. I got to tell you it is very refreshing to walk into a store and have not just one but many choices to choose from in the caliber I am looking for. And $19 a box for multiple different loadings is a bonus. My other deer rifle is a 300 Weatherby and if you can even find ammo its $80 a box, I sold my 270wsm cause that wasn't much better.

When I start reloading for it this winter 165 Accubonds are for sure on the list!

[jonbearman]

One of the bullets I always liked was the hornady 165 spire point for deer. They shoot really accurate when handloaded and do a lot of damage so a blood trail should be really vivid.

[Nandy]

In my opinion, 180 is too much for deer and you risk little expansion. As someone else mentioned, 150 to 168. I used corelokts factory ammo in 165 or was it 160 for years. Good round, good exit holes, lots of blood and short trails. I am a fan of neck shots which dont take much to kill a deer but always prepared for them broad side shots. Once I started reloading I used nosler 150 silver ballistic tip with rl-19. sub moa groups out to 200 yds.

[03mossy]

Still haven't been to the range to test the 4 factory loads I have. Life keeps getting in the way... like yesterday I was at the range on my break, got the target stapled, walked back to the truck to grab the 06, then the phone rings and it's the nurse at my daughter's school saying she has a 102 temp... off I go and one more shooting session cancelled. Oh well

[03mossy]

Well that was disappointing to say the least. The barrel is still very very new with only 40 or so shots through it so I'm not panicking yet but still disappointed. It grouped, or should I say patterned, all 3 weights of the Rem's in 3-4" groups. The Federals were a hair better at right about 3". I waited about a minute in between each shot and about 5 mins in between each group. This being my first new centerfire barrel how long do these things take to settle down? As of now I wont hunt with it with groups this big, need to figure this out.

[03mossy]

http://i1110.photobucket.com/albums/h457/nyleswgentz/20141022_141359_zps1d1e0b25.jpg

[short round]

Check scope bases, & rings they may be loose.

[Luke45]

Check scope bases, & rings they may be loose.
Yep, every savage ive seen that shot over 2" groups the scope bases were the culprit

[Nandy]

Yep, every savage ive seen that shot over 2" groups the scope bases were the culprit

Not quite, I had plenty of of ammo that would shoot over 2" in some of my guns that shot sub moa at 200 yds with the correct reload and in a few cases with factory ammo. However, this is not to say that the problem is not the optics or something outside the gun itself.

[03mossy]

Should I give the barrel a good cleaning before the next range trip or keep it dirty?

[03mossy]

Should I give the barrel a good cleaning before the next range trip or keep it dirty?

[Nandy]

if you are not in the "break in" group I would leave it dirty. most of the stock barrels I have shoot do it better fouled althougt at some tike they need cleaning but generally we are talking hundreds of rounds.

[Luke45]

if you are not in the "break in" group I would leave it dirty. most of the stock barrels I have shoot do it better fouled althougt at some tike they need cleaning but generally we are talking hundreds of rounds.

Yep, leave it dirty for now. but if he shot 4 types of ammo all over 3 " it is probly the scope or bases.

[Nandy]

If you have another rifle that does well move the scope to it and try it and see if you get the same results. That is how I realized I had a problem with a combo Nikon scope. If you dont have a good known rifle/load combo it will be harder to isolate. However, taking down the scope, bases, cleaning screws and put it all back correctly will be cheaper that keep buying ammo. In my 110 the screws for the base are not all the same length, front base are shorter. Not sure if your 116 will be the same but keep a look out for that. Many will use the longer screws up front and not realize that very front screw is not tight but resting on the barrel thus not securing that base.

Good luck, let us know.