small shank rethreading tool?

[JavRGV]

does anyone make a rethreading tool to fix slight damage to threads on small shank barrels?

javman

[geargrinder]

A thead file would work well. Not very expensive either.

http://www.amazon.com/KD-Tools-Thread-Restorer-Sizes/dp/B000K1GAI0

[stangfish]

If it is slight damage, a small triangular file works well. Some folks already have one in their tool box. Standard thread pitch is 60* and that just happens to be the same as the file.

However I really like the tool geargrinder suggested. Very easy to use and hard to over do it. They have saved my behind on many occasions like bearing lock nuts...but that is another tale.

Good luck.

[thomae]

A thead file would work well. Not very expensive either.

http://www.amazon.com/KD-Tools-Thread-Restorer-Sizes/dp/B000K1GAI0


+1 to geargrinder
Unless you can get a thread restorer die (doubtful for this size at a reasonable price), this is the correct tool for the job.

[Trent]

You can buy a die that is specifically made for the Savage barrel threads. You'll crap yourself when you see the price though.

http://www.brownells.com/.aspx/pid=41631/psize=96/Product/BARREL-RECEIVER-DIES

http://spinstage.http.internapcdn.net/Spinstage/userdocs/products/p_080598110_1.jpg

[Blue Avenger]

I have a tap that size I use after I mount scopes. It puts threads in the scope mount screws that are a bit long.

[JavRGV]

Trent,

I saw those and might as well buy another barrel lol.




You can buy a die that is specifically made for the Savage barrel threads. You'll crap yourself when you see the price though.

http://www.brownells.com/.aspx/pid=41631/psize=96/Product/BARREL-RECEIVER-DIES

http://spinstage.http.internapcdn.net/Spinstage/userdocs/products/p_080598110_1.jpg

[geargrinder]

I have a tap that size I use after I mount scopes. It puts threads in the scope mount screws that are a bit long.


You won't need loctite either. ;D

[stangfish]

For those of you who try using that die nut...make sure you back off on the adjustment screwbefore your first pass. Work the screw down slowly untill it is snug but only removes the damaged metal. It is fine line between removing to much and just the right amount. The closer you are to a class one rhread the better. By that I mean there should be no movement between the barrel and the action. At least that is my Philosophy.

[r29l20]

+1 :)

[michael word]

For those of you who try using that die nut...make sure you back off on the adjustment screwbefore your first pass. Work the screw down slowly untill it is snug but only removes the damaged metal. It is fine line between removing to much and just the right amount. The closer you are to a class one rhread the better. By that I mean there should be no movement between the barrel and the action. At least that is my Philosophy.


That would actually be a class 3 fit. You would in no way want a class 1 fit, that would be looser than a hardware store bolt and nut. The savage barrel to receiver fit is a class 2 fit for production purposes.

[Cycler]

I have a tap that size I use after I mount scopes. It puts threads in the scope mount screws that are a bit long.
Wouldn't just shortening the screw be easier? ???

[helotaxi]

I have a tap that size I use after I mount scopes. It puts threads in the scope mount screws that are a bit long.
Wouldn't just shortening the screw be easier? ???
Don't inject logic! There's no place for that here.

[243LPR]

Is it any wonder why gunsmithing prices are so high when you see the price of some of the tools they have to buy and some hardly get used!

[stangfish]

That would actually be a class 3 fit. You would in no way want a class 1 fit, that would be looser than a hardware store bolt and nut. The savage barrel to receiver fit is a class 2 fit for production purposes.


You are correct. I meant to say "Class Three" but was distracted in my thinking. I hope I explained it in correctly in the rest of my post. My intent was to offer good advice not bad. Thanks for the correction MW.

[HankC]

Will a 1"x20 TPI adjustable die works by leaving the die open? it is only 0.05" difference!

http://www1.mscdirect.com/cgi/NNSRIT2?PMAKA=03939204&PMPXNO=1725382&cm_re=ItemDetail-_-ResultListing-_-SearchResults

[HankC]

Will a 1"x20 TPI split adjustable die work by leaving the adjustment screw open? It is only 0.05" difference. MSC has one.

http://www1.mscdirect.com/cgi/NNSRIT2?PMAKA=03939204&PMPXNO=1725382&cm_re=ItemDetail-_-ResultListing-_-SearchResults