Savage 11vt stock

[fjames2016]

I have been searching for an aftermarket stock for my 11 vt, but I can't seem to find anything. Any suggestions? Looking for something synthetic preferably

[shooter0311]

Same problem here. Any luck on your end?

[Rosco]

Here are a few threads that might shed some light on your stock dilemma.

http://www.savageshooters.com/showthread.php?31045-Another-Model-11-VT-Stock-Question

http://www.savageshooters.com/showthread.php?30179-Savage-Model-11-VT-Aftermarket-Stock-Question

Looks as if a few members ordered Choate Tactical and in at least one case they were able to drop the barreled action directly in and it worked without issue. Hope this helps!!

[Uncle H]

A Bell-Carlson will work if you dont mind converting to a blind mag, you only have to buy one little clip to make it work. Here is My Dicks Model 11 VT converted.

http://i1325.photobucket.com/albums/u635/Uncle_HII/DSC_0460_zps7d3574be.jpg (http://s1325.photobucket.com/user/Uncle_HII/media/DSC_0460_zps7d3574be.jpg.html)
http://i1325.photobucket.com/albums/u635/Uncle_HII/DSC_0466_zps6f9b49d6.jpg (http://s1325.photobucket.com/user/Uncle_HII/media/DSC_0466_zps6f9b49d6.jpg.html)

[couldbe]

Uncle H
Could you post pics of the trigger area. Thinking about a VT purchase and would like a metal trigger guard.

Thanks in advance
Mike

[Uncle H]

Uncle H
Could you post pics of the trigger area. Thinking about a VT purchase and would like a metal trigger guard.

Thanks in advance
Mike

I will get you some pics up. I am still using the Model 11 trigger gaurd, it has the bottom bolt release. I am not 100% sure but I think you would need the Model 10 PC trigger gaurd and bolt release I believe it is metal. Other wise you would need to convert your action to a top/side release, to use the basic metal trigger gaurd this also can be done by getting the parts from Savage. I did have to do some minor inletting on the stock to get the rear of the trigger and the bolt release to clear, but it was very minor.

[Steelhead]

I replaced all the plastic bottom metal with savage metal parts and put all of it in a Choate stock. Worked well with bottom bolt release.

[couldbe]

Thanks for the 10 PC tip and posting those pics in the near future.

[couldbe]

Steelhead
Thanks to you as well. Possible that you share your source,part# and prices? I may be asking to much of you,but some photos of your rifle's trigger area would be great.

Mike

[Steelhead]

Steelhead
Thanks to you as well. Possible that you share your source,part# and prices? I may be asking to much of you,but some photos of your rifle's trigger area would be great.

Mike
i have a list with part#s and serial #'s I'll try to post after work.
Bottom metal from savage was like$110 or so.
Ill try to post some pics later too.
Does the a a VT use axis style mags?

[Steelhead]

Here is the serial # I used to order the parts and the part numbers(bottom bolt release) I used the #s from the 10FCP listed and would like to thank cron for posting that info, VERY HELPFUL.

http://i374.photobucket.com/albums/oo186/yellowheap/D63A9D83-55B3-486F-8B69-5D29ED0CBD52_zpsbe6b05mf.png (http://s374.photobucket.com/user/yellowheap/media/D63A9D83-55B3-486F-8B69-5D29ED0CBD52_zpsbe6b05mf.png.html)

My original stock inlet.
http://i374.photobucket.com/albums/oo186/yellowheap/GJB/DSCN1356_zps63945d07.jpg (http://s374.photobucket.com/user/yellowheap/media/GJB/DSCN1356_zps63945d07.jpg.html)

New stock and parts.
http://i374.photobucket.com/albums/oo186/yellowheap/GJB/DSCN1355_zps2b6dc199.jpg (http://s374.photobucket.com/user/yellowheap/media/GJB/DSCN1355_zps2b6dc199.jpg.html)



http://i374.photobucket.com/albums/oo186/yellowheap/GJB/DSCN1353_zps4d458e3e.jpg (http://s374.photobucket.com/user/yellowheap/media/GJB/DSCN1353_zps4d458e3e.jpg.html)

I hope this info helps.
This forum was a BIG help in my savage 260 build.
Of course I have to show what that work can do now:rolleyes:
Shot last Sat at 750 yards.
http://i374.photobucket.com/albums/oo186/yellowheap/78F8C172-6674-4B2B-B2B3-A8F146B60C1C_zpsytnfi9s3.jpg (http://s374.photobucket.com/user/yellowheap/media/78F8C172-6674-4B2B-B2B3-A8F146B60C1C_zpsytnfi9s3.jpg.html)

[couldbe]

Thanks for the pics/info. Looks like all fitted nicely.
I would like to covert a VT11 to a blind box,add metal trigger guard and mount to a B&C stock. Still looking to see if that can be done, by a DYIer. If not, I going to go the route you went.
I would fill the side sling depressions with epoxy, sand and spray paint. I really don't like those side slings.
Steelhead thanks for your time and efforts, your next project may include cleaning those fingernails, if those in the photo are yours:p:p
Mike

[Uncle H]

Thanks for the pics/info. Looks like all fitted nicely.
I would like to covert a VT11 to a blind box,add metal trigger guard and mount to a B&C stock. Still looking to see if that can be done, by a DYIer. If not, I going to go the route you went.
I would fill the side sling depressions with epoxy, sand and spray paint. I really don't like those side slings.
Steelhead thanks for your time and efforts, your next project may include cleaning those fingernails, if those in the photo are yours:p:p
Mike


It can be done, it will be a few days before I can sit down and do it, but i will take mine apart and show what I did to mine, I will have the part munbers also.

[couldbe]

Certainly a nice group of people here @ Savage Shooters!!!
Thanks in advance UncleH, will keep an eye out for your next post!!!!
Mike