View Full Version : Barrel nut
twarren
12-30-2011, 12:33 PM
Does the F10FCPK the law enforcement 223 still have the barrel nut.
picture on the website is a little deceiving. can't tell if it does or not....
i see the post the guy selling them. i'd say pictures pictures pictures....
stangfish
12-30-2011, 02:38 PM
IT has the new spooth barrel nut.
Very difficult to remove even using the SSS tool.
http://www.sharpshootersupply.com/images/Accessories/smbnw.jpg
It ha been my experience that heat must be applied. I have had to cut the nut off before.
http://i84.photobucket.com/albums/k31/nicholas306/SAV10AS-2.jpg
scope eye
12-30-2011, 03:18 PM
Hi I just use a pair of vise grips or a pipe wrench and don't even try to save it, for the price of that wrench you can buy several replacement nuts
Thanks Dean
Mudcat
12-30-2011, 05:24 PM
Can you use a regular nut in place of the smooth one. I know the threads are the same but I am wondering about if the Accustock has clearance for a regular nut? If so, anyone know why they went with the smooth nut?
Sent from my evil black iPhone using Tapatalk
scope eye
12-30-2011, 05:44 PM
Hi yes you can that is what I was refering to.
Thanks Dean
scope eye
12-30-2011, 05:46 PM
It is the same nut with out the splines.
Sundo
12-30-2011, 07:38 PM
What tool does Savage use to install the smooth barrel nut?
barrel-nut
12-30-2011, 09:48 PM
I think they switched to the new nut for two reasons:
1. Aesthetics (its purtier)
2. Lawyers. They want to make it as difficult as possible to discourage us from barrel-swapping. Also this would possibly cause people to buy more complete rifles, rather than just swap barrels.
OK, that's three reasons..
sharpshooter
12-30-2011, 10:04 PM
You left out the main reason....smooth nuts are cheaper.
snowgetter1
12-31-2011, 02:34 AM
PIPE WRENCH IT.
stangfish
12-31-2011, 03:09 AM
What tool does Savage use to install the smooth barrel nut?
That would be the tool in the picture above your post.
scope eye
12-31-2011, 07:54 AM
They blue the whole assembly after it is all together,it hides any tool markings, and also acts like loctite thats why they are such a !@#$%^&* to remove.
Thanks Dean
The smooth barrel nut is a solution looking for a problem. I say wear your nuts proudly, for everyone to see. For me at least, the nut is part of why I like the Savage, not something I need to get rid of or hide.
Pipe wrench it off, toss it and get a regular nut.
barrel-nut
01-01-2012, 04:02 PM
The smooth barrel nut is a solution looking for a problem. I say wear your nuts proudly, for everyone to see. For me at least, the nut is part of why I like the Savage, not something I need to get rid of or hide.
Pipe wrench it off, toss it and get a regular nut.
I'm with ya, man! No nutless rifles for me!
dksac2
01-01-2012, 08:26 PM
Much easier to do what my Gunsmith does, figure where the bottom of the ring will be, drill a hole and use a spanner wrench or a specialized wrench that just fits the ring with a precision dowel pin in it. You'll never see the hole and it's cheaper to make a set up that will work 100% of the time than the SSS wrench set up.
My best, John K
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.