22-250 to 257 rbrts

[Monkeymaster]

Hi,
I have an savage 112 in 22-250 Long action with a 26" bull barrel, and I have 2 Stevens 200 CF short actions a 243 an a 308.
I was needing a long action for a 270 a&b barrel I picked up on this site, and also wanted to eventualy do a 257 rbrts project rebarrel, that I had planned on needing a long action when I get a barrel.
What would I need to do with the LA 22-250, for either the 270 or 257 rbrts.
I would need to swap out the bolt head, would I not ?
Then, I wanted to place the 22-250 bull barrel onto on of my short actions, thus haveing a "new" short action 22-250. If I had to swap bolt heads for the 270, I would then have the old bolt head to go along with the old 22-250 bull barrel. The old 22-250 was a stagger feed, and the "new" short action would have to be a CF or a single shot, it is after all really a bench rifle with the 26" bull barrel, so a single shot is no big deal to me.
I have an action wrench, and nut wrench, and I have swapped out 3 other barrels, but they were barrel swaps using the same parent cartridge, 22-250 to 250 savage, and 25-06 to 338-06.
Any help would be great.
Thanks

[keeki]

hmmm. More than likely that long action has a short cut out for the short action mag so a 270 is out of the question and the 257bob is better built from a long action with a long action mag. Gonna have to measure and see if it has the long action mag port or the short

[keeki]

all of those have the same bolthead. 473

[Monkeymaster]

Magizine length, ok I'll have to check.
Same bolt head, that is good.
Thanks for the input.

[Slowpoke Slim]

No problem, put the 270 on the long action, and the 257 Roberts on the short action. It will fit. No issues at all.

I am not speculating.

I have one.

This one is my daughter's weather warrior, built from a 243 WW.

http://i490.photobucket.com/albums/rr268/slowpokeslim/Step14.jpg

Step 1: Unscrew old barrel

Step 2: Screw in new 257 Roberts barrel and set headspace.

Step 3: Tighten barrel nut.

You are done, enjoy!

It takes no other work/changes/alterations. Even the magazine was fine, feeds Roberts ammo flawlessly from the 243 magazine.

http://i490.photobucket.com/albums/rr268/slowpokeslim/P1050698.jpg

http://s490.photobucket.com/albums/rr268/slowpokeslim/?action=view&current=P1050700.mp4

[cgeorgemo]

No problem, put the 270 on the long action

Once you're sure the mag cut out on the 110 will hold a long action mag. As for the 257 on the SA well seeing is believing on that one.

[keeki]

no doubt the bob can be put in a short action. The question is gonna be the 112 in 22-250. some of those long actions were cut for a short action mag box.

[handirifle]

Slowpoke,
How well does it feed the longer bullets, like Barnes or similar?

Also for the OP, although I am not sure about dies brass etc, just looking at the pictures of the cases, the 257 AI offers a slightly shorter case length, and greater case capacity for even more zip, since you're re-barreling anyway. Just a thought.

[halfmile]

My short action Remmy will not allow moving the bullet up close to the lands, because the rounds will not fit the magazine.

This is not an issue, because it's a meat gun for deer, and It shoots MOA even with a lot of bullet jump.

Ruger made some Bobs with medium length actions, and that was good.

If accuracy was an issue I would not use a short action, unless a special chamber with very little freebore could be reamed.
HM

[Monkeymaster]

Thanks,
I need to get it out this week end and see about that magizine well.
Thanks again